On Thu, Nov 22, 2018 at 2:29 AM Biao Huang <biao.huang@xxxxxxxxxxxx> wrote:
>
> Add Ethernet support for MediaTek SoCs from the mt2712 family
>
> Signed-off-by: Biao Huang <biao.huang@xxxxxxxxxxxx>
> ---
> drivers/net/ethernet/stmicro/stmmac/Kconfig | 8 +
> drivers/net/ethernet/stmicro/stmmac/Makefile | 1 +
> .../net/ethernet/stmicro/stmmac/dwmac-mediatek.c | 364 ++++++++++++++++++++
> 3 files changed, 373 insertions(+)
> create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
>
> diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> index 324049e..6209cc1 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
> +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> @@ -75,6 +75,14 @@ config DWMAC_LPC18XX
> ---help---
> Support for NXP LPC18xx/43xx DWMAC Ethernet.
>
> +config DWMAC_MEDIATEK
> + tristate "MediaTek MT27xx GMAC support"
> + depends on OF && (ARCH_MEDIATEK || COMPILE_TEST)
> + help
> + Support for MediaTek GMAC Ethernet controller.
> +
> + This selects the MT2712 SoC support for the stmmac driver.
> +
> config DWMAC_MESON
> tristate "Amlogic Meson dwmac support"
> default ARCH_MESON
> diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
> index 99967a8..bf09701 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/Makefile
> +++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
> @@ -13,6 +13,7 @@ obj-$(CONFIG_STMMAC_PLATFORM) += stmmac-platform.o
> obj-$(CONFIG_DWMAC_ANARION) += dwmac-anarion.o
> obj-$(CONFIG_DWMAC_IPQ806X) += dwmac-ipq806x.o
> obj-$(CONFIG_DWMAC_LPC18XX) += dwmac-lpc18xx.o
> +obj-$(CONFIG_DWMAC_MEDIATEK) += dwmac-mediatek.o
> obj-$(CONFIG_DWMAC_MESON) += dwmac-meson.o dwmac-meson8b.o
> obj-$(CONFIG_DWMAC_OXNAS) += dwmac-oxnas.o
> obj-$(CONFIG_DWMAC_ROCKCHIP) += dwmac-rk.o
> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
> new file mode 100644
> index 0000000..dd8d4cc
> --- /dev/null
> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
> @@ -0,0 +1,364 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2018 MediaTek Inc.
> + */
> +#include <linux/io.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/of_net.h>
> +#include <linux/regmap.h>
> +#include <linux/stmmac.h>
> +
> +#include "stmmac.h"
> +#include "stmmac_platform.h"
> +
> +/* Peri Configuration register for mt2712 */
> +#define PERI_ETH_PHY_INTF_SEL 0x418
> +#define PHY_INTF_MII_GMII 0
> +#define PHY_INTF_RGMII 1
> +#define PHY_INTF_RMII 4
> +#define RMII_CLK_SRC_RXC BIT(4)
> +#define RMII_CLK_SRC_INTERNAL BIT(5)
> +
> +#define PERI_ETH_PHY_DLY 0x428
> +#define PHY_DLY_GTXC_INV BIT(6)
> +#define PHY_DLY_GTXC_ENABLE BIT(5)
> +#define PHY_DLY_GTXC_STAGES GENMASK(4, 0)
> +#define PHY_DLY_TXC_INV BIT(20)
> +#define PHY_DLY_TXC_ENABLE BIT(19)
> +#define PHY_DLY_TXC_STAGES GENMASK(18, 14)
> +#define PHY_DLY_TXC_SHIFT 14
> +#define PHY_DLY_RXC_INV BIT(13)
> +#define PHY_DLY_RXC_ENABLE BIT(12)
> +#define PHY_DLY_RXC_STAGES GENMASK(11, 7)
> +#define PHY_DLY_RXC_SHIFT 7
> +
> +#define PERI_ETH_DLY_FINE 0x800
> +#define ETH_RMII_DLY_TX_INV BIT(2)
> +#define ETH_FINE_DLY_GTXC BIT(1)
> +#define ETH_FINE_DLY_RXC BIT(0)
> +
> +struct mac_delay_struct {
> + u32 tx_delay;
> + u32 rx_delay;
> + u32 tx_inv;
bool should be enough
> + u32 rx_inv;
bool should be enough
> +};
> +
> +struct mediatek_dwmac_plat_data {
> + const struct mediatek_dwmac_variant *variant;
> + struct mac_delay_struct mac_delay;
> + struct clk_bulk_data *clks;
> + struct device_node *np;
> + struct regmap *peri_regmap;
> + struct device *dev;
> + int fine_tune;
bool
> + int phy_mode;
> + int rmii_rxc;
bool
> +};
> +
> +struct mediatek_dwmac_variant {
> + int (*dwmac_set_phy_interface)(struct mediatek_dwmac_plat_data *plat);
> + int (*dwmac_set_delay)(struct mediatek_dwmac_plat_data *plat);
> +
> + /* clock ids to be requested */
> + const char * const *clk_list;
> + int num_clks;
> +
> + u32 dma_bit_mask;
> + u32 rx_delay_max;
> + u32 tx_delay_max;
> +};
> +
> +/* list of clocks required for mac */
> +static const char * const mt2712_dwmac_clk_l[] = {
> + "axi", "apb", "mac_main", "ptp_ref"
> +};
> +
> +static int mt2712_set_interface(struct mediatek_dwmac_plat_data *plat)
> +{
> + int rmii_rxc = plat->rmii_rxc ? RMII_CLK_SRC_RXC : 0;
> + u32 intf_val = 0;
> +
> + /* select phy interface in top control domain */
> + switch (plat->phy_mode) {
> + case PHY_INTERFACE_MODE_MII:
> + intf_val |= PHY_INTF_MII_GMII;
> + break;
> + case PHY_INTERFACE_MODE_RMII:
> + intf_val |= PHY_INTF_RMII;
> + intf_val |= rmii_rxc;
how about putting into one line such as intf_val |= (PHY_INTF_RMII | rmii_rxc) ?
> + break;
> + case PHY_INTERFACE_MODE_RGMII:
> + case PHY_INTERFACE_MODE_RGMII_TXID:
> + case PHY_INTERFACE_MODE_RGMII_RXID:
> + case PHY_INTERFACE_MODE_RGMII_ID:
> + intf_val |= PHY_INTF_RGMII;
> + break;
> + default:
> + dev_err(plat->dev, "phy interface not supported\n");
> + return -EINVAL;
> + }
> +
> + regmap_write(plat->peri_regmap, PERI_ETH_PHY_INTF_SEL, intf_val);
> +
> + return 0;
> +}
> +
> +static int mt2712_set_delay(struct mediatek_dwmac_plat_data *plat)
> +{
> + struct mac_delay_struct *mac_delay = &plat->mac_delay;
> + u32 delay_val = 0;
> + u32 fine_val = 0;
The same type declaration can be put into the one line
> +
> + switch (plat->phy_mode) {
There exists some room for code optimization in the switch statement
such as PHY_INTERFACE_MODE_MII and PHY_INTERFACE_MODE_RGMII both are
almost the same and even the configuration for the other PHY modes can
reuse their partial setup. It appears to be better using a common way
to set up various PHY modes.
> + case PHY_INTERFACE_MODE_MII:
> + delay_val |= mac_delay->tx_delay ? PHY_DLY_TXC_ENABLE : 0;
> + delay_val |= (mac_delay->tx_delay << PHY_DLY_TXC_SHIFT) &
> + PHY_DLY_TXC_STAGES;
> + delay_val |= mac_delay->tx_inv ? PHY_DLY_TXC_INV : 0;
> + delay_val |= mac_delay->rx_delay ? PHY_DLY_RXC_ENABLE : 0;
> + delay_val |= (mac_delay->rx_delay << PHY_DLY_RXC_SHIFT) &
> + PHY_DLY_RXC_STAGES;
> + delay_val |= mac_delay->rx_inv ? PHY_DLY_RXC_INV : 0;
> + break;
> + case PHY_INTERFACE_MODE_RMII:
> + if (plat->rmii_rxc) {
> + delay_val |= mac_delay->rx_delay ?
> + PHY_DLY_RXC_ENABLE : 0;
> + delay_val |= (mac_delay->rx_delay <<
> + PHY_DLY_RXC_SHIFT) & PHY_DLY_RXC_STAGES;
> + delay_val |= mac_delay->rx_inv ? PHY_DLY_RXC_INV : 0;
> + fine_val |= mac_delay->tx_inv ?
> + ETH_RMII_DLY_TX_INV : 0;
why is fine_val got from tx_inv?
> + } else {
> + delay_val |= mac_delay->rx_delay ?
> + PHY_DLY_TXC_ENABLE : 0;
> + delay_val |= (mac_delay->rx_delay <<
> + PHY_DLY_TXC_SHIFT) & PHY_DLY_TXC_STAGES;
> + delay_val |= mac_delay->rx_inv ? PHY_DLY_TXC_INV : 0;
> + fine_val |= mac_delay->tx_inv ?
> + ETH_RMII_DLY_TX_INV : 0;
ditto, why is fine_val got from tx_inv?
> + }
> + break;
> + case PHY_INTERFACE_MODE_RGMII:
> + fine_val = plat->fine_tune ?
> + (ETH_FINE_DLY_GTXC | ETH_FINE_DLY_RXC) : 0;
> + delay_val |= mac_delay->tx_delay ? PHY_DLY_GTXC_ENABLE : 0;
> + delay_val |= mac_delay->tx_delay & PHY_DLY_GTXC_STAGES;
> + delay_val |= mac_delay->tx_inv ? PHY_DLY_GTXC_INV : 0;
> + delay_val |= mac_delay->rx_delay ? PHY_DLY_RXC_ENABLE : 0;
> + delay_val |= (mac_delay->rx_delay << PHY_DLY_RXC_SHIFT) &
> + PHY_DLY_RXC_STAGES;
> + delay_val |= mac_delay->rx_inv ? PHY_DLY_RXC_INV : 0;
> + break;
> + case PHY_INTERFACE_MODE_RGMII_TXID:
> + fine_val = plat->fine_tune ? ETH_FINE_DLY_RXC : 0;
> + delay_val |= mac_delay->rx_delay ? PHY_DLY_RXC_ENABLE : 0;
> + delay_val |= (mac_delay->rx_delay << PHY_DLY_RXC_SHIFT) &
> + PHY_DLY_RXC_STAGES;
> + delay_val |= mac_delay->rx_inv ? PHY_DLY_RXC_INV : 0;
why is PHY_INTERFACE_MODE_RGMII_TXID applied with *_RXC_* register
bits, not with *_TXC_* bits? I'm a little confused about what path the
register PHY_DLY_RXC_* cause the effects to? MAC to PHY or PHY to MAC?
> + break;
> + case PHY_INTERFACE_MODE_RGMII_RXID:
> + fine_val = plat->fine_tune ? ETH_FINE_DLY_GTXC : 0;
> + delay_val |= mac_delay->tx_delay ? PHY_DLY_GTXC_ENABLE : 0;
> + delay_val |= mac_delay->tx_delay & PHY_DLY_GTXC_STAGES;
> + delay_val |= mac_delay->tx_inv ? PHY_DLY_GTXC_INV : 0;
ditto, as the above quetion
> + break;
> + case PHY_INTERFACE_MODE_RGMII_ID:
> + break;
> + default:
> + dev_err(plat->dev, "phy interface not supported\n");
> + return -EINVAL;
> + }
> + regmap_write(plat->peri_regmap, PERI_ETH_PHY_DLY, delay_val);
> + regmap_write(plat->peri_regmap, PERI_ETH_DLY_FINE, fine_val);
> +
> + return 0;
> +}
> +
> +static const struct mediatek_dwmac_variant mt2712_gmac_variant = {
> + .dwmac_set_phy_interface = mt2712_set_interface,
> + .dwmac_set_delay = mt2712_set_delay,
> + .clk_list = mt2712_dwmac_clk_l,
> + .num_clks = ARRAY_SIZE(mt2712_dwmac_clk_l),
> + .dma_bit_mask = 33,
> + .rx_delay_max = 32,
> + .tx_delay_max = 32,
> +};
> +
> +static int mediatek_dwmac_config_dt(struct mediatek_dwmac_plat_data *plat)
> +{
> + u32 tx_delay, rx_delay;
> +
> + plat->peri_regmap = syscon_regmap_lookup_by_phandle(plat->np, "mediatek,pericfg");
> + if (IS_ERR(plat->peri_regmap)) {
> + dev_err(plat->dev, "Failed to get pericfg syscon\n");
> + return PTR_ERR(plat->peri_regmap);
> + }
> +
> + plat->phy_mode = of_get_phy_mode(plat->np);
> + if (plat->phy_mode < 0) {
> + dev_err(plat->dev, "not find phy-mode\n");
> + return -EINVAL;
> + }
> +
> + if (!of_property_read_u32(plat->np, "mediatek,tx-delay", &tx_delay)) {
> + if (tx_delay < plat->variant->tx_delay_max) {
> + plat->mac_delay.tx_delay = tx_delay;
> + } else {
> + dev_err(plat->dev, "Invalid TX clock delay: %d\n", tx_delay);
> + return -EINVAL;
> + }
> + }
> +
> + if (!of_property_read_u32(plat->np, "mediatek,rx-delay", &rx_delay)) {
> + if (rx_delay < plat->variant->rx_delay_max) {
> + plat->mac_delay.rx_delay = rx_delay;
> + } else {
> + dev_err(plat->dev, "Invalid RX clock delay: %d\n", rx_delay);
> + return -EINVAL;
> + }
> + }
> +
> + plat->mac_delay.tx_inv = of_property_read_bool(plat->np, "mediatek,txc-inverse");
> + plat->mac_delay.rx_inv = of_property_read_bool(plat->np, "mediatek,rxc-inverse");
> + plat->fine_tune = of_property_read_bool(plat->np, "mediatek,fine-tune");
> + plat->rmii_rxc = of_property_read_bool(plat->np, "mediatek,rmii-rxc");
> +
> + return 0;
> +}
> +
> +static int mediatek_dwmac_clk_init(struct mediatek_dwmac_plat_data *plat)
> +{
> + const struct mediatek_dwmac_variant *variant = plat->variant;
> + int num = variant->num_clks;
> + int i;
put into the same line seems good
> +
> + plat->clks = devm_kcalloc(plat->dev, num, sizeof(*plat->clks), GFP_KERNEL);
> + if (!plat->clks)
> + return -ENOMEM;
> +
> + for (i = 0; i < num; i++)
> + plat->clks[i].id = variant->clk_list[i];
> +
> + return devm_clk_bulk_get(plat->dev, num, plat->clks);
> +}
> +
> +static int mediatek_dwmac_init(struct platform_device *pdev, void *priv)
> +{
> + struct mediatek_dwmac_plat_data *plat = priv;
> + const struct mediatek_dwmac_variant *variant = plat->variant;
> + int ret = 0;
zero initialized seems unnecessary
> +
> + ret = dma_set_mask_and_coherent(plat->dev, DMA_BIT_MASK(variant->dma_bit_mask));
> + if (ret) {
> + dev_err(plat->dev, "No suitable DMA available, err = %d\n", ret);
> + return ret;
> + }
> +
> + ret = variant->dwmac_set_phy_interface(plat);
> + if (ret) {
> + dev_err(plat->dev, "failed to set phy interface, err = %d\n", ret);
> + return ret;
> + }
> +
> + ret = variant->dwmac_set_delay(plat);
> + if (ret) {
> + dev_err(plat->dev, "failed to set delay value, err = %d\n", ret);
> + return ret;
> + }
> +
> + ret = clk_bulk_prepare_enable(variant->num_clks, plat->clks);
> + if (ret) {
> + dev_err(plat->dev, "failed to enable clks, err = %d\n", ret);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static void mediatek_dwmac_exit(struct platform_device *pdev, void *priv)
> +{
> + struct mediatek_dwmac_plat_data *plat = priv;
> + const struct mediatek_dwmac_variant *variant = plat->variant;
> +
> + clk_bulk_disable_unprepare(variant->num_clks, plat->clks);
> +}
> +
> +static int mediatek_dwmac_probe(struct platform_device *pdev)
> +{
> + struct mediatek_dwmac_plat_data *priv_plat;
> + struct plat_stmmacenet_data *plat_dat;
> + struct stmmac_resources stmmac_res;
> + int ret = 0;
zero initialized seems unnecessary
> +
> + priv_plat = devm_kzalloc(&pdev->dev, sizeof(*priv_plat), GFP_KERNEL);
> + if (!priv_plat)
> + return -ENOMEM;
> +
> + priv_plat->variant = of_device_get_match_data(&pdev->dev);
> + if (!priv_plat->variant) {
> + dev_err(&pdev->dev, "Missing dwmac-mediatek variant\n");
> + return -EINVAL;
> + }
> +
> + priv_plat->dev = &pdev->dev;
> + priv_plat->np = pdev->dev.of_node;
> +
> + ret = mediatek_dwmac_config_dt(priv_plat);
> + if (ret)
> + return ret;
> +
> + ret = mediatek_dwmac_clk_init(priv_plat);
> + if (ret)
> + return ret;
> +
> + ret = stmmac_get_platform_resources(pdev, &stmmac_res);
> + if (ret)
> + return ret;
> +
> + plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac);
> + if (IS_ERR(plat_dat))
> + return PTR_ERR(plat_dat);
> +
> + plat_dat->interface = priv_plat->phy_mode;
> + /* clk_csr_i = 250-300MHz & MDC = clk_csr_i/124 */
> + plat_dat->clk_csr = 5;
> + plat_dat->has_gmac4 = 1;
> + plat_dat->has_gmac = 0;
> + plat_dat->pmt = 0;
> + plat_dat->maxmtu = ETH_DATA_LEN;
> + plat_dat->bsp_priv = priv_plat;
> + plat_dat->init = mediatek_dwmac_init;
> + plat_dat->exit = mediatek_dwmac_exit;
> + mediatek_dwmac_init(pdev, priv_plat);
> +
> + ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
> + if (ret) {
> + stmmac_remove_config_dt(pdev, plat_dat);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static const struct of_device_id mediatek_dwmac_match[] = {
> + { .compatible = "mediatek,mt2712-gmac",
> + .data = &mt2712_gmac_variant },
> + { }
> +};
> +
> +MODULE_DEVICE_TABLE(of, mediatek_dwmac_match);
> +
> +static struct platform_driver mediatek_dwmac_driver = {
> + .probe = mediatek_dwmac_probe,
> + .remove = stmmac_pltfr_remove,
> + .driver = {
> + .name = "dwmac-mediatek",
> + .pm = &stmmac_pltfr_pm_ops,
> + .of_match_table = mediatek_dwmac_match,
> + },
> +};
> +module_platform_driver(mediatek_dwmac_driver);
> --
> 1.7.9.5
>
>
> _______________________________________________
> Linux-mediatek mailing list
> Linux-mediatek@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-mediatek
