Hi,
On 2018/12/3 16:59, Sergei Shtylyov wrote:
> On 03.12.2018 11:51, Chen Yu wrote:
>
>>>> This patch adds binding descriptions to support the dwc3 controller
>>>> on HiSilicon SoCs and boards like the HiKey960.
>>>>
>>>> Cc: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
>>>> Cc: Rob Herring <robh+dt@xxxxxxxxxx>
>>>> Cc: Mark Rutland <mark.rutland@xxxxxxx>
>>>> Cc: John Stultz <john.stultz@xxxxxxxxxx>
>>>> Signed-off-by: Yu Chen <chenyu56@xxxxxxxxxx>
>>>> ---
>>>> .../devicetree/bindings/usb/dwc3-hisi.txt | 67 ++++++++++++++++++++++
>>>> 1 file changed, 67 insertions(+)
>>>> create mode 100644 Documentation/devicetree/bindings/usb/dwc3-hisi.txt
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/usb/dwc3-hisi.txt b/Documentation/devicetree/bindings/usb/dwc3-hisi.txt
>>>> new file mode 100644
>>>> index 000000000000..d32d2299a0a1
>>>> --- /dev/null
>>>> +++ b/Documentation/devicetree/bindings/usb/dwc3-hisi.txt
>>>> @@ -0,0 +1,67 @@
>>>> +HiSilicon DWC3 USB SoC controller
>>>> +
>>>> +This file documents the parameters for the dwc3-hisi driver.
>>>> +
>>>> +Required properties:
>>>> +- compatible: should be "hisilicon,hi3660-dwc3"
>>>> +- clocks: A list of phandle + clock-specifier pairs for the
>>>> + clocks listed in clock-names
>>>> +- clock-names: Specify clock names
>>>> +- resets: list of phandle and reset specifier pairs.
>>>> +
>>>> +Sub-nodes:
>>>> +The dwc3 core should be added as subnode to HiSilicon DWC3 as shown in the
>>>> +example below. The DT binding details of dwc3 can be found in:
>>>> +Documentation/devicetree/bindings/usb/dwc3.txt
>>>> +
>>>> +Example:
>>>> + usb3: hisi_dwc3 {
>>>> + compatible = "hisilicon,hi3660-dwc3";
>>>> + #address-cells = <2>;
>>>> + #size-cells = <2>;
>>>> + ranges;
>>>> +
>>>> + clocks = <&crg_ctrl HI3660_CLK_ABB_USB>,
>>>> + <&crg_ctrl HI3660_ACLK_GATE_USB3OTG>;
>>>> + clock-names = "clk_usb3phy_ref", "aclk_usb3otg";
>>>> + assigned-clocks = <&crg_ctrl HI3660_ACLK_GATE_USB3OTG>;
>>>> + assigned-clock-rates = <229000000>;
>>>> + resets = <&crg_rst 0x90 8>,
>>>> + <&crg_rst 0x90 7>,
>>>> + <&crg_rst 0x90 6>,
>>>> + <&crg_rst 0x90 5>;
>>>> +
>>>> + dwc3: dwc3@ff100000 {
>>>
>>> According to the DT spec, the node names should be generic, not chip specific, i.e. usb@ff100000 in this case.
>>>
>>
>> Do you mean it should be usb@ff100000: dwc3@ff100000 ?
>
> dwc3: usb@ff100000
>
> "dwc3:" is a label, not name.
I use the node name "dwc3@ff100000" according to Documentation/devicetree/bindings/usb/dwc3.txt
and documentations of vendor drivers, i.e. qcom,dwc3.txt, rockchip,dwc3.txt.
In these documentations, the dwc3 sub-node name uses "dwc3@xxxxxxxx".
I think it is better to be same as the other vendor's dwc3 drivers.
>
>> Thanks!
>>
>>> [...]
>
> MBR, Sergei
>
> .
>
