Dne četrtek, 01. november 2018 ob 08:38:33 CET je Lothar Felten napisal(a):
> This patch adds a node for the mali 400 GPU of the R40/V40 SoC
>
> Signed-off-by: Lothar Felten <lothar.felten@xxxxxxxxx>
> ---
> arch/arm/boot/dts/sun8i-r40.dtsi | 28 +++++++++++++++++++++++++++-
> 1 file changed, 27 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi
> b/arch/arm/boot/dts/sun8i-r40.dtsi index 6f4c9ca5a3ee..ddf765e931f3 100644
> --- a/arch/arm/boot/dts/sun8i-r40.dtsi
> +++ b/arch/arm/boot/dts/sun8i-r40.dtsi
> @@ -542,6 +542,31 @@
>
> };
>
> + mali: gpu@1c40000 {
> + compatible = "allwinner,sun7i-a20-mali", "arm,mali-400";
> + reg = <0x01c40000 0x10000>;
> + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "gp",
> + "gpmmu",
> + "pp0",
> + "ppmmu0",
> + "pp1",
> + "ppmmu1",
> + "pmu";
> + clocks = <&ccu CLK_BUS_GPU>, <&ccu CLK_GPU>;
> + clock-names = "bus", "core";
> + resets = <&ccu RST_BUS_GPU>;
> +
> + assigned-clocks = <&ccu CLK_GPU>;
> + assigned-clock-rates = <384000000>;
In previous e-mail I already stated that above 2 lines doesn't belong here.
Driver is responsible for clock rate management.
> + };
> +
> gmac: ethernet@1c50000 {
> compatible = "allwinner,sun8i-r40-gmac";
> syscon = <&ccu>;
> @@ -813,7 +838,8 @@
> };
>
> hdmi_phy: hdmi-phy@1ef0000 {
> - compatible = "allwinner,sun8i-r40-hdmi-phy";
> + compatible = "allwinner,sun8i-r40-hdmi-phy",
> + "allwinner,sun50i-a64-hdmi-phy";
In previous e-mail I also stated that above changes are not related to GPU
node and they are also not needed, since HDMI on R40 works without this.
> reg = <0x01ef0000 0x10000>;
> clocks = <&ccu CLK_BUS_HDMI1>, <&ccu CLK_HDMI_SLOW>,
> <&ccu 7>, <&ccu 16>;
You cleary didn't read rules for patch submission. When you are sending new
version of the patch, you have to state which version is it in subject line
and write a changelog below "---" line.
Best regards,
Jernej
