Hi Paul,
Paul Cercueil <paul@xxxxxxxxxxxxxxx> wrote on Mon, 4 Feb 2019 16:04:24
-0300:
> Add support for probing the ingenic-nand driver on the JZ4740 SoC from
> Ingenic, and the jz4740-ecc driver to support the JZ4740-specific
> ECC hardware.
>
> Signed-off-by: Paul Cercueil <paul@xxxxxxxxxxxxxxx>
> ---
>
> Changes:
>
> v2: New patch
>
> v3: Also add support for the hardware ECC of the JZ4740 in this patch
>
> drivers/mtd/nand/raw/ingenic/Kconfig | 10 ++
> drivers/mtd/nand/raw/ingenic/Makefile | 1 +
> drivers/mtd/nand/raw/ingenic/ingenic_nand.c | 48 +++++--
> drivers/mtd/nand/raw/ingenic/jz4740_ecc.c | 192 ++++++++++++++++++++++++++++
> 4 files changed, 240 insertions(+), 11 deletions(-)
> create mode 100644 drivers/mtd/nand/raw/ingenic/jz4740_ecc.c
>
> diff --git a/drivers/mtd/nand/raw/ingenic/Kconfig b/drivers/mtd/nand/raw/ingenic/Kconfig
> index 4bf7d7af3b0a..cc663cc15119 100644
> --- a/drivers/mtd/nand/raw/ingenic/Kconfig
> +++ b/drivers/mtd/nand/raw/ingenic/Kconfig
> @@ -17,6 +17,16 @@ if MTD_NAND_JZ4780
> config MTD_NAND_INGENIC_ECC
> tristate
>
> +config MTD_NAND_JZ4740_ECC
> + tristate "Hardware BCH support for JZ4740 SoC"
> + select MTD_NAND_INGENIC_ECC
> + help
> + Enable this driver to support the Reed-Solomon error-correction
> + hardware present on the JZ4740 SoC from Ingenic.
> +
> + This driver can also be built as a module. If so, the module
> + will be called jz4740-ecc.
> +
> config MTD_NAND_JZ4780_BCH
> tristate "Hardware BCH support for JZ4780 SoC"
> select MTD_NAND_INGENIC_ECC
> diff --git a/drivers/mtd/nand/raw/ingenic/Makefile b/drivers/mtd/nand/raw/ingenic/Makefile
> index f3c3c0f230b0..563b7effcf59 100644
> --- a/drivers/mtd/nand/raw/ingenic/Makefile
> +++ b/drivers/mtd/nand/raw/ingenic/Makefile
> @@ -2,4 +2,5 @@ obj-$(CONFIG_MTD_NAND_JZ4740) += jz4740_nand.o
> obj-$(CONFIG_MTD_NAND_JZ4780) += ingenic_nand.o
>
> obj-$(CONFIG_MTD_NAND_INGENIC_ECC) += ingenic_ecc.o
> +obj-$(CONFIG_MTD_NAND_JZ4740_ECC) += jz4740_ecc.o
> obj-$(CONFIG_MTD_NAND_JZ4780_BCH) += jz4780_bch.o
> diff --git a/drivers/mtd/nand/raw/ingenic/ingenic_nand.c b/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
> index 0f51fd15fe79..3fd078920b17 100644
> --- a/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
> +++ b/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
> @@ -13,6 +13,7 @@
> #include <linux/module.h>
> #include <linux/of.h>
> #include <linux/of_address.h>
> +#include <linux/of_device.h>
> #include <linux/gpio/consumer.h>
> #include <linux/platform_device.h>
> #include <linux/slab.h>
> @@ -26,13 +27,15 @@
>
> #define DRV_NAME "ingenic-nand"
>
> -#define OFFSET_DATA 0x00000000
> -#define OFFSET_CMD 0x00400000
> -#define OFFSET_ADDR 0x00800000
> -
> /* Command delay when there is no R/B pin. */
> #define RB_DELAY_US 100
>
> +struct jz_soc_info {
> + unsigned long data_offset;
> + unsigned long addr_offset;
> + unsigned long cmd_offset;
> +};
> +
> struct ingenic_nand_cs {
> unsigned int bank;
> void __iomem *base;
> @@ -41,6 +44,7 @@ struct ingenic_nand_cs {
> struct ingenic_nfc {
> struct device *dev;
> struct ingenic_ecc *ecc;
> + const struct jz_soc_info *soc_info;
> struct nand_controller controller;
> unsigned int num_banks;
> struct list_head chips;
> @@ -100,9 +104,9 @@ static void ingenic_nand_cmd_ctrl(struct nand_chip *chip, int cmd,
> return;
>
> if (ctrl & NAND_ALE)
> - writeb(cmd, cs->base + OFFSET_ADDR);
> + writeb(cmd, cs->base + nfc->soc_info->addr_offset);
> else if (ctrl & NAND_CLE)
> - writeb(cmd, cs->base + OFFSET_CMD);
> + writeb(cmd, cs->base + nfc->soc_info->cmd_offset);
> }
>
> static int ingenic_nand_dev_ready(struct nand_chip *chip)
> @@ -160,8 +164,13 @@ static int ingenic_nand_attach_chip(struct nand_chip *chip)
> struct ingenic_nfc *nfc = to_ingenic_nfc(chip->controller);
> int eccbytes;
>
> - chip->ecc.bytes = fls((1 + 8) * chip->ecc.size) *
> - (chip->ecc.strength / 8);
> + if (chip->ecc.strength == 4) {
> + /* JZ4740 uses 9 bytes of ECC to correct maximum 4 errors */
> + chip->ecc.bytes = 9;
> + } else {
> + chip->ecc.bytes = fls((1 + 8) * chip->ecc.size) *
> + (chip->ecc.strength / 8);
> + }
>
> switch (chip->ecc.mode) {
> case NAND_ECC_HW:
> @@ -270,8 +279,8 @@ static int ingenic_nand_init_chip(struct platform_device *pdev,
> return -ENOMEM;
> mtd->dev.parent = dev;
>
> - chip->legacy.IO_ADDR_R = cs->base + OFFSET_DATA;
> - chip->legacy.IO_ADDR_W = cs->base + OFFSET_DATA;
> + chip->legacy.IO_ADDR_R = cs->base + nfc->soc_info->data_offset;
> + chip->legacy.IO_ADDR_W = cs->base + nfc->soc_info->data_offset;
> chip->legacy.chip_delay = RB_DELAY_US;
> chip->options = NAND_NO_SUBPAGE_WRITE;
> chip->legacy.select_chip = ingenic_nand_select_chip;
> @@ -353,6 +362,10 @@ static int ingenic_nand_probe(struct platform_device *pdev)
> if (!nfc)
> return -ENOMEM;
>
> + nfc->soc_info = device_get_match_data(dev);
> + if (!nfc->soc_info)
> + return -EINVAL;
> +
> /*
> * Check for ECC HW before we call nand_scan_ident, to prevent us from
> * having to call it again if the ECC driver returns -EPROBE_DEFER.
> @@ -390,8 +403,21 @@ static int ingenic_nand_remove(struct platform_device *pdev)
> return 0;
> }
>
> +static const struct jz_soc_info jz4740_soc_info = {
> + .data_offset = 0x00000000,
> + .cmd_offset = 0x00008000,
Please don't align ^
> + .addr_offset = 0x00010000,
> +};
> +
> +static const struct jz_soc_info jz4780_soc_info = {
> + .data_offset = 0x00000000,
> + .cmd_offset = 0x00400000,
> + .addr_offset = 0x00800000,
> +};
> +
> static const struct of_device_id ingenic_nand_dt_match[] = {
> - { .compatible = "ingenic,jz4780-nand" },
> + { .compatible = "ingenic,jz4740-nand", .data = &jz4740_soc_info },
> + { .compatible = "ingenic,jz4780-nand", .data = &jz4780_soc_info },
Just an extra space ^
Otherwise looks fine.
Thanks,
Miquèl
