This patchset mainly adds support for mt8183 IOMMU and SMI.
mt8183 has only one M4U like mt8173 and is also MTK IOMMU gen2 which
uses ARM Short-Descriptor translation table format.
The mt8183 M4U-SMI HW diagram is as below:
EMI
|
M4U
|
----------
| |
gals0-rx gals1-rx
| |
| |
gals0-tx gals1-tx
| |
------------
SMI Common
------------
|
+-----+-----+--------+-----+-----+-------+-------+
| | | | | | | |
| | gals-rx gals-rx | gals-rx gals-rx gals-rx
| | | | | | | |
| | | | | | | |
| | gals-tx gals-tx | gals-tx gals-tx gals-tx
| | | | | | | |
larb0 larb1 IPU0 IPU1 larb4 larb5 larb6 CCU
disp vdec img cam venc img cam
All the connections are HW fixed, SW can NOT adjust it.
Compared with mt8173, we add a GALS(Global Async Local Sync) module
between SMI-common and M4U, and additional GALS between larb2/3/5/6
and SMI-common. GALS can help synchronize for the modules in different
clock frequency, it can be seen as a "asynchronous fifo".
GALS can only help transfer the command/data while it doesn't have
the configuring register, thus it has the special "smi" clock and it
doesn't have the "apb" clock. From the diagram above, we add "gals0"
and "gals1" clocks for smi-common and add a "gals" clock for smi-larb.
>From the diagram above, IPU0/IPU1(Image Processor Unit) and CCU(Camera
Control Unit) is connected with smi-common directly, we can take them
as "larb2", "larb3" and "larb7", and their register spaces are
different with the normal larb.
This patchset is based on v4.19-rc1.
the patch 1/2/3/4/5/6 add the iommu/smi support for mt8183;
the patch 7/8/9/10 add mmu1 support;
the last patches contain some minor changes:
-patch 11 fix a issue.
-patch 12 improve the code flow(add shutdown).
-patch 13 cleanup some smi codes(delete need_larbid).
-patch 14 switch to SPDX license.
this patchset don't contain the dtsi part since it need depend on the
ccf and power-domain nodes which has not been accepted.
change notes:
v2: 1) Fix typo in the commit message of dt-binding.
2) Change larb2/larb3 to the special larbs.
3) Refactor the larb-id remapped array(larbid_remapped), then we
don't need add the new function(mtk_iommu_get_larbid).
4) Add a new patch for v7s two helpers(paddr_to_iopte and
iopte_to_paddr).
5) Change some comment for MTK 4GB mode.
v1:
http://lists.infradead.org/pipermail/linux-mediatek/2018-September/014881.html
Yong Wu (14):
dt-bindings: mediatek: Add binding for mt8183 IOMMU and SMI
iommu/mediatek: Use a struct as the platform data
memory: mtk-smi: Use a general config_port interface
iommu/io-pgtable-arm-v7s: Add paddr_to_iopte and iopte_to_paddr
helpers
iommu/io-pgtable-arm-v7s: Extend MediaTek 4GB Mode
iommu/mediatek: Add mt8183 IOMMU support
iommu/mediatek: Add mmu1 support
memory: mtk-smi: Invoke pm runtime_callback to enable clocks
memory: mtk-smi: Use a struct for the platform data for smi-common
memory: mtk-smi: Add bus_sel for mt8183
iommu/mediatek: Add VLD_PA_RANGE register backup when suspend
iommu/mediatek: Add shutdown callback
memory: mtk-smi: Get rid of need_larbid
iommu/mediatek: Switch to SPDX license identifier
.../devicetree/bindings/iommu/mediatek,iommu.txt | 15 +-
.../memory-controllers/mediatek,smi-common.txt | 11 +-
.../memory-controllers/mediatek,smi-larb.txt | 3 +
drivers/iommu/io-pgtable-arm-v7s.c | 75 ++++--
drivers/iommu/io-pgtable.h | 7 +-
drivers/iommu/mtk_iommu.c | 133 ++++++----
drivers/iommu/mtk_iommu.h | 23 +-
drivers/iommu/mtk_iommu_v1.c | 10 +-
drivers/memory/mtk-smi.c | 267 ++++++++++++++-------
include/dt-bindings/memory/mt2701-larb-port.h | 10 +-
include/dt-bindings/memory/mt8173-larb-port.h | 10 +-
include/dt-bindings/memory/mt8183-larb-port.h | 130 ++++++++++
include/soc/mediatek/smi.h | 10 +-
13 files changed, 492 insertions(+), 212 deletions(-)
create mode 100644 include/dt-bindings/memory/mt8183-larb-port.h
--
1.9.1
