On 2019-03-09 3:39 pm, David Summers wrote:
This patch adds wifi support to the ASUS Tinker Board (S) machines.
This is provided by an wifi card (RTL8723BS) wired into the sdio interface.
It requires certain pins pulled, to enable the WiFi.
The schematics for these board do not show the WiFi connection, so the
connections have been taken from:
https://github.com/TinkerBoard/debian_kernel/blob/develop/arch/arm/boot/dts/rk3288-miniarm.dts
In particular the pulling of two pins.
This patch is almost identical to v1. A few additional line breaks for
readability. On Armbian, they did not use sd-uhs-ddr50, so this has
been removed. It does not change functionality. The ASUS patch set
sd-uhs-sdr104;.
Signed-off-by: David Summers <beagleboard@xxxxxxxxxxxxxxxxxxx>
Signed-off-by: Stefan Wahren <stefan.wahren@xxxxxxxx>
Tested-by: Tony McKahan <tonymckahan@xxxxxxxxx>
Reviewed-by: Robin Murphy <robin.murphy@xxxxxxx>
Erm, I don't think I did... :(
Please see section 13 of Documentation/process/submitting-patches.rst
for what that tag means.
FWIW this is the kind of patch I might have considered formally
reviewing if I had enough first-hand experience of the Tinker Board or
Realtek SDIO modules to judge correctness, but sadly I have zero of either.
Robin.
Test-by: TheSaint @ ArchLinux ARM
---
arch/arm/boot/dts/rk3288-tinker.dtsi | 40 +++++++++++++++++++++++++++-
1 file changed, 39 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/rk3288-tinker.dtsi b/arch/arm/boot/dts/rk3288-tinker.dtsi
index ef653c3209bc..0ffab1b7c940 100644
--- a/arch/arm/boot/dts/rk3288-tinker.dtsi
+++ b/arch/arm/boot/dts/rk3288-tinker.dtsi
@@ -5,6 +5,7 @@
#include "rk3288.dtsi"
#include <dt-bindings/input/input.h>
+#include <dt-bindings/clock/rockchip,rk808.h>
/ {
chosen {
@@ -96,6 +97,17 @@
startup-delay-us = <100000>;
vin-supply = <&vcc_io>;
};
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk808 RK808_CLKOUT1>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable>;
+ reset-gpios = <&gpio4 RK_PD3 GPIO_ACTIVE_LOW>,
+ <&gpio4 RK_PD4 GPIO_ACTIVE_LOW>;
+ };
+
};
&cpu0 {
@@ -336,7 +348,7 @@
&io_domains {
status = "okay";
-
+ wifi-supply = <&vcc_18>;
sdcard-supply = <&vccio_sd>;
};
@@ -416,6 +428,13 @@
rockchip,pins = <7 8 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
+
+ sdio {
+ wifi_enable: wifi-enable {
+ rockchip,pins = <4 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>,
+ <4 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
};
&pwm0 {
@@ -440,6 +459,25 @@
vqmmc-supply = <&vccio_sd>;
};
+&sdio0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdio0_bus4>, <&sdio0_cmd>, <&sdio0_clk>, <&sdio0_int>;
+ max-frequency = <50000000>;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ vmmc-supply = <&vcc_io>;
+ vqmmc-supply = <&vcc_18>;
+ status = "okay";
+};
+
+
&tsadc {
rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
