Add the lm3532 device tree documentation.
Remove lm3532 device tree reference from the ti_lmu devicetree
documentation.
With the addition of the dedicated lm3532 documentation the device
can be removed from the ti_lmu.txt.
The reason for this is that the lm3532 dt documentation now defines
the ability to control LED output strings against different control
banks or groups multiple strings to be controlled by a single control
bank.
Another addition was for ALS lighting control and configuration. The
LM3532 has a feature that can take in the ALS reading from 2 separate
ALS devices and adjust the brightness on the strings that are configured
to support this feature.
Finally the device specific properties were moved to the parent node as these
properties are not control bank configurable. These include the runtime ramp
and the ALS configuration.
Signed-off-by: Dan Murphy <dmurphy@xxxxxx>
---
.../devicetree/bindings/leds/leds-lm3532.txt | 113 ++++++++++++++++++
.../devicetree/bindings/mfd/ti-lmu.txt | 20 ----
2 files changed, 113 insertions(+), 20 deletions(-)
create mode 100644 Documentation/devicetree/bindings/leds/leds-lm3532.txt
diff --git a/Documentation/devicetree/bindings/leds/leds-lm3532.txt b/Documentation/devicetree/bindings/leds/leds-lm3532.txt
new file mode 100644
index 000000000000..7cf6739eafe0
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/leds-lm3532.txt
@@ -0,0 +1,113 @@
+* Texas Instruments - lm3532 White LED driver with ambient light sensing
+capability.
+
+The LM3532 provides the 3 high-voltage, low-side current sinks. The device is
+programmable over an I2C-compatible interface and has independent
+current control for all three channels. The adaptive current regulation
+method allows for different LED currents in each current sink thus allowing
+for a wide variety of backlight and keypad applications.
+
+The main features of the LM3532 include dual ambient light sensor inputs
+each with 32 internal voltage setting resistors, 8-bit logarithmic and linear
+brightness control, dual external PWM brightness control inputs, and up to
+1000:1 dimming ratio with programmable fade in and fade out settings.
+
+Required properties:
+ - compatible : "ti,lm3532"
+ - reg : I2C slave address
+ - #address-cells : 1
+ - #size-cells : 0
+
+Required child properties:
+ - reg : Indicates control bank the LED string is controlled by
+ - led-sources : see Documentation/devicetree/bindings/leds/common.txt
+ - ti,led-mode : Defines if the LED strings are manually controlled or
+ if the LED strings are controlled by the ALS
+
+Optional child properties if ALS mode is used:
+ - als-vmin - Minimum ALS voltage defined in Volts
+ - als-vmax - Maximum ALS voltage defined in Volts
+
+The values for each of the following can be found in the
+include/dt-bindings/leds/leds-lm3532.h
+
+ - als1-imp-sel - ALS1 impedance resistor selection
+ - als2-imp-sel - ALS2 impedance resistor selection
+ - als-avrg-time - Determines the length of time the device needs to
+ average the two ALS inputs. This is only used if
+ the input mode is LM3532_ALS_INPUT_AVRG.
+ - als-input-mode - Determines how the device uses the attached ALS
+ devices.
+
+Optional LED child properties:
+ - label : see Documentation/devicetree/bindings/leds/common.txt
+ - linux,default-trigger :
+ see Documentation/devicetree/bindings/leds/common.txt
+
+Example:
+#include <dt-bindings/leds/leds-lm3532.h>
+
+led-controller@38 {
+ compatible = "ti,lm3532";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x38>;
+
+ enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
+ ramp-up-ms = <LM3532_RAMP_1024us>;
+ ramp-down-ms = <LM3532_RAMP_65536us>;
+
+ lcd_backlight: led@0 {
+ reg = <0>;
+ led-sources = <2>;
+ ti,led-mode = <LM3532_BL_MODE_MANUAL>;
+ label = "backlight";
+ linux,default-trigger = "backlight";
+ };
+
+ led@1 {
+ reg = <1>;
+ led-sources = <1>;
+ ti,led-mode = <LM3532_BL_MODE_MANUAL>;
+ label = "keypad";
+ };
+};
+
+Example with ALS
+#include <dt-bindings/leds/leds-lm3532.h>
+
+led-controller@38 {
+ compatible = "ti,lm3532";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x38>;
+
+ enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
+ ramp-up-ms = <LM3532_RAMP_1024us>;
+ ramp-down-ms = <LM3532_RAMP_65536us>;
+
+ als-vmin = <0>;
+ als-vmax = <2000>;
+ als1-imp-sel = <LM3532_IMP_4_11K>;
+ als2-imp-sel = <LM3532_IMP_2_18K>;
+ als-avrg-time = <LM3532_ALS_AVRG_TIME_17_92ms>;
+ als-input-mode = <LM3532_ALS_INPUT_AVRG>;
+
+ lcd_backlight: led@0 {
+ reg = <0>;
+ led-sources = <2>;
+ ti,led-mode = <LM3532_BL_MODE_ALS>;
+ label = "backlight";
+ linux,default-trigger = "backlight";
+ };
+
+ led@1 {
+ reg = <1>;
+ led-sources = <1>;
+ ti,led-mode = <LM3532_BL_MODE_MANUAL>;
+ label = "keypad";
+ };
+};
+
+For more product information please see the links below:
+http://www.ti.com/product/LM3532
diff --git a/Documentation/devicetree/bindings/mfd/ti-lmu.txt b/Documentation/devicetree/bindings/mfd/ti-lmu.txt
index c885cf89b8ce..980394d701a7 100644
--- a/Documentation/devicetree/bindings/mfd/ti-lmu.txt
+++ b/Documentation/devicetree/bindings/mfd/ti-lmu.txt
@@ -4,7 +4,6 @@ TI LMU driver supports lighting devices below.
Name Child nodes
------ ---------------------------------
- LM3532 Backlight
LM3631 Backlight and regulator
LM3632 Backlight and regulator
LM3633 Backlight, LED and fault monitor
@@ -13,7 +12,6 @@ TI LMU driver supports lighting devices below.
Required properties:
- compatible: Should be one of:
- "ti,lm3532"
"ti,lm3631"
"ti,lm3632"
"ti,lm3633"
@@ -23,7 +21,6 @@ Required properties:
0x11 for LM3632
0x29 for LM3631
0x36 for LM3633, LM3697
- 0x38 for LM3532
0x63 for LM3695
Optional property:
@@ -47,23 +44,6 @@ Optional nodes:
[2] ../leds/leds-lm3633.txt
[3] ../regulator/lm363x-regulator.txt
-lm3532@38 {
- compatible = "ti,lm3532";
- reg = <0x38>;
-
- enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;
-
- backlight {
- compatible = "ti,lm3532-backlight";
-
- lcd {
- led-sources = <0 1 2>;
- ramp-up-msec = <30>;
- ramp-down-msec = <0>;
- };
- };
-};
-
lm3631@29 {
compatible = "ti,lm3631";
reg = <0x29>;
--
2.20.1.390.gb5101f9297
