> -----Original Message-----
> From: Li Yang <leoyang.li@xxxxxxx>
> Sent: Friday, October 26, 2018 1:19 AM
> To: Vabhav Sharma <vabhav.sharma@xxxxxxx>
> Cc: Sudeep Holla <sudeep.holla@xxxxxxx>; Scott Wood
> <oss@xxxxxxxxxxxx>; lkml <linux-kernel@xxxxxxxxxxxxxxx>; open list:OPEN
> FIRMWARE AND FLATTENED DEVICE TREE BINDINGS
> <devicetree@xxxxxxxxxxxxxxx>; Rob Herring <robh+dt@xxxxxxxxxx>; Mark
> Rutland <mark.rutland@xxxxxxx>; linuxppc-dev <linuxppc-
> dev@xxxxxxxxxxxxxxxx>; moderated list:ARM/FREESCALE IMX / MXC ARM
> ARCHITECTURE <linux-arm-kernel@xxxxxxxxxxxxxxxxxxx>; Michael Turquette
> <mturquette@xxxxxxxxxxxx>; sboyd@xxxxxxxxxx; Rafael J. Wysocki
> <rjw@xxxxxxxxxxxxx>; Viresh Kumar <viresh.kumar@xxxxxxxxxx>; linux-clk
> <linux-clk@xxxxxxxxxxxxxxx>; linux-pm@xxxxxxxxxxxxxxx; linux-kernel-
> owner@xxxxxxxxxxxxxxx; Catalin Marinas <catalin.marinas@xxxxxxx>; Will
> Deacon <will.deacon@xxxxxxx>; Greg Kroah-Hartman
> <gregkh@xxxxxxxxxxxxxxxxxxx>; Arnd Bergmann <arnd@xxxxxxxx>; Kate
> Stewart <kstewart@xxxxxxxxxxxxxxxxxxx>; yamada.masahiro@xxxxxxxxxxxxx;
> Shawn Guo <shawnguo@xxxxxxxxxx>; Russell King <linux@xxxxxxxxxxxxxxx>;
> Adrian Hunter <adrian.hunter@xxxxxxxxx>; Ulf Hansson
> <ulf.hansson@xxxxxxxxxx>; Varun Sethi <V.Sethi@xxxxxxx>; Udit Kumar
> <udit.kumar@xxxxxxx>; Pankaj Bansal <pankaj.bansal@xxxxxxx>; Ramneek
> Mehresh <ramneek.mehresh@xxxxxxx>; Ying Zhang
> <ying.zhang22455@xxxxxxx>; Nipun Gupta <nipun.gupta@xxxxxxx>;
> Priyanka Jain <priyanka.jain@xxxxxxx>; Yogesh Narayan Gaur
> <yogeshnarayan.gaur@xxxxxxx>; Sriram Dash <sriram.dash@xxxxxxx>;
> Horia Geanta <horia.geanta@xxxxxxx>; Ran Wang <ran.wang_1@xxxxxxx>;
> Yinbo Zhu <yinbo.zhu@xxxxxxx>
> Subject: Re: [PATCH v6 5/6] arm64: dts: add QorIQ LX2160A SoC support
>
> On Thu, Oct 25, 2018 at 2:03 AM Vabhav Sharma <vabhav.sharma@xxxxxxx>
> wrote:
> >
> > LX2160A SoC is based on Layerscape Chassis Generation 3.2 Architecture.
> >
> > LX2160A features an advanced 16 64-bit ARM v8 CortexA72 processor
> > cores in 8 cluster, CCN508, GICv3,two 64-bit DDR4 memory controller, 8
> > I2C controllers, 3 dspi, 2 esdhc,2 USB 3.0, mmu 500, 3 SATA, 4 PL011
> > SBSA UARTs etc.
> >
> > Signed-off-by: Ramneek Mehresh <ramneek.mehresh@xxxxxxx>
> > Signed-off-by: Zhang Ying-22455 <ying.zhang22455@xxxxxxx>
> > Signed-off-by: Nipun Gupta <nipun.gupta@xxxxxxx>
> > Signed-off-by: Priyanka Jain <priyanka.jain@xxxxxxx>
> > Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@xxxxxxx>
> > Signed-off-by: Sriram Dash <sriram.dash@xxxxxxx>
> > Signed-off-by: Vabhav Sharma <vabhav.sharma@xxxxxxx>
> > Signed-off-by: Horia Geanta <horia.geanta@xxxxxxx>
> > Signed-off-by: Ran Wang <ran.wang_1@xxxxxxx>
> > Signed-off-by: Yinbo Zhu <yinbo.zhu@xxxxxxx>
> > ---
> > arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 766
> > +++++++++++++++++++++++++
> > 1 file changed, 766 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
> > b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
> > new file mode 100644
> > index 0000000..9fcfd48
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
> > @@ -0,0 +1,766 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT) // // Device Tree
> > +Include file for Layerscape-LX2160A family SoC.
> > +//
> > +// Copyright 2018 NXP
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +
> > +/memreserve/ 0x80000000 0x00010000;
> > +
> > +/ {
> > + compatible = "fsl,lx2160a";
> > + interrupt-parent = <&gic>;
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > +
> > + cpus {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + // 8 clusters having 2 Cortex-A72 cores each
> > + cpu@0 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a72";
> > + enable-method = "psci";
> > + reg = <0x0>;
> > + clocks = <&clockgen 1 0>;
> > + d-cache-size = <0x8000>;
> > + d-cache-line-size = <64>;
> > + d-cache-sets = <128>;
> > + i-cache-size = <0xC000>;
> > + i-cache-line-size = <64>;
> > + i-cache-sets = <192>;
> > + next-level-cache = <&cluster0_l2>;
> > + };
> > +
> > + cpu@1 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a72";
> > + enable-method = "psci";
> > + reg = <0x1>;
> > + clocks = <&clockgen 1 0>;
> > + d-cache-size = <0x8000>;
> > + d-cache-line-size = <64>;
> > + d-cache-sets = <128>;
> > + i-cache-size = <0xC000>;
> > + i-cache-line-size = <64>;
> > + i-cache-sets = <192>;
> > + next-level-cache = <&cluster0_l2>;
> > + };
> > +
> > + cpu@100 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a72";
> > + enable-method = "psci";
> > + reg = <0x100>;
> > + clocks = <&clockgen 1 1>;
> > + d-cache-size = <0x8000>;
> > + d-cache-line-size = <64>;
> > + d-cache-sets = <128>;
> > + i-cache-size = <0xC000>;
> > + i-cache-line-size = <64>;
> > + i-cache-sets = <192>;
> > + next-level-cache = <&cluster1_l2>;
> > + };
> > +
> > + cpu@101 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a72";
> > + enable-method = "psci";
> > + reg = <0x101>;
> > + clocks = <&clockgen 1 1>;
> > + d-cache-size = <0x8000>;
> > + d-cache-line-size = <64>;
> > + d-cache-sets = <128>;
> > + i-cache-size = <0xC000>;
> > + i-cache-line-size = <64>;
> > + i-cache-sets = <192>;
> > + next-level-cache = <&cluster1_l2>;
> > + };
> > +
> > + cpu@200 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a72";
> > + enable-method = "psci";
> > + reg = <0x200>;
> > + clocks = <&clockgen 1 2>;
> > + d-cache-size = <0x8000>;
> > + d-cache-line-size = <64>;
> > + d-cache-sets = <128>;
> > + i-cache-size = <0xC000>;
> > + i-cache-line-size = <64>;
> > + i-cache-sets = <192>;
> > + next-level-cache = <&cluster2_l2>;
> > + };
> > +
> > + cpu@201 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a72";
> > + enable-method = "psci";
> > + reg = <0x201>;
> > + clocks = <&clockgen 1 2>;
> > + d-cache-size = <0x8000>;
> > + d-cache-line-size = <64>;
> > + d-cache-sets = <128>;
> > + i-cache-size = <0xC000>;
> > + i-cache-line-size = <64>;
> > + i-cache-sets = <192>;
> > + next-level-cache = <&cluster2_l2>;
> > + };
> > +
> > + cpu@300 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a72";
> > + enable-method = "psci";
> > + reg = <0x300>;
> > + clocks = <&clockgen 1 3>;
> > + d-cache-size = <0x8000>;
> > + d-cache-line-size = <64>;
> > + d-cache-sets = <128>;
> > + i-cache-size = <0xC000>;
> > + i-cache-line-size = <64>;
> > + i-cache-sets = <192>;
> > + next-level-cache = <&cluster3_l2>;
> > + };
> > +
> > + cpu@301 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a72";
> > + enable-method = "psci";
> > + reg = <0x301>;
> > + clocks = <&clockgen 1 3>;
> > + d-cache-size = <0x8000>;
> > + d-cache-line-size = <64>;
> > + d-cache-sets = <128>;
> > + i-cache-size = <0xC000>;
> > + i-cache-line-size = <64>;
> > + i-cache-sets = <192>;
> > + next-level-cache = <&cluster3_l2>;
> > + };
> > +
> > + cpu@400 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a72";
> > + enable-method = "psci";
> > + reg = <0x400>;
> > + clocks = <&clockgen 1 4>;
> > + d-cache-size = <0x8000>;
> > + d-cache-line-size = <64>;
> > + d-cache-sets = <128>;
> > + i-cache-size = <0xC000>;
> > + i-cache-line-size = <64>;
> > + i-cache-sets = <192>;
> > + next-level-cache = <&cluster4_l2>;
> > + };
> > +
> > + cpu@401 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a72";
> > + enable-method = "psci";
> > + reg = <0x401>;
> > + clocks = <&clockgen 1 4>;
> > + d-cache-size = <0x8000>;
> > + d-cache-line-size = <64>;
> > + d-cache-sets = <128>;
> > + i-cache-size = <0xC000>;
> > + i-cache-line-size = <64>;
> > + i-cache-sets = <192>;
> > + next-level-cache = <&cluster4_l2>;
> > + };
> > +
> > + cpu@500 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a72";
> > + enable-method = "psci";
> > + reg = <0x500>;
> > + clocks = <&clockgen 1 5>;
> > + d-cache-size = <0x8000>;
> > + d-cache-line-size = <64>;
> > + d-cache-sets = <128>;
> > + i-cache-size = <0xC000>;
> > + i-cache-line-size = <64>;
> > + i-cache-sets = <192>;
> > + next-level-cache = <&cluster5_l2>;
> > + };
> > +
> > + cpu@501 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a72";
> > + enable-method = "psci";
> > + reg = <0x501>;
> > + clocks = <&clockgen 1 5>;
> > + d-cache-size = <0x8000>;
> > + d-cache-line-size = <64>;
> > + d-cache-sets = <128>;
> > + i-cache-size = <0xC000>;
> > + i-cache-line-size = <64>;
> > + i-cache-sets = <192>;
> > + next-level-cache = <&cluster5_l2>;
> > + };
> > +
> > + cpu@600 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a72";
> > + enable-method = "psci";
> > + reg = <0x600>;
> > + clocks = <&clockgen 1 6>;
> > + d-cache-size = <0x8000>;
> > + d-cache-line-size = <64>;
> > + d-cache-sets = <128>;
> > + i-cache-size = <0xC000>;
> > + i-cache-line-size = <64>;
> > + i-cache-sets = <192>;
> > + next-level-cache = <&cluster6_l2>;
> > + };
> > +
> > + cpu@601 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a72";
> > + enable-method = "psci";
> > + reg = <0x601>;
> > + clocks = <&clockgen 1 6>;
> > + d-cache-size = <0x8000>;
> > + d-cache-line-size = <64>;
> > + d-cache-sets = <128>;
> > + i-cache-size = <0xC000>;
> > + i-cache-line-size = <64>;
> > + i-cache-sets = <192>;
> > + next-level-cache = <&cluster6_l2>;
> > + };
> > +
> > + cpu@700 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a72";
> > + enable-method = "psci";
> > + reg = <0x700>;
> > + clocks = <&clockgen 1 7>;
> > + d-cache-size = <0x8000>;
> > + d-cache-line-size = <64>;
> > + d-cache-sets = <128>;
> > + i-cache-size = <0xC000>;
> > + i-cache-line-size = <64>;
> > + i-cache-sets = <192>;
> > + next-level-cache = <&cluster7_l2>;
> > + };
> > +
> > + cpu@701 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a72";
> > + enable-method = "psci";
> > + reg = <0x701>;
> > + clocks = <&clockgen 1 7>;
> > + d-cache-size = <0x8000>;
> > + d-cache-line-size = <64>;
> > + d-cache-sets = <128>;
> > + i-cache-size = <0xC000>;
> > + i-cache-line-size = <64>;
> > + i-cache-sets = <192>;
> > + next-level-cache = <&cluster7_l2>;
> > + };
> > +
> > + cluster0_l2: l2-cache0 {
> > + compatible = "cache";
> > + cache-size = <0x100000>;
> > + cache-line-size = <64>;
> > + cache-sets = <1024>;
> > + cache-level = <2>;
> > + };
> > +
> > + cluster1_l2: l2-cache1 {
> > + compatible = "cache";
> > + cache-size = <0x100000>;
> > + cache-line-size = <64>;
> > + cache-sets = <1024>;
> > + cache-level = <2>;
> > + };
> > +
> > + cluster2_l2: l2-cache2 {
> > + compatible = "cache";
> > + cache-size = <0x100000>;
> > + cache-line-size = <64>;
> > + cache-sets = <1024>;
> > + cache-level = <2>;
> > + };
> > +
> > + cluster3_l2: l2-cache3 {
> > + compatible = "cache";
> > + cache-size = <0x100000>;
> > + cache-line-size = <64>;
> > + cache-sets = <1024>;
> > + cache-level = <2>;
> > + };
> > +
> > + cluster4_l2: l2-cache4 {
> > + compatible = "cache";
> > + cache-size = <0x100000>;
> > + cache-line-size = <64>;
> > + cache-sets = <1024>;
> > + cache-level = <2>;
> > + };
> > +
> > + cluster5_l2: l2-cache5 {
> > + compatible = "cache";
> > + cache-size = <0x100000>;
> > + cache-line-size = <64>;
> > + cache-sets = <1024>;
> > + cache-level = <2>;
> > + };
> > +
> > + cluster6_l2: l2-cache6 {
> > + compatible = "cache";
> > + cache-size = <0x100000>;
> > + cache-line-size = <64>;
> > + cache-sets = <1024>;
> > + cache-level = <2>;
> > + };
> > +
> > + cluster7_l2: l2-cache7 {
> > + compatible = "cache";
> > + cache-size = <0x100000>;
> > + cache-line-size = <64>;
> > + cache-sets = <1024>;
> > + cache-level = <2>;
> > + };
> > + };
> > +
> > + gic: interrupt-controller@6000000 {
> > + compatible = "arm,gic-v3";
> > + reg = <0x0 0x06000000 0 0x10000>, // GIC Dist
> > + <0x0 0x06200000 0 0x200000>, // GICR (RD_base +
> > + // SGI_base)
> > + <0x0 0x0c0c0000 0 0x2000>, // GICC
> > + <0x0 0x0c0d0000 0 0x1000>, // GICH
> > + <0x0 0x0c0e0000 0 0x20000>; // GICV
> > + #interrupt-cells = <3>;
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > + interrupt-controller;
> > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
> > +
> > + its: gic-its@6020000 {
> > + compatible = "arm,gic-v3-its";
> > + msi-controller;
> > + reg = <0x0 0x6020000 0 0x20000>;
> > + };
> > + };
> > +
> > + timer {
> > + compatible = "arm,armv8-timer";
> > + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > +
> > + pmu {
> > + compatible = "arm,cortex-a72-pmu";
> > + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW>;
> > + };
> > +
> > + psci {
> > + compatible = "arm,psci-0.2";
> > + method = "smc";
> > + };
> > +
> > + memory@80000000 {
> > + // DRAM space - 1, size : 2 GB DRAM
> > + device_type = "memory";
> > + reg = <0x00000000 0x80000000 0 0x80000000>;
> > + };
> > +
> > + ddr1: memory-controller@1080000 {
> > + compatible = "fsl,qoriq-memory-controller";
> > + reg = <0x0 0x1080000 0x0 0x1000>;
> > + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> > + little-endian;
> > + };
> > +
> > + ddr2: memory-controller@1090000 {
> > + compatible = "fsl,qoriq-memory-controller";
> > + reg = <0x0 0x1090000 0x0 0x1000>;
> > + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
> > + little-endian;
> > + };
> > +
> > + // One clock unit-sysclk node which bootloader require during DT fix-
> up
> > + sysclk: sysclk {
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <100000000>;
>
> Would be even better if you can add a comment "fixed up by bootloader"
> to the property too.
Ok
>
> > + clock-output-names = "sysclk";
> > + };
> > +
> > + soc {
> > + compatible = "simple-bus";
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + crypto: crypto@8000000 {
> > + compatible = "fsl,sec-v5.0", "fsl,sec-v4.0";
> > + fsl,sec-era = <10>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges = <0x0 0x00 0x8000000 0x100000>;
> > + reg = <0x00 0x8000000 0x0 0x100000>;
> > + interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
> > + dma-coherent;
> > + status = "disabled";
> > +
> > + sec_jr0: jr@10000 {
> > + compatible = "fsl,sec-v5.0-job-ring",
> > + "fsl,sec-v4.0-job-ring";
> > + reg = <0x10000 0x10000>;
> > + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > +
> > + sec_jr1: jr@20000 {
> > + compatible = "fsl,sec-v5.0-job-ring",
> > + "fsl,sec-v4.0-job-ring";
> > + reg = <0x20000 0x10000>;
> > + interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > +
> > + sec_jr2: jr@30000 {
> > + compatible = "fsl,sec-v5.0-job-ring",
> > + "fsl,sec-v4.0-job-ring";
> > + reg = <0x30000 0x10000>;
> > + interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > +
> > + sec_jr3: jr@40000 {
> > + compatible = "fsl,sec-v5.0-job-ring",
> > + "fsl,sec-v4.0-job-ring";
> > + reg = <0x40000 0x10000>;
> > + interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > + };
> > +
> > + clockgen: clock-controller@1300000 {
> > + compatible = "fsl,lx2160a-clockgen";
> > + reg = <0 0x1300000 0 0xa0000>;
> > + #clock-cells = <2>;
> > + clocks = <&sysclk>;
> > + };
> > +
> > + dcfg: syscon@1e00000 {
> > + compatible = "fsl,lx2160a-dcfg", "syscon";
> > + reg = <0x0 0x1e00000 0x0 0x10000>;
> > + little-endian;
> > + };
> > +
> > + i2c0: i2c@2000000 {
> > + compatible = "fsl,vf610-i2c";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0x0 0x2000000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
> > + clock-names = "i2c";
> > + clocks = <&clockgen 4 7>;
> > + scl-gpio = <&gpio2 15 GPIO_ACTIVE_HIGH>;
> > + status = "disabled";
> > + };
> > +
> > + i2c1: i2c@2010000 {
> > + compatible = "fsl,vf610-i2c";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0x0 0x2010000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
> > + clock-names = "i2c";
> > + clocks = <&clockgen 4 7>;
> > + status = "disabled";
> > + };
> > +
> > + i2c2: i2c@2020000 {
> > + compatible = "fsl,vf610-i2c";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0x0 0x2020000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
> > + clock-names = "i2c";
> > + clocks = <&clockgen 4 7>;
> > + status = "disabled";
> > + };
> > +
> > + i2c3: i2c@2030000 {
> > + compatible = "fsl,vf610-i2c";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0x0 0x2030000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
> > + clock-names = "i2c";
> > + clocks = <&clockgen 4 7>;
> > + status = "disabled";
> > + };
> > +
> > + i2c4: i2c@2040000 {
> > + compatible = "fsl,vf610-i2c";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0x0 0x2040000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
> > + clock-names = "i2c";
> > + clocks = <&clockgen 4 7>;
> > + scl-gpio = <&gpio2 16 GPIO_ACTIVE_HIGH>;
> > + status = "disabled";
> > + };
> > +
> > + i2c5: i2c@2050000 {
> > + compatible = "fsl,vf610-i2c";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0x0 0x2050000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
> > + clock-names = "i2c";
> > + clocks = <&clockgen 4 7>;
> > + status = "disabled";
> > + };
> > +
> > + i2c6: i2c@2060000 {
> > + compatible = "fsl,vf610-i2c";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0x0 0x2060000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
> > + clock-names = "i2c";
> > + clocks = <&clockgen 4 7>;
> > + status = "disabled";
> > + };
> > +
> > + i2c7: i2c@2070000 {
> > + compatible = "fsl,vf610-i2c";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0x0 0x2070000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
> > + clock-names = "i2c";
> > + clocks = <&clockgen 4 7>;
> > + status = "disabled";
> > + };
> > +
> > + esdhc0: esdhc@2140000 {
> > + compatible = "fsl,esdhc";
> > + reg = <0x0 0x2140000 0x0 0x10000>;
> > + interrupts = <0 28 0x4>; /* Level high type */
> > + clocks = <&clockgen 4 1>;
> > + voltage-ranges = <1800 1800 3300 3300>;
> > + sdhci,auto-cmd12;
> > + little-endian;
> > + bus-width = <4>;
> > + status = "disabled";
> > + };
> > +
> > + esdhc1: esdhc@2150000 {
> > + compatible = "fsl,esdhc";
> > + reg = <0x0 0x2150000 0x0 0x10000>;
> > + interrupts = <0 63 0x4>; /* Level high type */
> > + clocks = <&clockgen 4 1>;
> > + voltage-ranges = <1800 1800 3300 3300>;
> > + sdhci,auto-cmd12;
> > + broken-cd;
> > + little-endian;
> > + bus-width = <4>;
> > + status = "disabled";
> > + };
> > +
> > + uart0: serial@21c0000 {
> > + compatible = "arm,sbsa-uart","arm,pl011";
> > + reg = <0x0 0x21c0000 0x0 0x1000>;
> > + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
> > + current-speed = <115200>;
> > + status = "disabled";
> > + };
> > +
> > + uart1: serial@21d0000 {
> > + compatible = "arm,sbsa-uart","arm,pl011";
> > + reg = <0x0 0x21d0000 0x0 0x1000>;
> > + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
> > + current-speed = <115200>;
> > + status = "disabled";
> > + };
> > +
> > + uart2: serial@21e0000 {
> > + compatible = "arm,sbsa-uart","arm,pl011";
> > + reg = <0x0 0x21e0000 0x0 0x1000>;
> > + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
> > + current-speed = <115200>;
> > + status = "disabled";
> > + };
> > +
> > + uart3: serial@21f0000 {
> > + compatible = "arm,sbsa-uart","arm,pl011";
> > + reg = <0x0 0x21f0000 0x0 0x1000>;
> > + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
> > + current-speed = <115200>;
> > + status = "disabled";
> > + };
> > +
> > + gpio0: gpio@2300000 {
> > + compatible = "fsl,qoriq-gpio";
> > + reg = <0x0 0x2300000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
> > + gpio-controller;
> > + little-endian;
> > + #gpio-cells = <2>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + };
> > +
> > + gpio1: gpio@2310000 {
> > + compatible = "fsl,qoriq-gpio";
> > + reg = <0x0 0x2310000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
> > + gpio-controller;
> > + little-endian;
> > + #gpio-cells = <2>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + };
> > +
> > + gpio2: gpio@2320000 {
> > + compatible = "fsl,qoriq-gpio";
> > + reg = <0x0 0x2320000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> > + gpio-controller;
> > + little-endian;
> > + #gpio-cells = <2>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + };
> > +
> > + gpio3: gpio@2330000 {
> > + compatible = "fsl,qoriq-gpio";
> > + reg = <0x0 0x2330000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> > + gpio-controller;
> > + little-endian;
> > + #gpio-cells = <2>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + };
> > +
> > + watchdog@23a0000 {
> > + compatible = "arm,sbsa-gwdt";
> > + reg = <0x0 0x23a0000 0 0x1000>,
> > + <0x0 0x2390000 0 0x1000>;
> > + interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
> > + timeout-sec = <30>;
> > + };
> > +
> > + usb0: usb@3100000 {
> > + compatible = "snps,dwc3";
> > + reg = <0x0 0x3100000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
> > + dr_mode = "host";
> > + snps,quirk-frame-length-adjustment = <0x20>;
> > + snps,dis_rxdet_inp3_quirk;
> > + status = "disabled";
> > + };
> > +
> > + usb1: usb@3110000 {
> > + compatible = "snps,dwc3";
> > + reg = <0x0 0x3110000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
> > + dr_mode = "host";
> > + snps,quirk-frame-length-adjustment = <0x20>;
> > + snps,dis_rxdet_inp3_quirk;
> > + status = "disabled";
> > + };
> > +
> > + smmu: iommu@5000000 {
> > + compatible = "arm,mmu-500";
> > + reg = <0 0x5000000 0 0x800000>;
> > + #iommu-cells = <1>;
> > + #global-interrupts = <14>;
> > + // global secure fault
> > + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
> > + // combined secure
> > + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
> > + // global non-secure fault
> > + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
> > + // combined non-secure
> > + <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
> > + // performance counter interrupts 0-9
> > + <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>,
> > + // per context interrupt, 64 interrupts
> > + <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
> > + dma-coherent;
> > + };
> > + };
> > +};
> > --
> > 2.7.4
> >
