Add the DT binding documentation for Interrupt router driver. Signed-off-by: Lokesh Vutla <lokeshvutla@xxxxxx> --- .../interrupt-controller/ti,sci-intr.txt | 85 +++++++++++++++++++ MAINTAINERS | 1 + 2 files changed, 86 insertions(+) create mode 100644 Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt new file mode 100644 index 000000000000..4b0ca797fda1 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt @@ -0,0 +1,85 @@ +Texas Instruments K3 Interrupt Router +===================================== + +The Interrupt Router (INTR) module provides a mechanism to mux M +interrupt inputs to N interrupt outputs, where all M inputs are selectable +to be driven per N output. There is one register per output (MUXCNTL_N) that +controls the selection. + + + Interrupt Router + +----------------------+ + | Inputs Outputs | + +-------+ | +------+ | + | GPIO |----------->| | irq0 | | Host IRQ + +-------+ | +------+ | controller + | . +-----+ | +-------+ + +-------+ | . | 0 | |----->| IRQ | + | INTA |----------->| . +-----+ | +-------+ + +-------+ | . . | + | +------+ . | + | | irqM | +-----+ | + | +------+ | N | | + | +-----+ | + +----------------------+ + +Configuration of these MUXCNTL_N registers is done by a system controller +(like the Device Memory and Security Controller on K3 AM654 SoC). System +controller will keep track of the used and unused registers within the Router. +Driver should request the system controller to get the range of GIC IRQs +assigned to the requesting hosts. It is the drivers responsibility to keep +track of Host IRQs. + +Communication between the host processor running an OS and the system +controller happens through a protocol called TI System Control Interface +(TISCI protocol). For more details refer: +Documentation/devicetree/bindings/arm/keystone/ti,sci.txt + +TISCI Interrupt Router Node: +---------------------------- +- compatible: Must be "ti,sci-intr". +- interrupt-controller: Identifies the node as an interrupt controller +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt source. The value should be 4. + First cell should contain the TISCI device ID of source + Second cell should contain the interrupt source offset + within the device + Third cell specifies the trigger type as defined + in interrupts.txt in this directory. + Fourth cell should be 1 if the irq is coming from + interrupt aggregator else 0. +- ti,sci: Phandle to TI-SCI compatible System controller node. +- ti,sci-dst-id: TISCI device ID of the destination IRQ controller. +- ti,sci-rm-range-girq: Array of TISCI subtype ids representing the host irqs + assigned to this interrupt router. Each subtype id + corresponds to a range of host irqs. + +For more details on TISCI IRQ resource management refer: +http://downloads.ti.com/tisci/esd/latest/2_tisci_msgs/rm/rm_irq.html + +Example: +-------- +The following example demonstrates both interrupt router node and the consumer +node(main gpio) on the AM654 SoC: + +main_intr: interrupt-controller0 { + compatible = "ti,sci-intr"; + interrupt-controller; + interrupt-parent = <&gic500>; + #interrupt-cells = <4>; + ti,sci = <&dmsc>; + ti,sci-dst-id = <56>; + ti,sci-rm-range-girq = <0x1>; +}; + +main_gpio0: gpio@600000 { + ... + interrupt-parent = <&main_intr>; + interrupts = <57 256 IRQ_TYPE_EDGE_RISING 0>, + <57 257 IRQ_TYPE_EDGE_RISING 0>, + <57 258 IRQ_TYPE_EDGE_RISING 0>, + <57 259 IRQ_TYPE_EDGE_RISING 0>, + <57 260 IRQ_TYPE_EDGE_RISING 0>, + <57 261 IRQ_TYPE_EDGE_RISING 0>; + ... +}; diff --git a/MAINTAINERS b/MAINTAINERS index 82dc44b09a7e..8c7513b02d50 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -15023,6 +15023,7 @@ F: Documentation/devicetree/bindings/reset/ti,sci-reset.txt F: Documentation/devicetree/bindings/clock/ti,sci-clk.txt F: drivers/clk/keystone/sci-clk.c F: drivers/reset/reset-ti-sci.c +F: Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt Texas Instruments ASoC drivers M: Peter Ujfalusi <peter.ujfalusi@xxxxxx> -- 2.19.2
