On Tue, 18 Dec 2018, Christian Hohnstaedt wrote:
> These options apply to all regulators in this chip.
>
> strict-supply-voltage:
> Set STRICT flag in CONFIG1
> under-voltage-limit:
> Select 2.75, 2.95, 3.25 or 3.35 V UVLO in CONFIG1
> under-voltage-hysteresis:
> Select 200mV or 400mV UVLOHYS in CONFIG2
>
> Signed-off-by: Christian Hohnstaedt <Christian.Hohnstaedt@xxxxxxxx>
> ---
> drivers/mfd/tps65218.c | 46 ++++++++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 46 insertions(+)
This needs a close review by Tony and any of the other OMAP guys.
At the very least, please put '\n's between the if() statements. You
also need to return after an error print, else I suggest it's not an
error.
It would also look tidier if you changed the if()s to one liners to
assign to different variables, then dealt with them separately later
on. The way it's done here looks messy to say the least.
> diff --git a/drivers/mfd/tps65218.c b/drivers/mfd/tps65218.c
> index 8bcdecf..f5e559b 100644
> --- a/drivers/mfd/tps65218.c
> +++ b/drivers/mfd/tps65218.c
> @@ -211,6 +211,50 @@ static const struct of_device_id of_tps65218_match_table[] = {
> };
> MODULE_DEVICE_TABLE(of, of_tps65218_match_table);
>
> +static void tps65218_options(struct tps65218 *tps)
> +{
> + struct device *dev = tps->dev;
> + struct device_node *np = dev->of_node;
> + u32 pval;
What does pval mean? I suggest just val is more common.
> + if (!of_property_read_u32(np, "strict-supply-voltage", &pval)) {
> + tps65218_update_bits(tps, TPS65218_REG_CONFIG1,
> + TPS65218_CONFIG1_STRICT,
> + pval ? TPS65218_CONFIG1_STRICT : 0,
> + TPS65218_PROTECT_L1);
> + dev_dbg(dev, "tps65218 strict-supply-voltage: %d\n", pval);
> + }
> + if (!of_property_read_u32(np, "under-voltage-hysteresis", &pval)) {
> + if (pval != 400000 && pval != 200000) {
> + dev_err(dev,
> + "under-voltage-hysteresis must be %d or %d\n",
> + 200000, 400000);
> + } else {
> + tps65218_update_bits(tps, TPS65218_REG_CONFIG2,
> + TPS65218_CONFIG2_UVLOHYS,
> + pval == 400000 ? TPS65218_CONFIG2_UVLOHYS : 0,
> + TPS65218_PROTECT_L1);
> + }
> + dev_dbg(dev, "tps65218 under-voltage-hysteresis: %d\n", pval);
> + }
> + if (!of_property_read_u32(np, "under-voltage-limit", &pval)) {
> + int i, vals[] = { 275, 295, 325, 335 };
> +
> + for (i = 0; i < ARRAY_SIZE(vals); i++) {
> + if (pval == vals[i] * 10000)
Just use the full value in 'vals'.
> + break;
> + }
It took me a few seconds to realise what you're doing here.
I think a switch() statement would be cleaner.
You should also #define the values.
TPS65218_UNDER_VOLT_LIM_2750000 0
Etc.
> + if (i < ARRAY_SIZE(vals)) {
> + tps65218_update_bits(tps, TPS65218_REG_CONFIG1,
> + TPS65218_CONFIG1_UVLO_MASK, i,
> + TPS65218_PROTECT_L1);
> + } else {
> + dev_err(dev, "Invalid under-voltage-limit: %d\n", pval);
This could go in the default: section.
> + }
> + dev_dbg(dev, "tps65218 under-voltage-limit: %d=%d\n", pval, i);
I suggest considering removing these.
> + }
> +}
> +
> static int tps65218_probe(struct i2c_client *client,
> const struct i2c_device_id *ids)
> {
> @@ -249,6 +293,8 @@ static int tps65218_probe(struct i2c_client *client,
>
> tps->rev = chipid & TPS65218_CHIPID_REV_MASK;
>
> + tps65218_options(tps);
Options is not good nomenclature as it doesn't really tell us
anything. Looks like all the values are voltage related to me?
> ret = mfd_add_devices(tps->dev, PLATFORM_DEVID_AUTO, tps65218_cells,
> ARRAY_SIZE(tps65218_cells), NULL, 0,
> regmap_irq_get_domain(tps->irq_data));
--
Lee Jones [李琼斯]
Linaro Services Technical Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
