Hi Geert,
> Hi Lukasz,
>
> On Wed, Sep 26, 2018 at 4:33 PM Lukasz Majewski <lukma@xxxxxxx> wrote:
> > > On Tue, Sep 18, 2018 at 11:34:35AM +0200, Lukasz Majewski wrote:
> > > > This commit provides the description of new property:
> > > > "fsl,spi-slave-mode" which enables support for DSPI driver
> > > > working in slave mode.
> > > >
> > > > As the new compatible shall be used with SPI bus equipped with
> > > > master device a new "spidev" based node has been introduced to
> > > > avoid confusion.
> > > >
> > > > Signed-off-by: Lukasz Majewski <lukma@xxxxxxx>
> > > > ---
> > > > Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt | 8
> > > > ++++++++ 1 file changed, 8 insertions(+)
> > > >
> > > > diff --git
> > > > a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt
> > > > b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt index
> > > > 18eeafe359d8..b30af19a2bc5 100644 ---
> > > > a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt +++
> > > > b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt @@
> > > > -26,6 +26,7 @@ Optional SPI properties for slave nodes:
> > > > - fsl,spi-sck-cs-delay: a delay in nanoseconds between stopping
> > > > the clock signal and deactivating chip select, at the end of a
> > > > transfer.
> > > > - bus-num : the slave chip chipselect signal number.
> > > > +- fsl,spi-slave-mode: if present, controller runs in slave
> > > > mode.
> > >
> > > There's a standard property for this.
> >
> > I've just realised that there is "spi-slave" property in the
> > Documentation/devicetree/bindings/spi/spi-bus.txt
> >
> > I will convert the code to use it.
> >
> > >
> > > >
> > > > Example:
> > > >
> > > > @@ -56,6 +57,13 @@ dspi0@4002c000 {
> > > > fsl,spi-cs-sck-delay = <100>;
> > > > fsl,spi-sck-cs-delay = <50>;
> > > > };
> > > > +
> > > > + spidev3@1 {
> > > > + compatible = "fsl,vf610-dspi";
> > > > + spi-max-frequency = <30000000>;
> > > > + reg = <1>;
> > > > + fsl,spi-slave-mode;
> > >
> > > This doesn't look right for how slave mode is described.
> >
> > You mean that I shall replace fsl,spi-slave-mode; with "spi-slave" ?
> >
> > Or is there any other issue with this code?
>
> According to Documentation/devicetree/bindings/spi/spi-bus.txt:
> 1. "spi-slave" should be a property of the controller node, not of
> the slave node,
> 2. the slave node should be called "slave", without unit address,
> and without "reg" property.
Thanks for clarification.
>
> Gr{oetje,eeting}s,
>
> Geert
>
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd@xxxxxxx
Attachment:
pgpxST7mFPqS4.pgp
Description: OpenPGP digital signature
