Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
Signed-off-by: Brian Masney <masneyb@xxxxxxxxxxxxx>
---
Changes since v1:
- Interrupts are now two cells instead of four cells.
- Drop unnecessary interrupts property.
arch/arm/boot/dts/qcom-pm8941.dtsi | 39 +++---------------------------
1 file changed, 3 insertions(+), 36 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom-pm8941.dtsi
index 2515c5c217ac..16e6b4272d16 100644
--- a/arch/arm/boot/dts/qcom-pm8941.dtsi
+++ b/arch/arm/boot/dts/qcom-pm8941.dtsi
@@ -64,42 +64,9 @@
reg = <0xc000>;
gpio-controller;
#gpio-cells = <2>;
- interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
- <0 0xc1 0 IRQ_TYPE_NONE>,
- <0 0xc2 0 IRQ_TYPE_NONE>,
- <0 0xc3 0 IRQ_TYPE_NONE>,
- <0 0xc4 0 IRQ_TYPE_NONE>,
- <0 0xc5 0 IRQ_TYPE_NONE>,
- <0 0xc6 0 IRQ_TYPE_NONE>,
- <0 0xc7 0 IRQ_TYPE_NONE>,
- <0 0xc8 0 IRQ_TYPE_NONE>,
- <0 0xc9 0 IRQ_TYPE_NONE>,
- <0 0xca 0 IRQ_TYPE_NONE>,
- <0 0xcb 0 IRQ_TYPE_NONE>,
- <0 0xcc 0 IRQ_TYPE_NONE>,
- <0 0xcd 0 IRQ_TYPE_NONE>,
- <0 0xce 0 IRQ_TYPE_NONE>,
- <0 0xcf 0 IRQ_TYPE_NONE>,
- <0 0xd0 0 IRQ_TYPE_NONE>,
- <0 0xd1 0 IRQ_TYPE_NONE>,
- <0 0xd2 0 IRQ_TYPE_NONE>,
- <0 0xd3 0 IRQ_TYPE_NONE>,
- <0 0xd4 0 IRQ_TYPE_NONE>,
- <0 0xd5 0 IRQ_TYPE_NONE>,
- <0 0xd6 0 IRQ_TYPE_NONE>,
- <0 0xd7 0 IRQ_TYPE_NONE>,
- <0 0xd8 0 IRQ_TYPE_NONE>,
- <0 0xd9 0 IRQ_TYPE_NONE>,
- <0 0xda 0 IRQ_TYPE_NONE>,
- <0 0xdb 0 IRQ_TYPE_NONE>,
- <0 0xdc 0 IRQ_TYPE_NONE>,
- <0 0xdd 0 IRQ_TYPE_NONE>,
- <0 0xde 0 IRQ_TYPE_NONE>,
- <0 0xdf 0 IRQ_TYPE_NONE>,
- <0 0xe0 0 IRQ_TYPE_NONE>,
- <0 0xe1 0 IRQ_TYPE_NONE>,
- <0 0xe2 0 IRQ_TYPE_NONE>,
- <0 0xe3 0 IRQ_TYPE_NONE>;
+ interrupt-parent = <&spmi_bus>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
boost_bypass_n_pin: boost-bypass {
pins = "gpio21";
--
2.17.2
