On 1/26/19 12:17 PM, Jonathan Cameron wrote:
On Mon, 21 Jan 2019 18:04:27 -0800 Martin Kelly <martin@xxxxxxxxxxxxxxxx> wrote:From: Martin Kelly <martin@xxxxxxxxxxxxxxxx> Add interrupt support for the data ready signal on the BMI160, which fires an interrupt whenever new accelerometer/gyroscope data is ready to read. Signed-off-by: Martin Kelly <martin@xxxxxxxxxxxxxxxx>Various minor bits inline. I would also, if possible like Daniel to take a glance at this series before we apply it. I don't know this hardware at all well! Jonathan--- v2: - Drop "BOTH" interrupt setting. - Change to "if (ret)" instead of "if (ret < 0)". - Stylistic changes suggested by Jonathan Cameron. - Fix bogus return check after iio_trigger_get. arch/arm/boot/dts/Makefile | 1 + drivers/iio/imu/bmi160/bmi160.h | 13 +- drivers/iio/imu/bmi160/bmi160_core.c | 294 ++++++++++++++++++++++++++++++++++- drivers/iio/imu/bmi160/bmi160_i2c.c | 3 +- drivers/iio/imu/bmi160/bmi160_spi.c | 2 +- 5 files changed, 303 insertions(+), 10 deletions(-) diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index b0e966d625b9..df68910fc2c1 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -701,6 +701,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \ am335x-base0033.dtb \ am335x-bone.dtb \ am335x-boneblack.dtb \ + am335x-boneblack-bmi160-i2c1.dtb \Separate patch for this.
Oops, this wasn't intended to be there at all; it's an accidental carry-over from my testing that should not be checked in. I'll remove it.
am335x-boneblack-wireless.dtb \ am335x-boneblue.dtb \ am335x-bonegreen.dtb \ diff --git a/drivers/iio/imu/bmi160/bmi160.h b/drivers/iio/imu/bmi160/bmi160.h index 2351049d930b..0c5e67e0d35b 100644 --- a/drivers/iio/imu/bmi160/bmi160.h +++ b/drivers/iio/imu/bmi160/bmi160.h @@ -2,9 +2,20 @@ #ifndef BMI160_H_ #define BMI160_H_ +#include <linux/iio/iio.h> + +struct bmi160_data { + struct regmap *regmap; + struct iio_trigger *trig; +}; + extern const struct regmap_config bmi160_regmap_config; int bmi160_core_probe(struct device *dev, struct regmap *regmap, - const char *name, bool use_spi); + const char *name, bool use_spi, int irq); + +int bmi160_enable_irq(struct regmap *regmap, bool enable); + +int bmi160_probe_trigger(struct iio_dev *indio_dev, int irq, u32 irq_type); #endif /* BMI160_H_ */ diff --git a/drivers/iio/imu/bmi160/bmi160_core.c b/drivers/iio/imu/bmi160/bmi160_core.c index ce61026d84c3..c848fc1bce61 100644 --- a/drivers/iio/imu/bmi160/bmi160_core.c +++ b/drivers/iio/imu/bmi160/bmi160_core.c @@ -3,21 +3,25 @@ * BMI160 - Bosch IMU (accel, gyro plus external magnetometer) * * Copyright (c) 2016, Intel Corporation. + * Copyright (c) 2019, Martin Kelly. * * IIO core driver for BMI160, with support for I2C/SPI busses * - * TODO: magnetometer, interrupts, hardware FIFO + * TODO: magnetometer, hardware FIFO */ #include <linux/module.h> #include <linux/regmap.h> #include <linux/acpi.h> #include <linux/delay.h> +#include <linux/irq.h> +#include <linux/of_irq.h> #include <linux/iio/iio.h> #include <linux/iio/triggered_buffer.h> #include <linux/iio/trigger_consumer.h> #include <linux/iio/buffer.h> #include <linux/iio/sysfs.h> +#include <linux/iio/trigger.h> #include "bmi160.h" @@ -61,8 +65,32 @@ #define BMI160_CMD_GYRO_PM_FAST_STARTUP 0x17 #define BMI160_CMD_SOFTRESET 0xB6 +#define BMI160_REG_INT_EN 0x51 +#define BMI160_DRDY_INT_EN BIT(4) + +#define BMI160_REG_INT_OUT_CTRL 0x53 +#define BMI160_INT_OUT_CTRL_MASK 0x0f +#define BMI160_INT1_OUT_CTRL_SHIFT 0 +#define BMI160_INT2_OUT_CTRL_SHIFT 4 +#define BMI160_LEVEL_TRIGGERED BIT(0) +#define BMI160_ACTIVE_HIGH BIT(1) +#define BMI160_OPEN_DRAIN BIT(2) +#define BMI160_OUTPUT_EN BIT(3) + +#define BMI160_REG_INT_LATCH 0x54 +#define BMI160_INT1_LATCH_MASK BIT(4) +#define BMI160_INT2_LATCH_MASK BIT(5) + +/* INT1 and INT2 are in the opposite order as in INT_OUT_CTRL! */ +#define BMI160_REG_INT_MAP 0x56 +#define BMI160_INT1_MAP_DRDY_EN 0x80 +#define BMI160_INT2_MAP_DRDY_EN 0x08 + #define BMI160_REG_DUMMY 0x7F +#define BMI160_NORMAL_WRITE_USLEEP 2 +#define BMI160_SUSPENDED_WRITE_USLEEP 450 + #define BMI160_ACCEL_PMU_MIN_USLEEP 3800 #define BMI160_GYRO_PMU_MIN_USLEEP 80000 #define BMI160_SOFTRESET_USLEEP 1000 @@ -105,8 +133,9 @@ enum bmi160_sensor_type { BMI160_NUM_SENSORS /* must be last */ }; -struct bmi160_data { - struct regmap *regmap; +enum bmi160_int_pin { + BMI160_PIN_INT1, + BMI160_PIN_INT2 }; const struct regmap_config bmi160_regmap_config = { @@ -495,7 +524,209 @@ static const char *bmi160_match_acpi_device(struct device *dev) return dev_name(dev); } -static int bmi160_chip_init(struct bmi160_data *data, bool use_spi) +static int bmi160_write_conf_reg(struct regmap *regmap, unsigned int reg, + unsigned int mask, unsigned int bits, + unsigned int write_usleep) +{ + int ret; + unsigned int val; + + ret = regmap_read(regmap, reg, &val); + if (ret) + return ret; + + val = (val & ~mask) | bits; + + ret = regmap_write(regmap, reg, val); + if (ret) + return ret; + + /* + * We need to wait after writing before we can write again. See the + * datasheet, page 93. + */ + usleep_range(write_usleep, write_usleep + 1000); + + return 0; +} + +static int bmi160_config_pin(struct regmap *regmap, enum bmi160_int_pin pin, + bool open_drain, u8 irq_mask, + unsigned long write_usleep) +{ + int ret; + u8 int_out_ctrl_shift; + u8 int_latch_mask; + u8 int_map_mask; + u8 int_out_ctrl_mask; + u8 int_out_ctrl_bits; + + switch (pin) { + case BMI160_PIN_INT1: + int_out_ctrl_shift = BMI160_INT1_OUT_CTRL_SHIFT; + int_latch_mask = BMI160_INT1_LATCH_MASK; + int_map_mask = BMI160_INT1_MAP_DRDY_EN; + break; + case BMI160_PIN_INT2: + int_out_ctrl_shift = BMI160_INT2_OUT_CTRL_SHIFT; + int_latch_mask = BMI160_INT2_LATCH_MASK; + int_map_mask = BMI160_INT2_MAP_DRDY_EN; + break; + } + int_out_ctrl_mask = BMI160_INT_OUT_CTRL_MASK << int_out_ctrl_shift; + + /* + * Enable the requested pin with the right settings: + * - Push-pull/open-drain + * - Active low/high + * - Edge/level triggered + */ + int_out_ctrl_bits = BMI160_OUTPUT_EN; + if (open_drain) + /* Default is push-pull. */ + int_out_ctrl_bits |= BMI160_OPEN_DRAIN; + int_out_ctrl_bits |= irq_mask; + int_out_ctrl_bits <<= int_out_ctrl_shift; + + ret = bmi160_write_conf_reg(regmap, BMI160_REG_INT_OUT_CTRL, + int_out_ctrl_mask, int_out_ctrl_bits, + write_usleep); + if (ret) + return ret; + + /* Set the pin to input mode with no latching. */ + ret = bmi160_write_conf_reg(regmap, BMI160_REG_INT_LATCH, + int_latch_mask, int_latch_mask, + write_usleep); + if (ret) + return ret; + + /* Map interrupts to the requested pin. */ + ret = bmi160_write_conf_reg(regmap, BMI160_REG_INT_MAP, + int_map_mask, int_map_mask, + write_usleep); + if (ret) + return ret;return bmi160...+ + return 0; +} + +int bmi160_enable_irq(struct regmap *regmap, bool enable) +{ + unsigned int enable_bit = 0; + + if (enable) + enable_bit = BMI160_DRDY_INT_EN; + + return bmi160_write_conf_reg(regmap, BMI160_REG_INT_EN, + BMI160_DRDY_INT_EN, enable_bit, + BMI160_NORMAL_WRITE_USLEEP); +} +EXPORT_SYMBOL(bmi160_enable_irq); + +static bool bmi160_parse_irqname(struct device_node *of_node, int irq, + enum bmi160_int_pin *pin) +{ + int ret; + + /* of_irq_get_byname returns the IRQ number if the entry is found. */ + ret = of_irq_get_byname(of_node, "INT1"); + if (ret == irq) { + *pin = BMI160_PIN_INT1; + return true; + }Given both could be provided, and we are implying a preference, why not just get INT1 first by name and if it's not there try for INT2? No need for this separate does the name match query.
I actually didn't mean to imply a preference; I just figured that a given IRQ can have only one name, and therefore at most one of the names "INT1" and "INT2" will match the passed-in IRQ. Is this a bad assumption?
+ + ret = of_irq_get_byname(of_node, "INT2"); + if (ret == irq) { + *pin = BMI160_PIN_INT2; + return true; + } + + return false; +} + +static int bmi160_config_device_irq(struct iio_dev *indio_dev, + int irq, int irq_type) +{ + int ret; + bool success; + enum bmi160_int_pin int_pin; + bool open_drain; + const char *pin_name; + u8 irq_mask; + struct bmi160_data *data = iio_priv(indio_dev); + struct device *dev = regmap_get_device(data->regmap); + + /* Edge-triggered, active-low is the default if we set all zeroes. */ + if (irq_type == IRQF_TRIGGER_RISING) + irq_mask = BMI160_ACTIVE_HIGH | BMI160_LEVEL_TRIGGERED;That seems unlikely. Why on a rising trigger are we setting a flag that is named to imply it sets level triggering?
I will double-check the datasheet, but I think this is a mistake and I should swap the RISING and HIGH cases.
+ else if (irq_type == IRQF_TRIGGER_FALLING) + irq_mask = BMI160_LEVEL_TRIGGERED; + else if (irq_type == IRQF_TRIGGER_HIGH) + irq_mask = BMI160_ACTIVE_HIGH; + else if (irq_type == IRQF_TRIGGER_LOW) + irq_mask = 0; + else { + dev_err(&indio_dev->dev, + "Invalid interrupt type 0x%x specified\n", irq_type); + return -EINVAL; + } + + success = bmi160_parse_irqname(dev->of_node, irq, &int_pin); + if (!success) { + dev_err(&indio_dev->dev, + "interrupt-names for IRQ %d must be set to either \"INT1\" or \"INT2\"", + irq); + return -EINVAL; + } + + open_drain = of_property_read_bool(dev->of_node, "bmi160,open-drain"); + + ret = bmi160_config_pin(data->regmap, int_pin, open_drain, irq_mask, + BMI160_NORMAL_WRITE_USLEEP); + if (ret) { + switch (int_pin) { + case BMI160_PIN_INT1: + pin_name = "INT1"; + break; + case BMI160_PIN_INT2: + pin_name = "INT2"; + break; + } + dev_err(&indio_dev->dev, "Failed to configure %s IRQ pin", + pin_name);Why not do that within bmi160_config_pin? Then we have return bmi160_config_pin..
Yeah, I'll move this into bmi160_config_pin.
+ return ret; + } + + return 0; +} + +static int bmi160_setup_irq(struct iio_dev *indio_dev, int irq) +{ + struct irq_data *desc; + u32 irq_type; + int ret; + + desc = irq_get_irq_data(irq); + if (!desc) { + dev_warn(&indio_dev->dev, "Could not find IRQ %d\n", irq); + return -EINVAL; + } + + irq_type = irqd_get_trigger_type(desc); + + ret = bmi160_config_device_irq(indio_dev, irq, irq_type); + if (ret) + return ret; + + ret = bmi160_probe_trigger(indio_dev, irq, irq_type); + if (ret) + return ret;return bmi160_probe_trigger... It's either zero or it's not. Either way this gives the same as you have here.+ + return 0; +} + +static int bmi160_chip_init(struct bmi160_data *data, bool use_spi, int irq) { int ret; unsigned int val; @@ -518,7 +749,7 @@ static int bmi160_chip_init(struct bmi160_data *data, bool use_spi) } ret = regmap_read(data->regmap, BMI160_REG_CHIP_ID, &val); - if (ret < 0) { + if (ret) {This should be a separate patch, not rolled in here. It's a good cleanup but within this patch it's noise.
Good catch, I tried to separate the cleanup changes but I missed this one. I will move it.
dev_err(dev, "Error reading chip id\n"); return ret; } @@ -539,6 +770,49 @@ static int bmi160_chip_init(struct bmi160_data *data, bool use_spi) return 0; } +static int bmi160_data_rdy_trigger_set_state(struct iio_trigger *trig, + bool enable) +{ + struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig); + struct bmi160_data *data = iio_priv(indio_dev); + + return bmi160_enable_irq(data->regmap, enable); +} + +static const struct iio_trigger_ops bmi160_trigger_ops = { + .set_trigger_state = &bmi160_data_rdy_trigger_set_state, +}; + +int bmi160_probe_trigger(struct iio_dev *indio_dev, int irq, u32 irq_type) +{ + struct bmi160_data *data = iio_priv(indio_dev); + int ret; + + data->trig = devm_iio_trigger_alloc(&indio_dev->dev, "%s-dev%d", + indio_dev->name, indio_dev->id); + + if (data->trig == NULL) + return -ENOMEM; + + ret = devm_request_irq(&indio_dev->dev, irq, + &iio_trigger_generic_data_rdy_poll, + irq_type, "bmi160", data->trig); + if (ret < 0) + return ret; + + data->trig->dev.parent = regmap_get_device(data->regmap); + data->trig->ops = &bmi160_trigger_ops; + iio_trigger_set_drvdata(data->trig, indio_dev); + + ret = devm_iio_trigger_register(&indio_dev->dev, data->trig); + if (ret) + return ret; + + indio_dev->trig = iio_trigger_get(data->trig); + + return 0; +} + static void bmi160_chip_uninit(void *data) { struct bmi160_data *bmi_data = data; @@ -548,7 +822,7 @@ static void bmi160_chip_uninit(void *data) } int bmi160_core_probe(struct device *dev, struct regmap *regmap, - const char *name, bool use_spi) + const char *name, bool use_spi, int irq) { struct iio_dev *indio_dev; struct bmi160_data *data; @@ -562,7 +836,7 @@ int bmi160_core_probe(struct device *dev, struct regmap *regmap, dev_set_drvdata(dev, indio_dev); data->regmap = regmap; - ret = bmi160_chip_init(data, use_spi); + ret = bmi160_chip_init(data, use_spi, irq); if (ret < 0) return ret; @@ -585,6 +859,12 @@ int bmi160_core_probe(struct device *dev, struct regmap *regmap, if (ret < 0) return ret; + if (irq) { + ret = bmi160_setup_irq(indio_dev, irq); + if (ret) + return ret; + } + ret = devm_iio_device_register(dev, indio_dev); if (ret < 0) return ret; diff --git a/drivers/iio/imu/bmi160/bmi160_i2c.c b/drivers/iio/imu/bmi160/bmi160_i2c.c index e36f5e82d400..98467d73c887 100644 --- a/drivers/iio/imu/bmi160/bmi160_i2c.c +++ b/drivers/iio/imu/bmi160/bmi160_i2c.c @@ -32,7 +32,8 @@ static int bmi160_i2c_probe(struct i2c_client *client, if (id) name = id->name; - return bmi160_core_probe(&client->dev, regmap, name, false); + return bmi160_core_probe(&client->dev, regmap, + name, false, client->irq); } static const struct i2c_device_id bmi160_i2c_id[] = { diff --git a/drivers/iio/imu/bmi160/bmi160_spi.c b/drivers/iio/imu/bmi160/bmi160_spi.c index c19e3df35559..23e323518873 100644 --- a/drivers/iio/imu/bmi160/bmi160_spi.c +++ b/drivers/iio/imu/bmi160/bmi160_spi.c @@ -24,7 +24,7 @@ static int bmi160_spi_probe(struct spi_device *spi) (int)PTR_ERR(regmap)); return PTR_ERR(regmap); } - return bmi160_core_probe(&spi->dev, regmap, id->name, true); + return bmi160_core_probe(&spi->dev, regmap, id->name, true, spi->irq); } static const struct spi_device_id bmi160_spi_id[] = { -- 2.11.0
