On Tue, 19 Feb 2019 15:55:10 +0000
Phil Edworthy <phil.edworthy@xxxxxxxxxxx> wrote:
> Add device binding documentation for the Renesas RZ/N1 GPIO interrupt
> multiplexer.
>
> Signed-off-by: Phil Edworthy <phil.edworthy@xxxxxxxxxxx>
> ---
> v4:
> - nits: hex mask and gpioirqmux@ ==> interrupt-controller@,
> gpio-controller@ ==> gpio@
> v3:
> - Use 'interrupt-map' DT property correctly.
> v2:
> - Use interrupt-map to allow the GPIO controller info to be specified
> as part of the irq.
> - Don't show status in binding examples.
> - Don't show the soc/board split in binding doc.
> ---
> .../interrupt-controller/renesas,rzn1-mux.txt | 73 +++++++++++++++++++
> 1 file changed, 73 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/interrupt-controller/renesas,rzn1-mux.txt
>
> diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,rzn1-mux.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,rzn1-mux.txt
> new file mode 100644
> index 000000000000..6a17324eef65
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,rzn1-mux.txt
> @@ -0,0 +1,73 @@
> +* Renesas RZ/N1 GPIO Interrupt Multiplexer
> +
> +On Renesas RZ/N1 devices, there are several GPIO Controllers each with a number
> +of interrupt outputs. All of the interrupts from the GPIO Controllers are passed
> +to the GPIO Interrupt Multiplexer, which selects a sub-set of the interrupts to
> +pass onto the system interrupt controller.
> +
> +A single node in the device tree is used to describe the GPIO IRQ Muxer.
> +
> +Required properties:
> +- compatible: SoC-specific compatible string "renesas,<soc-specific>-gpioirqmux"
> + followed by "renesas,rzn1-gpioirqmux" as fallback. The SoC-specific compatible
> + strings must be one of:
> + "renesas,r9a06g032-gpioirqmux" for RZ/N1D
> + "renesas,r9a06g033-gpioirqmux" for RZ/N1S
> +- reg: Base address and size of GPIO IRQ Muxer registers.
> +- interrupts: List of output interrupts.
> +- #interrupt-cells: Numder of cells in the input interrupt specifier, must be 1.
> +- #address-cells: Must be 0.
> +- interrupt-map-mask: must be 127.
> +- interrupt-map: Standard property detailing the maps between input irqs and the
> + corresponding output irq. This consist of a list of:
> + <input-irq-spec phandle-to-interrupt-controller output-irq-spec>
> + The input-irq-spec is from 0 to 95, corresponding to the outputs of the GPIO
> + Controllers.
> +
> +Example:
> +
> + The following is an example for the RZ/N1D SoC.
> +
> + gpioirqmux: interrupt-controller@51000480 {
> + compatible = "renesas,r9a06g032-gpioirqmux",
> + "renesas,rzn1-gpioirqmux";
> + reg = <0x51000480 0x20>;
> + interrupts =
> + <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
> +
> + #interrupt-cells = <1>;
> + #address-cells = <0>;
> + interrupt-map-mask = <0x7f>;
> + interrupt-map =
> + /* gpio2a 24, pin 146: ETH Port 1 IRQ */
> + <88 &gic GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
> + /* gpio2a 26, pin 148: TouchSCRN_IRQ */
> + <90 &gic GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
To complement my comments on patch #2, I find it extremely unusual that
the interrupt controller node contains the configuration for the
connected devices. This is contrary to the way we normally set these up.
I'd expect this interrupt-map not to exist at all, and devices to
simply have an interrupt-specifier.
> + };
> +
> + gpio2: gpio@5000d000 {
> + compatible = "snps,dw-apb-gpio";
> + reg = <0x5000d000 0x80>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clock-names = "bus";
> + clocks = <&sysctrl R9A06G032_HCLK_GPIO2>;
> +
> + gpio2a: gpio@0 {
> + compatible = "snps,dw-apb-gpio-port";
> + bank-name = "gpio2a";
> + gpio-controller;
> + #gpio-cells = <2>;
> + snps,nr-gpios = <32>;
> + reg = <0>;
> +
> + interrupt-controller;
> + interrupt-parent = <&gpioirqmux>;
> + interrupts = < 64 65 66 67 68 69 70 71
> + 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87
> + 88 89 90 91 92 93 94 95 >;
So we have 64 interrupts, only 2 that can actually be serviced? That
doesn't seem right.
> + #interrupt-cells = <2>;
> + };
> + };
M.
--
Without deviation from the norm, progress is not possible.
