Add device-tree binding that describes CPU frequency-scaling hardware
found on NVIDIA Tegra20/30 SoC's.
Signed-off-by: Dmitry Osipenko <digetx@xxxxxxxxx>
---
.../cpufreq/nvidia,tegra20-cpufreq.txt | 96 +++++++++++++++++++
1 file changed, 96 insertions(+)
create mode 100644 Documentation/devicetree/bindings/cpufreq/nvidia,tegra20-cpufreq.txt
diff --git a/Documentation/devicetree/bindings/cpufreq/nvidia,tegra20-cpufreq.txt b/Documentation/devicetree/bindings/cpufreq/nvidia,tegra20-cpufreq.txt
new file mode 100644
index 000000000000..a8023ea7a99f
--- /dev/null
+++ b/Documentation/devicetree/bindings/cpufreq/nvidia,tegra20-cpufreq.txt
@@ -0,0 +1,96 @@
+Binding for NVIDIA Tegra20 CPUFreq
+==================================
+
+Required properties:
+- clocks: Must contain an entry for each entry in clock-names.
+ See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+ - pll_x: main-parent for CPU clock, must be the first entry
+ - intermediate: intermediate-parent for CPU clock
+ - cclk: the CPU clock
+- operating-points-v2: See ../bindings/opp/opp.txt for details.
+- #cooling-cells: Should be 2. See ../thermal/thermal.txt for details.
+
+For each opp entry in 'operating-points-v2' table:
+- opp-supported-hw: Two bitfields indicating:
+ On Tegra20:
+ 1. CPU process ID mask
+ 2. SoC speedo ID mask
+
+ On Tegra30:
+ 1. CPU process ID mask
+ 2. CPU speedo ID mask
+
+ A bitwise AND is performed against these values and if any bit
+ matches, the OPP gets enabled.
+
+- opp-microvolt: CPU voltage triplet.
+
+Optional properties:
+- cpu-supply: Phandle to the CPU power supply.
+- core-supply: Phandle to the CORE power supply.
+- rtc-supply: Phandle to the RTC power supply, required only for Tegra20.
+
+Voltage supply requirements:
+- Tegra20:
+ CORE and RTC regulators must be coupled using the regulator-coupled-with
+ property and regulator-coupled-max-spread property must be set to no
+ more than 170mV.
+
+ See ../regulator/regulator.txt for more detail about the properties.
+
+- Tegra30:
+ CORE and CPU regulators must be coupled using the regulator-coupled-with
+ property and regulator-coupled-max-spread property must be set to no
+ more than 300mV. Each of CORE and CPU regulators must set
+ regulator-max-step-microvolt property to no more than 100mV.
+
+ See ../regulator/regulator.txt for more detail about the properties.
+
+
+Example:
+ regulators {
+ cpu_reg: regulator0 {
+ regulator-name = "vdd_cpu";
+ };
+
+ core_reg: regulator1 {
+ regulator-name = "vdd_core";
+ regulator-coupled-with = <&rtc_reg>;
+ regulator-coupled-max-spread = <170000>;
+ };
+
+ rtc_reg: regulator2 {
+ regulator-name = "vdd_rtc";
+ regulator-coupled-with = <&core_reg>;
+ regulator-coupled-max-spread = <170000>;
+ };
+ };
+
+ cpu0_opp_table: opp_table0 {
+ compatible = "operating-points-v2";
+
+ opp@456000000 {
+ clock-latency-ns = <125000>;
+ opp-microvolt = <825000 825000 1125000>;
+ opp-supported-hw = <0x03 0x0001>;
+ opp-hz = /bits/ 64 <456000000>;
+ };
+
+ ...
+ };
+
+ cpus {
+ cpu@0 {
+ compatible = "arm,cortex-a9";
+ clocks = <&tegra_car TEGRA20_CLK_PLL_X>,
+ <&tegra_car TEGRA20_CLK_PLL_P>,
+ <&tegra_car TEGRA20_CLK_CCLK>;
+ clock-names = "pll_x", "intermediate", "cclk";
+ operating-points-v2 = <&cpu0_opp_table>;
+ cpu-supply = <&cpu_reg>;
+ core-supply = <&core_reg>;
+ rtc-supply = <&rtc_reg>;
+ #cooling-cells = <2>;
+ };
+ };
--
2.19.0
