From: Zhiyong Tao <zhiyong.tao@xxxxxxxxxxxx>
The commit adds mt8183 compatible node in binding document.
Signed-off-by: Zhiyong Tao <zhiyong.tao@xxxxxxxxxxxx>
Signed-off-by: Erin Lo <erin.lo@xxxxxxxxxxxx>
---
.../devicetree/bindings/pinctrl/pinctrl-mt8183.txt | 110 +++++++++++++++++++++
1 file changed, 110 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-mt8183.txt
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8183.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8183.txt
new file mode 100644
index 0000000..7b5285e
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8183.txt
@@ -0,0 +1,110 @@
+* Mediatek MT8183 Pin Controller
+
+The Mediatek's Pin controller is used to control SoC pins.
+
+Required properties:
+- compatible: value should be one of the following.
+ "mediatek,mt8183-pinctrl", compatible with mt8183 pinctrl.
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
+ binding is used, the amount of cells must be specified as 2. See the below
+ mentioned gpio binding representation for description of particular cells.
+- gpio-ranges : gpio valid number range.
+
+ Eg: <&pio 6 0>
+ <[phandle of the gpio controller node]
+ [line number within the gpio controller]
+ [flags]>
+
+ Values for gpio specifier:
+ - Line number: is a value between 0 to 202.
+ - Flags: bit field of flags, as defined in <dt-bindings/gpio/gpio.h>.
+ Only the following flags are supported:
+ 0 - GPIO_ACTIVE_HIGH
+ 1 - GPIO_ACTIVE_LOW
+
+Optional properties:
+- reg: physicall address base for gpio base registers.
+- reg-names: gpio base registers name.
+- interrupt-controller: Marks the device node as an interrupt controller
+- #interrupt-cells: Should be two.
+- interrupts : The interrupt outputs from the controller.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices.
+
+Subnode format
+A pinctrl node should contain at least one subnodes representing the
+pinctrl groups available on the machine. Each subnode will list the
+pins it needs, and how they should be configured, with regard to muxer
+configuration, pullups, drive strength, input enable/disable and input schmitt.
+
+ node {
+ pinmux = <PIN_NUMBER_PINMUX>;
+ GENERIC_PINCONFIG;
+ };
+
+Required properties:
+- pinmux: integer array, represents gpio pin number and mux setting.
+ Supported pin number and mux varies for different SoCs, and are defined
+ as macros in boot/dts/<soc>-pinfunc.h directly.
+
+Optional properties:
+- GENERIC_PINCONFIG: is the generic pinconfig options to use, bias-disable,
+ bias-pull-down, bias-pull-up, input-enable, input-disable, output-low, output-high,
+ input-schmitt-enable, input-schmitt-disable and drive-strength are valid.
+
+ Some special pins have extra pull up strength, there are R0 and R1 pull-up
+ resistors available, but for user, it's only need to set R1R0 as 00, 01, 10 or 11.
+ So when config mediatek,pull-up-adv or mediatek,pull-down-adv,
+ it support arguments for those special pins.
+
+ When config drive-strength, it can support some arguments, such as
+ MTK_DRIVE_4mA, MTK_DRIVE_6mA, etc. See dt-bindings/pinctrl/mt65xx.h.
+
+Examples:
+
+#include "mt8183-pinfunc.h"
+
+...
+{
+ pio: pinctrl@10005000 {
+ compatible = "mediatek,mt8183-pinctrl";
+ reg = <0 0x10005000 0 0x1000>,
+ <0 0x11F20000 0 0x1000>,
+ <0 0x11E80000 0 0x1000>,
+ <0 0x11E70000 0 0x1000>,
+ <0 0x11E90000 0 0x1000>,
+ <0 0x11D30000 0 0x1000>,
+ <0 0x11D20000 0 0x1000>,
+ <0 0x11C50000 0 0x1000>,
+ <0 0x11F30000 0 0x1000>;
+ reg-names = "iocfg0", "iocfg1", "iocfg2",
+ "iocfg3", "iocfg4", "iocfg5",
+ "iocfg6", "iocfg7", "iocfg8";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pio 0 0 192>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ #interrupt-cells = <2>;
+
+ i2c0_pins_a: i2c0@0 {
+ pins1 {
+ pinmux = <PINMUX_GPIO48__FUNC_SCL5>,
+ <PINMUX_GPIO49__FUNC_SDA5>;
+ mediatek,pull-up-adv = <11>;
+ };
+ };
+
+ i2c1_pins_a: i2c1@0 {
+ pins {
+ pinmux = <PINMUX_GPIO50__FUNC_SCL3>,
+ <PINMUX_GPIO51__FUNC_SDA3>;
+ mediatek,pull-down-adv = <10>;
+ };
+ };
+ ...
+ };
+};
--
1.9.1
