On 12:01-20190111, Roger Quadros wrote:
> Adds support for USB0 and USB1 instances on the AM6 SoC.
> USB0 is limited to high-speed for now.
>
> Signed-off-by: Roger Quadros <rogerq@xxxxxx>
> ---
> arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 80 ++++++++++++++++++++++++++++++++
> 1 file changed, 80 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> index 8b55108..680cbc7 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> @@ -199,4 +199,84 @@
> #size-cells = <1>;
> ranges = <0x0 0x0 0x00100000 0x1c000>;
> };
> +
> + dwc3_0: dwc3@4000000 {
> + compatible = "ti,am654-dwc3";
> + reg = <0x0 0x4000000 0x0 0x4000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0x0 0x0 0x4000000 0x20000>;
> + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
> + dma-coherent;
> + status = "disabled";
NAK. -> in ARMV8, we dont do default disabled. Instead, please disable
nodes in the board dts or overlay as necessary.
> + power-domains = <&k3_pds 151>;
> + assigned-clocks = <&k3_clks 151 2>, <&k3_clks 151 7>;
> + assigned-clock-parents = <&k3_clks 151 4>, /* set REF_CLK to 20MHz i.e. PER0_PLL/48 */
> + <&k3_clks 151 9>; /* set PIPE3_TXB_CLK to CLK_12M_RC/256 (for HS only) */
> +
> + usb0: usb@10000 {
> + compatible = "snps,dwc3";
> + reg = <0x10000 0x10000>;
> + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "peripheral",
> + "host",
> + "otg";
> + maximum-speed = "high-speed";
> + dr_mode = "otg";
> + phys = <&usb0_phy>;
> + phy-names = "usb2-phy";
> + snps,dis_u3_susphy_quirk;
> + };
> + };
> +
> + usb0_phy: phy@4100000 {
> + compatible = "ti,am654-usb2", "ti,omap-usb2";
> + reg = <0x0 0x4100000 0x0 0x54>;
> + syscon-phy-power = <&scm_conf 0x4000>;
Just curious, dont we need a power domain as well?
> + clocks = <&k3_clks 151 0>, <&k3_clks 151 1>;
> + clock-names = "wkupclk", "refclk";
> + #phy-cells = <0>;
> + status = "disabled";
same here -> please drop
> + };
> +
> + dwc3_1: dwc3@4020000 {
> + compatible = "ti,am654-dwc3";
> + reg = <0x0 0x4020000 0x0 0x4000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0x0 0x0 0x4020000 0x20000>;
> + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
> + dma-coherent;
> + status = "disabled";
same here -> please drop
> + power-domains = <&k3_pds 152>;
> + assigned-clocks = <&k3_clks 152 2>;
> + assigned-clock-parents = <&k3_clks 152 4>; /* set REF_CLK to 20MHz i.e. PER0_PLL/48 */
> +
> + usb1: usb@10000 {
> + compatible = "snps,dwc3";
> + reg = <0x10000 0x10000>;
> + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "peripheral",
> + "host",
> + "otg";
> + maximum-speed = "high-speed";
> + dr_mode = "otg";
> + phys = <&usb1_phy>;
> + phy-names = "usb2-phy";
> + };
> + };
> +
> + usb1_phy: phy@4110000 {
> + compatible = "ti,am654-usb2", "ti,omap-usb2";
> + reg = <0x0 0x4110000 0x0 0x54>;
> + syscon-phy-power = <&scm_conf 0x4020>;
Same question on power domain..
> + clocks = <&k3_clks 152 0>, <&k3_clks 152 1>;
> + clock-names = "wkupclk", "refclk";
> + #phy-cells = <0>;
> + status = "disabled";
same here -> please drop
> + };
> };
> --
> Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
> Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
>
--
Regards,
Nishanth Menon
