On Fri, Feb 01, 2019 at 01:32:35PM +0100, Johan Jonker wrote:
> This patch adds a binding that describes the HDMI controller for
> rk3066.
This is not using the DW block like other Rockchip SoCs (IIRC)?
>
> Signed-off-by: Johan Jonker <jbx6244@xxxxxxxxx>
> ---
> .../display/rockchip/rk3066_hdmi-rockchip.txt | 60 ++++++++++++++++++++++
Using the compatible string plus '.txt' is the preferred naming.
> 1 file changed, 60 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/rockchip/rk3066_hdmi-rockchip.txt
>
> diff --git a/Documentation/devicetree/bindings/display/rockchip/rk3066_hdmi-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/rk3066_hdmi-rockchip.txt
> new file mode 100644
> index 000000000..6a8f3754f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/rockchip/rk3066_hdmi-rockchip.txt
> @@ -0,0 +1,60 @@
> +Rockchip specific extensions for rk3066 HDMI
> +============================================
> +
> +Required properties:
> +- compatible:
> + "rockchip,rk3066-hdmi";
> +- reg:
> + Physical base address and length of the controller's registers.
> +- clocks, clock-names:
> + Phandle to HDMI controller clock, name should be "hclk".
> +- interrupts:
> + HDMI interrupt number.
> +- power-domains:
> + Phandle to the RK3066_PD_VIO power domain.
> +- rockchip,grf:
> + This soc uses GRF regs to switch the HDMI TX input between vop0 and vop1.
> +- ports:
> + Contains one port node with two endpoints, numbered 0 and 1,
> + connected respectively to vop0 and vop1.
You should have an output port to an hdmi-connector node (or bridge) as
well.
> +- pinctrl-0, pinctrl-name:
> + Switch the iomux for the HPD/I2C pins to HDMI function.
> +
> +Example:
> + hdmi: hdmi@10116000 {
> + compatible = "rockchip,rk3066-hdmi";
> + reg = <0x10116000 0x2000>;
> + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru HCLK_HDMI>;
> + clock-names = "hclk";
> + power-domains = <&power RK3066_PD_VIO>;
> + rockchip,grf = <&grf>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&hdmii2c_xfer>, <&hdmi_hpd>;
> + status = "disabled";
Don't show status in examples.
> +
> + hdmi_in: port {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + hdmi_in_vop0: endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&vop0_out_hdmi>;
> + };
> + hdmi_in_vop1: endpoint@1 {
> + reg = <1>;
> + remote-endpoint = <&vop1_out_hdmi>;
> + };
> + };
> + };
> +
> +&pinctrl {
> + hdmi {
> + hdmi_hpd: hdmi-hpd {
> + rockchip,pins = <0 RK_PA0 1 &pcfg_pull_default>;
> + };
> + hdmii2c_xfer: hdmii2c-xfer {
> + rockchip,pins = <0 RK_PA1 1 &pcfg_pull_none>,
> + <0 RK_PA2 1 &pcfg_pull_none>;
> + };
> + };
> +};
> --
> 2.11.0
>
