On Mon, 2019-01-07 at 14:22 +0100, Stefan Agner wrote: > Allow to use DMA for SPI by adding the appropriate DMA properites > to the ecspi nodes. > > Signed-off-by: Stefan Agner <stefan@xxxxxxxx> > --- > arch/arm/boot/dts/imx7s.dtsi | 8 ++++++++ > 1 file changed, 8 insertions(+) > > diff --git a/arch/arm/boot/dts/imx7s.dtsi b/arch/arm/boot/dts/imx7s.dtsi > index a052198f6e96..b9330176c3af 100644 > --- a/arch/arm/boot/dts/imx7s.dtsi > +++ b/arch/arm/boot/dts/imx7s.dtsi > @@ -653,6 +653,8 @@ > clocks = <&clks IMX7D_ECSPI4_ROOT_CLK>, > <&clks IMX7D_ECSPI4_ROOT_CLK>; > clock-names = "ipg", "per"; > + dmas = <&sdma 6 7 1>, <&sdma 7 7 2>; > + dma-names = "rx", "tx"; > status = "disabled"; > }; After updating my kernel to linux-next on my IMX7d based device, I found that an FPGA, which is programmed via the ECSPI interface, was no longer accepting its image. I tracked the problem to this change. If I turn off DMA, it works. There's an interesting thing that happens when DMA is used. The SPI clock changes. Instead of cycling continuously for the entire transfer, it instead clocks out 8 bits, then pauses for 4 bit times, then the next byte, etc. So it's a net of about 50% slower. The pause between bytes scales with spi frequency to always be about 4 bits. Here's a trace with DMA: https://imagebin.ca/v/4WEkEnvsVSkq Here's what it looks like without DMA: https://imagebin.ca/v/4WEkVfEqpQ12 It seems like there are other problems with DMA too. Here's an error I'll random get every so often. [ 142.082325] spi_master spi1: I/O Error in DMA RX [ 142.085678] spidev spi1.0: SPI transfer failed: -110 [ 142.089389] spi_master spi1: failed to transfer one message from queue Not sure if the timeout is overly aggressive or if there is some other failure. Then sometimes there errors are worse: Internal error: Oops - undefined instruction: 0 [#1] PREEMPT SMP ARM Modules linked in: CPU: 0 PID: 1006 Comm: fpga-loader Not tainted 5.0.0-rc4-next-20190201 #1 Hardware name: Freescale i.MX7 Dual (Device Tree) PC is at sg_last+0x4c/0x68 LR is at (null) pc : [<80494800>] lr : [<00000000>] psr: 60010013 sp : bf0add5c ip : bea94598 fp : bf371218 r10: bf0949f0 r9 : 00000000 r8 : bf094800 r7 : bdc39300 r6 : bf371000 r5 : bdc39300 r4 : bf094b68 r3 : 00000000 r2 : 00000001 r1 : 00000001 r0 : bea94580 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 30c5387d Table: bea94000 DAC: fffffffd Process fpga-loader (pid: 1006, stack limit = 0x61bc8b73) Stack: (0xbf0add5c to 0xbf0ae000) dd40: 8056cdb0 dd60: 8056c9ac 00001000 00000000 bdc39300 bf094800 bf094b68 bf371000 00000000 dd80: bf0949f0 8056bc00 bf094800 bdc39300 bf0adeac bf094800 bf094ad0 80569edc ... dfc0: 00217301 00150000 00001000 00000036 00df2010 00000003 00001000 00df1008 dfe0: 00022f70 7e9ebb14 000113b8 76f2a7f8 20010030 00000003 00000000 00000000 [<80494800>] (sg_last) from [<8056cdb0>] (spi_imx_transfer+0xd8/0x448) [<8056cdb0>] (spi_imx_transfer) from [<8056bc00>] (spi_bitbang_transfer_one+0x50/0xa0) [<8056bc00>] (spi_bitbang_transfer_one) from [<80569edc>] (spi_transfer_one_message+0x18c/0x3e0) [<80569edc>] (spi_transfer_one_message) from [<8056a498>] (__spi_pump_messages+0x368/0x518) [<8056a498>] (__spi_pump_messages) from [<8056a7ec>] (__spi_sync+0x198/0x1a0) [<8056a7ec>] (__spi_sync) from [<8056a818>] (spi_sync+0x24/0x3c) [<8056a818>] (spi_sync) from [<8056ae14>] (spidev_sync+0x38/0x4c) [<8056ae14>] (spidev_sync) from [<8056b6f4>] (spidev_ioctl+0x660/0x704) [<8056b6f4>] (spidev_ioctl) from [<80335f9c>] (do_vfs_ioctl+0xac/0x79c) [<80335f9c>] (do_vfs_ioctl) from [<803366c0>] (ksys_ioctl+0x34/0x58) [<803366c0>] (ksys_ioctl) from [<80201120>] (ret_fast_syscall+0x0/0x4c) Exception stack(0xbf0adfa8 to 0xbf0adff0) dfa0: 00217301 00150000 00000003 40206b00 7e9ebb80 03938700 dfc0: 00217301 00150000 00001000 00000036 00df2010 00000003 00001000 00df1008 dfe0: 00022f70 7e9ebb14 000113b8 76f2a7f8 Code: e1510002 1afffff3 e3530000 149df004 (e7f001f2) ---[ end trace 1588229fc7541669 ]--- I think DMA on imx not be ready for prime time yet.
