On Thu, 4 Oct 2018 09:14:36 +0000 Yogesh Narayan Gaur <yogeshnarayan.gaur@xxxxxxx> wrote: > Hi Boris, > > > -----Original Message----- > > From: Boris Brezillon [mailto:boris.brezillon@xxxxxxxxxxx] > > Sent: Thursday, October 4, 2018 2:35 PM > > To: Yogesh Narayan Gaur <yogeshnarayan.gaur@xxxxxxx> > > Cc: linux-mtd@xxxxxxxxxxxxxxxxxxx; marek.vasut@xxxxxxxxx; > > vigneshr@xxxxxx; linux-spi@xxxxxxxxxxxxxxx; > > devicetree@xxxxxxxxxxxxxxx; robh@xxxxxxxxxx; mark.rutland@xxxxxxx; > > shawnguo@xxxxxxxxxx; linux-arm- kernel@xxxxxxxxxxxxxxxxxxx; > > computersforpeace@xxxxxxxxx; frieder.schrempf@xxxxxxxxx; > > linux-kernel@xxxxxxxxxxxxxxx Subject: Re: [PATCH 1/4] spi: add > > support for octal I/O data transfer > > > > Hi Yogesh, > > > > On Thu, 4 Oct 2018 14:18:37 +0530 > > Yogesh Gaur <yogeshnarayan.gaur@xxxxxxx> wrote: > > > > > Add flags for Octal I/O data transfer > > > Required for the SPI controller which can do the data transfer > > > (TX/RX) on 8 data lines e.g. NXP FlexSPI controller. > > > SPI_TX_OCTAL: transmit with 8 wires > > > SPI_RX_OCTAL: receive with 8 wires > > > > > > Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@xxxxxxx> > > > --- > > > drivers/spi/spi.c | 6 ++++++ > > > include/linux/spi/spi.h | 2 ++ > > > 2 files changed, 8 insertions(+) > > > > > > diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c index > > > ec395a6..80f672f 100644 > > > --- a/drivers/spi/spi.c > > > +++ b/drivers/spi/spi.c > > > @@ -1573,6 +1573,9 @@ static int of_spi_parse_dt(struct > > > spi_controller *ctlr, > > struct spi_device *spi, > > > case 4: > > > spi->mode |= SPI_TX_QUAD; > > > break; > > > + case 8: > > > + spi->mode |= SPI_TX_OCTAL; > > > + break; > > > default: > > > dev_warn(&ctlr->dev, > > > "spi-tx-bus-width %d not > > > supported\n", @@ - > > 1591,6 +1594,9 @@ > > > static int of_spi_parse_dt(struct spi_controller *ctlr, struct > > > spi_device *spi, case 4: > > > spi->mode |= SPI_RX_QUAD; > > > break; > > > + case 8: > > > + spi->mode |= SPI_RX_OCTAL; > > > + break; > > > default: > > > dev_warn(&ctlr->dev, > > > "spi-rx-bus-width %d not > > > supported\n", diff -- > > git > > > a/include/linux/spi/spi.h b/include/linux/spi/spi.h index > > > a64235e..2d21307 100644 > > > --- a/include/linux/spi/spi.h > > > +++ b/include/linux/spi/spi.h > > > @@ -163,6 +163,8 @@ struct spi_device { > > > #define SPI_TX_QUAD > > > 0x200 /* transmit with 4 > > wires */ > > > #define SPI_RX_DUAL > > > 0x400 /* receive with 2 wires > > */ > > > #define SPI_RX_QUAD > > > 0x800 /* receive with 4 wires > > */ > > > +#define SPI_TX_OCTAL > > > 0x1000 /* transmit with 8 > > wires */ > > > +#define SPI_RX_OCTAL > > > 0x2000 /* receive with 8 wires > > */ > > > int irq; > > > void *controller_state; > > > void *controller_data; > > > > You're still not updating spi-mem.c to check those flags and > > SPI_MEM_MAX_BUSWIDTH is not updated to match the new limit (8 > > instead of 4). > > > Yes and its strange that my octal mode communication is working fine > without adding support in spi-mem.c and that's why this has been > missed from me. Are you based on top of spi-next?
