On 07/12/18 2:12 PM, Faiz Abbas wrote:
> On the am654x-evm, sdhci0 node is connected to an eMMC while sdhci1
> is connected to an SD card slot. Add nodes and pinmuxes for the same.
>
> Signed-off-by: Faiz Abbas <faiz_abbas@xxxxxx>
> ---
> .../arm64/boot/dts/ti/k3-am654-base-board.dts | 46 +++++++++++++++++++
> 1 file changed, 46 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> index bd5a0069191d..5dcd16b787eb 100644
> --- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> @@ -60,6 +60,36 @@
> AM65X_IOPAD(0x0070, PIN_INPUT, 5) /* (R25) GPMC0_CSn2.I2C2_SDA */
> >;
> };
> +
> + main_mmc0_pins_default: main_mmc0_pins_default {
make dtbs W=12 will warn you:
Character '_' not recommended in node name
> + pinctrl-single,pins = <
> + AM65X_IOPAD(0x01a8, PIN_INPUT_PULLDOWN, 0) /* (B25) MMC0_CLK */
> + AM65X_IOPAD(0x01ac, PIN_INPUT_PULLUP, 0) /* (B27) MMC0_CMD */
> + AM65X_IOPAD(0x01a4, PIN_INPUT_PULLUP, 0) /* (A26) MMC0_DAT0 */
> + AM65X_IOPAD(0x01a0, PIN_INPUT_PULLUP, 0) /* (E25) MMC0_DAT1 */
> + AM65X_IOPAD(0x019c, PIN_INPUT_PULLUP, 0) /* (C26) MMC0_DAT2 */
> + AM65X_IOPAD(0x0198, PIN_INPUT_PULLUP, 0) /* (A25) MMC0_DAT3 */
> + AM65X_IOPAD(0x0194, PIN_INPUT_PULLUP, 0) /* (E24) MMC0_DAT4 */
> + AM65X_IOPAD(0x0190, PIN_INPUT_PULLUP, 0) /* (A24) MMC0_DAT5 */
> + AM65X_IOPAD(0x018c, PIN_INPUT_PULLUP, 0) /* (B26) MMC0_DAT6 */
> + AM65X_IOPAD(0x0188, PIN_INPUT_PULLUP, 0) /* (D25) MMC0_DAT7 */
> + AM65X_IOPAD(0x01b4, PIN_INPUT_PULLUP, 0) /* (A23) MMC0_SDCD */
> + AM65X_IOPAD(0x01b0, PIN_INPUT, 0) /* (C25) MMC0_DS */
> + >;
> + };
> +
> + main_mmc1_pins_default: main_mmc1_pins_default {
Same here
Regards
Vignesh
> + pinctrl-single,pins = <
> + AM65X_IOPAD(0x02d4, PIN_INPUT_PULLDOWN, 0) /* (C27) MMC1_CLK */
> + AM65X_IOPAD(0x02d8, PIN_INPUT_PULLUP, 0) /* (C28) MMC1_CMD */
> + AM65X_IOPAD(0x02d0, PIN_INPUT_PULLUP, 0) /* (D28) MMC1_DAT0 */
> + AM65X_IOPAD(0x02cc, PIN_INPUT_PULLUP, 0) /* (E27) MMC1_DAT1 */
> + AM65X_IOPAD(0x02c8, PIN_INPUT_PULLUP, 0) /* (D26) MMC1_DAT2 */
> + AM65X_IOPAD(0x02c4, PIN_INPUT_PULLUP, 0) /* (D27) MMC1_DAT3 */
> + AM65X_IOPAD(0x02dc, PIN_INPUT_PULLUP, 0) /* (B24) MMC1_SDCD */
> + AM65X_IOPAD(0x02e0, PIN_INPUT, 0) /* (C24) MMC1_SDWP */
> + >;
> + };
> };
>
> &main_pmx1 {
> @@ -125,3 +155,19 @@
> pinctrl-0 = <&main_i2c2_pins_default>;
> clock-frequency = <400000>;
> };
> +
> +&sdhci0 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_mmc0_pins_default>;
> + bus-width = <8>;
> + non-removable;
> + ti,driver-strength-ohm = <50>;
> +};
> +
> +&sdhci1 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_mmc1_pins_default>;
> + ti,driver-strength-ohm = <50>;
> +};
>
--
Regards
Vignesh
