On 19-02-14 18:32:40, Lucas Stach wrote:
> Am Donnerstag, den 14.02.2019, 18:26 +0100 schrieb Lucas Stach:
> > Am Donnerstag, den 14.02.2019, 17:18 +0000 schrieb Abel Vesa:
> > > On 19-02-14 16:50:28, Lucas Stach wrote:
> > > > Hi Abel
> > > >
> > > > Am Mittwoch, den 13.02.2019, 19:05 +0000 schrieb Abel Vesa:
> > > > > Add the opp table containing only non over drive opps.
> > > > > Also add the cpu-supply nodes for the A53 cores in the EVK
> > > > > board.
> > > > >
> > > > > Signed-off-by: Abel Vesa <abel.vesa@xxxxxxx>
> > > > > ---
> > > > > arch/arm64/boot/dts/freescale/imx8mq-evk.dts | 17
> > > > > +++++++++++++++++
> > > > > arch/arm64/boot/dts/freescale/imx8mq.dtsi | 23
> > > > > +++++++++++++++++++++++
> > > > > 2 files changed, 40 insertions(+)
> > > > >
> > > > > diff --git a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
> > > > > b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
> > > > > index 54737bf..114359e 100644
> > > > > --- a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
> > > > > +++ b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
> > > > > @@ -31,6 +31,23 @@
> > > > > gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> > > > > enable-active-high;
> > > > > };
> > > > > +
> > > > > +};
> > > > > +
> > > > > +&A53_0 {
> > > > > + cpu-supply = <&sw1a_reg>;
> > > > > +};
> > > > > +
> > > > > +&A53_1 {
> > > > > + cpu-supply = <&sw1a_reg>;
> > > > > +};
> > > > > +
> > > > > +&A53_2 {
> > > > > + cpu-supply = <&sw1a_reg>;
> > > > > +};
> > > > > +
> > > > > +&A53_3 {
> > > > > + cpu-supply = <&sw1a_reg>;
> > > > > };
> > > >
> > > > This should be a separate patch.
> > > >
> > >
> > > OK, will send as separate patches in the next version.
> > >
> > > > And AFAICS this is wrong, sw1a on the MX8M-EVK is the GPU supply,
> > > > the
> > > > CPU is supplied by a dedicated switcher that is controlled via a
> > > > GPIO.
> > > >
> > >
> > > Hmm, I think you're right. At least this is what the following
> > > document says.
> > >
> > > https://emea01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fwww.mouser.com%2Fds%2F2%2F302%2FIMX8MDQLQEVKHUG-1280333.pdf&data=02%7C01%7Cabel.vesa%40nxp.com%7Cf7666164aff84f6f975d08d692a26c2a%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C1%7C636857623628438873&sdata=EJJdfD8ewEXVQSTf2FqjEeUqGJd%2BwW94OQag428lszY%3D&reserved=0
> > >
> > > So I guess this means there will not be any cpu-supply properties.
> >
> > There is a variable voltage CPU supply, but you need to model it as a
> > gpio-regulator in the DT, it's not part of the PMIC provided rails.
>
> In the schematics it's the line called PWM_LED (actually it's just
> GPIO1_IO13) that controls the voltage. This changes the feedback of the
> DCDC switcher, so it can toggle between 0.9V and 1.0V.
>
Thanks, will look into it tomorrow when I get back at the office.
> Regards,
> Lucas
