On Fri, Nov 23, 2018 at 03:15:11PM +0000, Vokáč Michal wrote: > On 22.11.2018 20:03, Uwe Kleine-König wrote: > > On Thu, Nov 22, 2018 at 04:46:39PM +0000, Vokáč Michal wrote: > >> On 22.11.2018 17:23, Uwe Kleine-König wrote: > >>> On Thu, Nov 22, 2018 at 03:42:14PM +0000, Vokáč Michal wrote: > >>>> On 16.11.2018 09:25, Uwe Kleine-König wrote: > >>>>> On Fri, Nov 16, 2018 at 08:34:30AM +0100, Lothar Waßmann wrote: > >>>>>> No. You can disable the output driver via pinctrl, so that only the > >>>>>> selected pull-up/down is relevant. The pin function and GPIO register > >>>>>> settings don't matter at all in this case. > >>>> > >>>> Lothar, please can you be more specific how would you do that? IFAIK the > >>>> pull-up/down internal resistors have effect only if the pin is configured > >>>> as GPIO *input* (on i.MX6 at least). See the TRM, 29.4.2.2 Output driver: > >>>> > >>>> "Internal pull-up, pull-down resistors, and pad keeper are disabled in > >>>> output mode." > > > > This would mean you'd have to rely on an external pull up for your use > > case. I wouldn't be surprised however if DSE=0 wouldn't count as "output > > mode". Given the reliability of NXP documentation I wouldn't bet neither > > on one nor the other possibility. > > Yeah, the NXP documentation sometimes does not really match reality. > My use case is based on the fact that I configure the pin as input in > the driver. Then it works just fine. > > >>> So I'd expect this to really work on i.MX6 but not the earlier SoCs > >>> without a gpio specifier. > >> > >> Maybe you would expect it to work but I already tested and measured > >> that weeks ago ;) It did not work. > > > > Which pin/gpio do we talk about? Which i.MX6 variant did you test this > > on? (Assuming i.MX6D or i.MX6Q and PAD_DISP0_DATA09, did you try setting > > > > IOMUXC_SW_MUX_CTL_PAD_DISP0_DATA09 (0x020E0194) = 0x00000005 > > IOMUXC_SW_PAD_CTL_PAD_DISP0_DATA09 (0x020E04A8) = 0x0000b080 > > > > and then play with GPIO 4.30 direction and output value?) > > My test setup is as follows: > - SoC is i.MX6DL or i.MX6S - I have three board variants in total. > - Pin used for PWM/GPIO is PAD_GPIO9. > - The pin is not connected to any circuit. Just a test point. > - pinctrl setup in DT: > - for "pwm": > - fsl,pins = <MX6QDL_PAD_GPIO_9__PWM1_OUT 0x8> > - IOMUXC_SW_MUX_CTL_PAD_GPIO09 = 0x00000004 > - IOMUXC_SW_PAD_CTL_PAD_GPIO09 = 0x00000008 > > - for "gpio": > - fsl,pins = <MX6QDL_PAD_GPIO_9__GPIO1_IO09 0xb000> > - IOMUXC_SW_MUX_CTL_PAD_GPIO09 = 0x00000005 > - IOMUXC_SW_PAD_CTL_PAD_GPIO09 = 0x0000b000 Does it help if you additionally set the ODE bit (bit 11) here? Thierry
Attachment:
signature.asc
Description: PGP signature
