Re: [PATCH] iio: magnetometer: Add support for PNI RM3100 9-axis magnetometer

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Sep 21, 2018 at 01:07:17PM +0800, Phil Reid wrote:
> G'day Song,
> 
> One more comment below.
> On 20/09/2018 9:46 PM, Peter Meerwald-Stadler wrote:
> > On Thu, 20 Sep 2018, Song Qiang wrote:
> > 
> > > PNI RM3100 magnetometer is a high resolution, large signal immunity
> > > magnetometer, composed of 3 single sensors and a processing chip.
> > > PNI is currently not in the vendors list, so this is also adding it.
> > 
> > comments below
> > 
> > > 
> > > Following functions are available:
> > >   - Single-shot measurement from
> > >     /sys/bus/iio/devices/iio:deviceX/in_magn_{axis}_raw
> > >   - Triggerd buffer measurement.
> > >   - Both i2c and spi interface are supported.
> > >   - Both interrupt and polling measurement is supported, depands on if
> > >     the 'interrupts' in DT is declared.
> > > 
> > > Signed-off-by: Song Qiang <songqiang1304521@xxxxxxxxx>
> > > ---
> > >   .../bindings/iio/magnetometer/pni,rm3100.txt  |  57 +++
> > >   .../devicetree/bindings/vendor-prefixes.txt   |   1 +
> > >   MAINTAINERS                                   |  10 +
> > >   drivers/iio/magnetometer/Kconfig              |  29 ++
> > >   drivers/iio/magnetometer/Makefile             |   4 +
> > >   drivers/iio/magnetometer/rm3100-core.c        | 399 ++++++++++++++++++
> > >   drivers/iio/magnetometer/rm3100-i2c.c         |  66 +++
> > >   drivers/iio/magnetometer/rm3100-spi.c         |  72 ++++
> > >   drivers/iio/magnetometer/rm3100.h             |  90 ++++
> > >   9 files changed, 728 insertions(+)
> > >   create mode 100644 Documentation/devicetree/bindings/iio/magnetometer/pni,rm3100.txt
> > >   create mode 100644 drivers/iio/magnetometer/rm3100-core.c
> > >   create mode 100644 drivers/iio/magnetometer/rm3100-i2c.c
> > >   create mode 100644 drivers/iio/magnetometer/rm3100-spi.c
> > >   create mode 100644 drivers/iio/magnetometer/rm3100.h
> > > 
> > > diff --git a/Documentation/devicetree/bindings/iio/magnetometer/pni,rm3100.txt b/Documentation/devicetree/bindings/iio/magnetometer/pni,rm3100.txt
> > > new file mode 100644
> > > index 000000000000..d0d2063e943f
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/iio/magnetometer/pni,rm3100.txt
> > > @@ -0,0 +1,57 @@
> > > +* PNI RM3100 9-axis magnetometer sensor
> > > +
> > > +I2C Bus:
> > > +
> > > +Required properties:
> > > +
> > > +- compatible : should be "pni,rm3100-i2c"
> > > +- reg : the I2C address of the magnetometer
> > > +
> > > +Optional properties:
> > > +
> > > +- interrupts: data ready (DRDY) from the chip.
> > > +  The interrupts can be triggered on rising edges.
> > > +
> > > +	Refer to interrupt-controller/interrupts.txt for generic
> > > +	interrupt client node bindings.
> > > +
> > > +- pinctrl-*: pinctrl setup for DRDY line.
> > > +
> > > +Example:
> > > +
> > > +rm3100: rm3100@20 {
> > > +	pinctrl-names = "default";
> > > +	pinctrl-0 = <&rm3100_pins>;
> > > +
> > > +	compatible = "pni,rm3100-i2c";
> > > +	reg = <0x20>;
> > > +	interrupt-parent = <&gpio0>;
> > > +	interrupts = <4 IRQ_TYPE_EDGE_RISING>;
> > > +};
> > > +
> > > +SPI Bus:
> > > +
> > > +Required properties:
> > > +
> > > +- compatible : should be "pni,rm3100-spi"
> > > +- reg : address of sensor, usually 0 or 1.
> > > +
> > > +Optional properties:
> > > +
> > > +- interrupts: data ready (DRDY) from the chip.
> > > +  The interrupts can be triggered on rising edges.
> > > +
> > > +	Refer to interrupt-controller/interrupts.txt for generic
> > > +	interrupt client node bindings.
> > > +
> > > +- pinctrl-*: pinctrl setup for DRDY line, depands on archtechture.
> > 
> > depends
> > architecture
> > 
> > > +
> > > +Example:
> > > +
> > > +rm3100: rm3100@0{
> > > +	compatible = "pni,rm3100-spi";
> > > +	reg = <0>;
> > > +
> > > +	interrupt-parent = <&gpio0>;
> > > +	interrupts = <4 IRQ_TYPE_EDGE_RISING>;
> > > +};
> > > diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
> > > index 41f0b97eb933..5bf3395fe9ae 100644
> > > --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
> > > +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
> > > @@ -288,6 +288,7 @@ pine64	Pine64
> > >   pixcir  PIXCIR MICROELECTRONICS Co., Ltd
> > >   plathome	Plat'Home Co., Ltd.
> > >   plda	PLDA
> > > +pni     PNI
> > >   portwell	Portwell Inc.
> > >   poslab	Poslab Technology Co., Ltd.
> > >   powervr	PowerVR (deprecated, use img)
> > > diff --git a/MAINTAINERS b/MAINTAINERS
> > > index 967ce8cdd1cc..30ee8cf98312 100644
> > > --- a/MAINTAINERS
> > > +++ b/MAINTAINERS
> > > @@ -11393,6 +11393,16 @@ M:	"Rafael J. Wysocki" <rafael.j.wysocki@xxxxxxxxx>
> > >   S:	Maintained
> > >   F:	drivers/pnp/
> > > +PNI RM3100 IIO DRIVER
> > > +M:	Song Qiang <songqiang1304521@xxxxxxxxx>
> > > +L:	linux-iio@xxxxxxxxxxxxxxx
> > > +S:	Maintained
> > > +F:	drivers/iio/magnetometer/rm3100-core.c
> > > +F:	drivers/iio/magnetometer/rm3100-i2c.c
> > > +F:	drivers/iio/magnetometer/rm3100-spi.c
> > > +F:	drivers/iio/magnetometer/rm3100.h
> > > +F:	Documentation/devicetree/bindings/iio/magnetometer/rm3100.txt
> > > +
> > >   POSIX CLOCKS and TIMERS
> > >   M:	Thomas Gleixner <tglx@xxxxxxxxxxxxx>
> > >   L:	linux-kernel@xxxxxxxxxxxxxxx
> > > diff --git a/drivers/iio/magnetometer/Kconfig b/drivers/iio/magnetometer/Kconfig
> > > index ed9d776d01af..f130b866a4fc 100644
> > > --- a/drivers/iio/magnetometer/Kconfig
> > > +++ b/drivers/iio/magnetometer/Kconfig
> > > @@ -175,4 +175,33 @@ config SENSORS_HMC5843_SPI
> > >   	  - hmc5843_core (core functions)
> > >   	  - hmc5843_spi (support for HMC5983)
> > > +config SENSORS_RM3100
> > > +	tristate
> > > +	select IIO_BUFFER
> > > +	select IIO_TRIGGERED_BUFFER
> > > +
> > > +config SENSORS_RM3100_I2C
> > > +	tristate "PNI RM3100 9-Axis Magnetometer (I2C)"
> > > +	depends on I2C
> > > +	select SENSORS_RM3100
> > > +	select REGMAP_I2C
> > > +	help
> > > +	  Say Y here to add support for the PNI RM3100 9-Axis Magnetometer.
> > > +
> > > +	  This driver can also be compiled as a module.
> > > +	  To compile this driver as a module, choose M here: the module
> > > +	  will be called rm3100-i2c.
> > > +
> > > +config SENSORS_RM3100_SPI
> > > +	tristate "PNI RM3100 9-Axis Magnetometer (SPI)"
> > > +	depends on SPI_MASTER
> > > +	select SENSORS_RM3100
> > > +	select REGMAP_SPI
> > > +	help
> > > +	  Say Y here to add support for the PNI RM3100 9-Axis Magnetometer.
> > > +
> > > +	  This driver can also be compiled as a module.
> > > +	  To compile this driver as a module, choose M here: the module
> > > +	  will be called rm3100-spi.
> > > +
> > >   endmenu
> > > diff --git a/drivers/iio/magnetometer/Makefile b/drivers/iio/magnetometer/Makefile
> > > index 664b2f866472..ba1bc34b82fa 100644
> > > --- a/drivers/iio/magnetometer/Makefile
> > > +++ b/drivers/iio/magnetometer/Makefile
> > > @@ -24,3 +24,7 @@ obj-$(CONFIG_IIO_ST_MAGN_SPI_3AXIS) += st_magn_spi.o
> > >   obj-$(CONFIG_SENSORS_HMC5843)		+= hmc5843_core.o
> > >   obj-$(CONFIG_SENSORS_HMC5843_I2C)	+= hmc5843_i2c.o
> > >   obj-$(CONFIG_SENSORS_HMC5843_SPI)	+= hmc5843_spi.o
> > > +
> > > +obj-$(CONFIG_SENSORS_RM3100)		+= rm3100-core.o
> > > +obj-$(CONFIG_SENSORS_RM3100_I2C)	+= rm3100-i2c.o
> > > +obj-$(CONFIG_SENSORS_RM3100_SPI)	+= rm3100-spi.o
> > > diff --git a/drivers/iio/magnetometer/rm3100-core.c b/drivers/iio/magnetometer/rm3100-core.c
> > > new file mode 100644
> > > index 000000000000..55d515e0fe67
> > > --- /dev/null
> > > +++ b/drivers/iio/magnetometer/rm3100-core.c
> > > @@ -0,0 +1,399 @@
> > > +// SPDX-License-Identifier: GPL-2.0+
> > > +/*
> > > + * PNI RM3100 9-axis geomagnetic sensor driver core.
> > > + *
> > > + * Copyright (C) 2018 Song Qiang <songqiang1304521@xxxxxxxxx>
> > > + *
> > > + * User Manual available at
> > > + * <https://www.pnicorp.com/download/rm3100-user-manual/>
> > > + *
> > > + * TODO: Scale channel, event generaton, pm.
> > 
> > at least read support for _SCALE is mandatory, IMHO
> > 
> > > + */
> > > +
> > > +#include <linux/delay.h>
> > > +#include <linux/interrupt.h>
> > > +#include <linux/slab.h>
> > > +
> > > +#include <linux/iio/iio.h>
> > > +#include <linux/iio/triggered_buffer.h>
> > > +#include <linux/iio/trigger_consumer.h>
> > > +#include <linux/iio/buffer.h>
> > > +#include <linux/iio/kfifo_buf.h>
> > > +
> > > +#include "rm3100.h"
> > > +
> > > +static const struct regmap_range rm3100_readable_ranges[] = {
> > > +		regmap_reg_range(RM_W_REG_START, RM_W_REG_END),
> > > +};
> > > +
> > > +const struct regmap_access_table rm3100_readable_table = {
> > 
> > static
> > 
> > > +		.yes_ranges = rm3100_readable_ranges,
> > > +		.n_yes_ranges = ARRAY_SIZE(rm3100_readable_ranges),
> > > +};
> > > +
> > > +static const struct regmap_range rm3100_writable_ranges[] = {
> > > +		regmap_reg_range(RM_R_REG_START, RM_R_REG_END),
> > > +};
> > > +
> > > +const struct regmap_access_table rm3100_writable_table = {
> > 
> > static
> > 
> > > +		.yes_ranges = rm3100_writable_ranges,
> > > +		.n_yes_ranges = ARRAY_SIZE(rm3100_writable_ranges),
> > > +};
> > > +
> > > +static const struct regmap_range rm3100_volatile_ranges[] = {
> > > +		regmap_reg_range(RM_V_REG_START, RM_V_REG_END),
> > > +};
> > > +
> > > +const struct regmap_access_table rm3100_volatile_table = {
> > 
> > static
> > 
> > > +		.yes_ranges = rm3100_volatile_ranges,
> > > +		.n_yes_ranges = ARRAY_SIZE(rm3100_volatile_ranges),
> > > +};
> > > +
> > > +static irqreturn_t rm3100_measurement_irq_handler(int irq, void *d)
> > > +{
> > > +	struct rm3100_data *data = d;
> > > +
> > > +	complete(&data->measuring_done);
> > > +
> > > +	return IRQ_HANDLED;
> > > +}
> > > +
> > > +static int rm3100_wait_measurement(struct rm3100_data *data)
> > > +{
> > > +	struct regmap *regmap = data->regmap;
> > > +	unsigned int val;
> > > +	u16 tries = 20;
> > 
> > why not use int for tries?
> > 
> > > +	int ret;
> > > +
> > > +	/* A read cycle of 400kbits i2c bus is about 20us, plus the time
> > > +	 * used for schduling, a read cycle of fast mode of this device
> > 
> > scheduling
> > 
> > > +	 * can reach 1.7ms, it may be possible for data arrives just
> > 
> > to arrive
> > 
> > > +	 * after we check the RM_REG_STATUS. In this case, irq_handler is
> > > +	 * called before measuring_done is reinitialized, it will wait
> > > +	 * forever for a data that has already been ready.
> > 
> > for data
> > 
> > > +	 * Reinitialize measuring_done before looking up makes sure we
> > > +	 * will always capture interrupt no matter when it happened.
> > > +	 */
> > > +	if (data->use_interrupt)
> > > +		reinit_completion(&data->measuring_done);
> > > +
> > > +	ret = regmap_read(regmap, RM_REG_STATUS, &val);
> > > +	if (ret < 0)
> > > +		return ret;
> > > +
> > > +	if ((val & RM_STATUS_DRDY) != RM_STATUS_DRDY) {
> > > +		if (data->use_interrupt) {
> > > +			ret = wait_for_completion_timeout(&data->measuring_done,
> > > +				msecs_to_jiffies(data->conversion_time));
> > > +			if (!ret)
> > > +				return -ETIMEDOUT;
> > > +		} else {
> > > +			do {
> > > +				ret = regmap_read(regmap, RM_REG_STATUS, &val);
> > > +				if (ret < 0)
> > > +					return ret;
> > > +
> > > +				if (val & RM_STATUS_DRDY)
> > > +					break;
> > > +
> > > +				usleep_range(1000, 5000);
> > > +			} while (--tries);
> > > +			if (!tries)
> > > +				return -ETIMEDOUT;
> > > +		}
> > > +	}
> > > +	return 0;
> > > +}
> > > +
> > > +static int rm3100_read_mag(struct rm3100_data *data, int idx, int *val)
> > > +{
> > > +	struct regmap *regmap = data->regmap;
> > > +	u8 buffer[3];
> > > +	int ret;
> > > +
> > > +	mutex_lock(&data->lock);
> > > +	ret = rm3100_wait_measurement(data);
> > > +	if (ret < 0) {
> > > +		mutex_unlock(&data->lock);
> > > +		return ret;
> > > +	}
> > > +
> > > +	ret = regmap_bulk_read(regmap, RM_REG_MX2 + 3 * idx, buffer, 3);
> > 
> > sizeof(buf)
> > 
> > > +	mutex_unlock(&data->lock);
> > > +	if (ret < 0)
> > > +		return ret;
> > > +
> > > +	*val = le32_to_cpu((buffer[0] << 16) + (buffer[1] << 8) + buffer[2]);
> > 
> > no need for le32_to_cpu()
> > 
> > > +	*val = sign_extend32(*val, 23);
> > > +
> > > +	return IIO_VAL_INT;
> > > +}
> > > +
> > > +#define RM_CHANNEL(axis, idx)					\
> > 
> > use RM3100_ prefix please
> > 
> > > +	{								\
> > > +		.type = IIO_MAGN,					\
> > > +		.modified = 1,						\
> > > +		.channel2 = IIO_MOD_##axis,				\
> > > +		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),		\
> > > +		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SAMP_FREQ),\
> > > +		.scan_index = idx,					\
> > > +		.scan_type = {						\
> > > +			.sign = 's',					\
> > > +			.realbits = 24,					\
> > > +			.storagebits = 32,				\
> > > +			.shift = 8,					\
> > > +			.endianness = IIO_LE,				\
> > > +		},							\
> > > +	}
> > > +
> > > +static const struct iio_chan_spec rm3100_channels[] = {
> > > +	RM_CHANNEL(X, 0),
> > > +	RM_CHANNEL(Y, 1),
> > > +	RM_CHANNEL(Z, 2),
> > > +	IIO_CHAN_SOFT_TIMESTAMP(3),
> > > +};
> > > +
> > > +static const unsigned long rm3100_scan_masks[] = {GENMASK(2, 0), 0};
> > > +
> > > +#define RM_SAMP_NUM	14
> > 
> > prefix
> > 
> > > +
> > > +/* Frequency : rm3100_samp_rates[][0].rm3100_samp_rates[][1]Hz.
> > > + * Time between reading: rm3100_sam_rates[][2]ms (The first on is actially 1.7).
> > 
> > one
> > actually
> > 1.7 what unit?
> > 
> > 
> > > + */
> > > +static const int rm3100_samp_rates[RM_SAMP_NUM][3] = {
> > > +	{600, 0, 2}, {300, 0, 3}, {150, 0, 7}, {75, 0, 13}, {37, 0, 27},
> > > +	{18, 0, 55}, {9, 0, 110}, {4, 500000, 220}, {2, 300000, 440},
> > > +	{1, 200000, 800}, {0, 600000, 1600}, {0, 300000, 3300},
> > > +	{0, 15000, 6700},  {0, 75000, 13000}
> > > +};
> > > +
> > > +static int rm3100_get_samp_freq(struct rm3100_data *data, int *val, int *val2)
> > > +{
> > > +	int ret;
> > > +	int tmp;
> > > +
> > > +	ret = regmap_read(data->regmap, RM_REG_TMRC, &tmp);
> > > +	if (ret < 0)
> > > +		return ret;
> > > +	*val = rm3100_samp_rates[tmp-RM_TMRC_OFFSET][0];
> > 
> > space around - operator
> > 
> > > +	*val2 = rm3100_samp_rates[tmp-RM_TMRC_OFFSET][1];
> > > +
> > > +	return IIO_VAL_INT_PLUS_MICRO;
> > > +}
> > > +
> > > +static int rm3100_set_samp_freq(struct rm3100_data *data, int val, int val2)
> > > +{
> > > +	struct regmap *regmap = data->regmap;
> > > +	int cycle_count;
> > > +	int ret;
> > > +	int i;
> > > +
> > > +	/* All cycle count registers use the same value. */
> > > +	ret = regmap_read(regmap, RM_REG_CCXL, &cycle_count);
> > 
> > check ret?
> > 
> > > +	if (cycle_count < 0)
> > > +		return cycle_count;
> > > +
> > > +	for (i = 0; i < RM_SAMP_NUM; i++) {
> > > +		if (val == rm3100_samp_rates[i][0] &&
> > > +			val2 == rm3100_samp_rates[i][1])
> > > +			break;
> > > +	}
> > > +
> > > +	if (i != RM_SAMP_NUM) {
> > > +		mutex_lock(&data->lock);
> > > +		ret = regmap_write(regmap, RM_REG_TMRC, i + RM_TMRC_OFFSET);
> > > +		if (ret < 0)
> > 
> > unlock?
> > 
> > > +			return ret;
> > > +
> > > +		/* Checking if cycle count registers need changing. */
> > > +		if (val == 600 && cycle_count == 200) {
> > > +			for (i = 0; i < 3; i++) {
> > > +				regmap_write(regmap, RM_REG_CCXL + 2 * i, 100);
> > > +				if (ret < 0)
> > 
> > unlock?
> > 
> > > +					return ret;
> > > +			}
> > > +		} else if (val != 600 && cycle_count == 100) {
> > > +			for (i = 0; i < 3; i++) {
> > > +				regmap_write(regmap, RM_REG_CCXL + 2 * i, 200);
> > > +				if (ret < 0)
> > 
> > unlock?
> > 
> > > +					return ret;
> > > +			}
> > > +		}
> > > +		/* Writing TMRC registers requires CMM reset. */
> > > +		ret = regmap_write(regmap, RM_REG_CMM, 0);
> > > +		if (ret < 0)
> > 
> > unlock?
> > 
> > > +			return ret;
> > > +		ret = regmap_write(regmap, RM_REG_CMM, RM_CMM_PMX |
> > > +			RM_CMM_PMY | RM_CMM_PMZ | RM_CMM_START);
> > > +		if (ret < 0)
> > 
> > unlock?
> > 
> > > +			return ret;
> > > +		mutex_unlock(&data->lock);
> > > +
> > > +		data->conversion_time = rm3100_samp_rates[i][2] + 3000;
> > > +		return 0;
> > > +	}
> > > +	return -EINVAL;
> > > +}
> > > +
> > > +static int rm3100_read_raw(struct iio_dev *indio_dev,
> > > +			   const struct iio_chan_spec *chan,
> > > +			   int *val, int *val2, long mask)
> > > +{
> > > +	struct rm3100_data *data = iio_priv(indio_dev);
> > > +	int ret;
> > > +
> > > +	switch (mask) {
> > > +	case IIO_CHAN_INFO_RAW:
> > > +		ret = iio_device_claim_direct_mode(indio_dev);
> > > +		if (ret < 0)
> > 
> > release_direct_mode() here?
> > 
> > > +			return ret;
> > > +		ret = rm3100_read_mag(data, chan->scan_index, val);
> > > +		iio_device_release_direct_mode(indio_dev);
> > > +
> > > +		return ret;
> > > +	case IIO_CHAN_INFO_SAMP_FREQ:
> > > +		return ret = rm3100_get_samp_freq(data, val, val2);
> > 
> > return ret = ???, just
> > return rm3100_...
> > 
> > > +	default:
> > > +		return -EINVAL;
> > > +	}
> > > +}
> > > +
> > > +static int rm3100_write_raw(struct iio_dev *indio_dev,
> > > +			    struct iio_chan_spec const *chan,
> > > +			    int val, int val2, long mask)
> > > +{
> > > +	struct rm3100_data *data = iio_priv(indio_dev);
> > > +	int ret;
> > > +
> > > +	switch (mask) {
> > > +	case IIO_CHAN_INFO_SAMP_FREQ:
> > > +		ret = rm3100_set_samp_freq(data, val, val2);
> > > +		if (ret < 0)
> > > +			return ret;
> > > +		return 0;
> > > +	default:
> > > +		return -EINVAL;
> > > +	}
> > > +
> > > +}
> > > +
> > > +static const struct iio_info rm3100_info = {
> > > +	.read_raw = rm3100_read_raw,
> > > +	.write_raw = rm3100_write_raw,
> > > +};
> > > +
> > > +static irqreturn_t rm3100_trigger_handler(int irq, void *p)
> > > +{
> > > +	struct iio_poll_func *pf = p;
> > > +	struct iio_dev *indio_dev = pf->indio_dev;
> > > +	struct rm3100_data *data = iio_priv(indio_dev);
> > > +	struct regmap *regmap = data->regmap;
> > > +	u8 *buffer;
> > > +	int ret;
> > > +	int i;
> > > +
> > > +	buffer = devm_kzalloc(data->dev, indio_dev->scan_bytes, GFP_KERNEL);
> > 
> > try to allocate the maximum needed amount of memory beforehand, in
> > _probe() perhaps
> > 
> > > +	if (!buffer)
> > > +		goto done;
> > > +
> > > +	mutex_lock(&data->lock);
> > > +	ret = rm3100_wait_measurement(data);
> > > +	if (ret < 0) {
> > > +		mutex_unlock(&data->lock);
> > > +		goto done;
> > > +	}
> > > +
> > > +	for (i = 0; i < 3; i++) {
> > > +		ret = regmap_bulk_read(regmap, RM_REG_MX2 + 3 * i,
> > > +				buffer + 4 * i, 3);
> > > +		if (ret < 0)
> > > +			return ret;
> > > +	}
> 
> Wouldn't it be better to read the 3 axis with one transaction here.
> And if required shuffle the data into the iio buffer.
> 
> 

Hi Phil,

That's surely something will make this code better!

But also, there is something worth discussing,
When triggered buffer is triggered here, I should push all the data into
userspace, and every time the buffer is enabled, the iio subsystem
automatically computes the alignment of my data. This sensor has 3
24bits channels, and my original thought of data alignment should be
like this because my machine is 32bits:
+----------+----+----+----+----+----+----+
| 3b(ytes) | 1b | 3b | 1b | 3b | 1b | 8b |
+----------+----+----+----+----+----+----+
3 bytes data and 1 byte for alignment, last 8 bytes for the timestamp.
Aligned to 4 bytes. 
But the actual layout is like this:
+----------+----+----+----+----+----+----+----+
| 3b(ytes) | 1b | 3b | 1b | 3b | 1b | 4b | 8b |
+----------+----+----+----+----+----+----+----+
Soon after I debugged the code of industrial io core I found that in the
iio_compute_scanbytes() in industialio-buffer.c, alignment was computed
each channel a time, and was aligned with the length of next channel. (eg:
In the last case, before the timestamp channel was appended, there are
12 bytes already in the buffer, to align to the timetamp which is 8 
bytes, it injected 4 bytes to make it 16, and then append timestamp. )
This leads to two questions:

1. I thought computer systems align their data in the memory for least
time access, shouldn't this always align to the bits of architecture,
like for a 32bits machine align to 4?? I'm a little confused here.
Jonathan must have considered something, Hoping to get some
explanations!

2. In this case I have 4 channels including the timetamp one, and I
thought it should be aligned like the first one. But actually it's
aligned like the second one, when I was testing the buffer, I got
confused, because the in_magn_x_type returned 24/32, 24/32, 24/32
and 64/64. If the iio core injected some empty bytes, shouldn't it
notify me? Or at least change the timestamp type in scan_bytes to
64/96>>0?? And when I only enabled two of three channels, the data
alignment in the buffer looks like this:
+----------+----+----+----+----+
| 3b(ytes) | 1b | 3b | 1b | 8b |
+----------+----+----+----+----+
Notice that 4 bytes have gone due to data of two channels have already
aligned to 8 bytes.
Hoping to get some answers, I'm very curious and interested about this!

yours,
Song Qiang

> > > +	mutex_unlock(&data->lock);
> > > +
> > > +	iio_push_to_buffers_with_timestamp(indio_dev, buffer,
> > > +			iio_get_time_ns(indio_dev));
> > > +done:
> > > +	iio_trigger_notify_done(indio_dev->trig);
> > > +
> > > +	return IRQ_HANDLED;
> > > +}
> > > +
> > > +int rm3100_common_probe(struct device *dev, struct regmap *regmap, int irq)
> > > +{
> > > +	struct iio_dev *indio_dev;
> > > +	struct rm3100_data *data;
> > > +	int tmp;
> > > +	int ret;
> > > +
> > > +	indio_dev = devm_iio_device_alloc(dev, sizeof(*data));
> > > +	if (!indio_dev)
> > > +		return -ENOMEM;
> > > +
> > > +	data = iio_priv(indio_dev);
> > > +	dev_set_drvdata(dev, indio_dev);
> > > +	data->dev = dev;
> > > +	data->regmap = regmap;
> > > +
> > > +	mutex_init(&data->lock);
> > > +
> > > +	indio_dev->dev.parent = dev;
> > > +	indio_dev->name = "rm3100";
> > > +	indio_dev->info = &rm3100_info;
> > > +	indio_dev->channels = rm3100_channels;
> > > +	indio_dev->num_channels = ARRAY_SIZE(rm3100_channels);
> > > +	indio_dev->modes = INDIO_DIRECT_MODE;
> > > +	indio_dev->available_scan_masks = rm3100_scan_masks;
> > > +
> > > +	if (!irq)
> > > +		data->use_interrupt = false;
> > > +	else {
> > > +		data->use_interrupt = true;
> > > +		ret = devm_request_irq(dev,
> > > +			irq,
> > > +			rm3100_measurement_irq_handler,
> > > +			IRQF_TRIGGER_RISING,
> > > +			indio_dev->name,
> > > +			data);
> > > +		if (ret < 0) {
> > > +			dev_err(dev,
> > > +			"request irq line failed.");
> > 
> > \n
> > 
> > > +			return -ret;
> > > +		}
> > > +		init_completion(&data->measuring_done);
> > > +	}
> > > +
> > > +	ret = iio_triggered_buffer_setup(indio_dev, NULL,
> > > +					rm3100_trigger_handler, NULL);
> > > +	if (ret < 0)
> > > +		return ret;
> > > +
> > > +	/* 3sec more wait time. */
> > > +	ret = regmap_read(data->regmap, RM_REG_TMRC, &tmp);
> > 
> > check ret
> > 
> > > +	data->conversion_time = rm3100_samp_rates[tmp-RM_TMRC_OFFSET][2] + 3000;
> > > +
> > > +	/* Starting all channels' conversion. */
> > > +	ret = regmap_write(regmap, RM_REG_CMM,
> > > +		RM_CMM_PMX | RM_CMM_PMY | RM_CMM_PMZ | RM_CMM_START);
> > > +	if (ret < 0)
> > > +		return ret;
> > > +
> > > +	return devm_iio_device_register(dev, indio_dev);
> > > +}
> > > +EXPORT_SYMBOL(rm3100_common_probe);
> > > +
> > > +int rm3100_common_remove(struct device *dev)
> > > +{
> > > +	struct iio_dev *indio_dev = dev_get_drvdata(dev);
> > > +	struct rm3100_data *data = iio_priv(indio_dev);
> > > +	struct regmap *regmap = data->regmap;
> > > +
> > > +	regmap_write(regmap, RM_REG_CMM, 0x00);
> > > +
> > > +	return 0;
> > > +}
> > > +EXPORT_SYMBOL(rm3100_common_remove);
> > > +
> > > +MODULE_AUTHOR("Song Qiang <songqiang1304521@xxxxxxxxx>");
> > > +MODULE_DESCRIPTION("PNI RM3100 9-axis magnetometer i2c driver");
> > > +MODULE_LICENSE("GPL v2");
> > > diff --git a/drivers/iio/magnetometer/rm3100-i2c.c b/drivers/iio/magnetometer/rm3100-i2c.c
> > > new file mode 100644
> > > index 000000000000..b50dc5b1b30b
> > > --- /dev/null
> > > +++ b/drivers/iio/magnetometer/rm3100-i2c.c
> > > @@ -0,0 +1,66 @@
> > > +// SPDX-License-Identifier: GPL-2.0+
> > > +/*
> > > + * Support for PNI RM3100 9-axis geomagnetic sensor a i2c bus.
> > > + *
> > > + * Copyright (C) 2018 Song Qiang <songqiang1304521@xxxxxxxxx>
> > > + *
> > > + * User Manual available at
> > > + * <https://www.pnicorp.com/download/rm3100-user-manual/>
> > > + *
> > > + * i2c slave address 0x20 + SA1 << 1 + SA0.
> > > + */
> > > +
> > > +#include <linux/i2c.h>
> > > +
> > > +#include "rm3100.h"
> > > +
> > > +static const struct regmap_config rm3100_regmap_config = {
> > > +		.reg_bits = 8,
> > > +		.val_bits = 8,
> > > +
> > > +		.rd_table = &rm3100_readable_table,
> > > +		.wr_table = &rm3100_writable_table,
> > > +		.volatile_table = &rm3100_volatile_table,
> > > +
> > > +		.cache_type = REGCACHE_RBTREE,
> > > +};
> > > +
> > > +static int rm3100_probe(struct i2c_client *client)
> > > +{
> > > +	struct regmap *regmap;
> > > +
> > > +	if (!i2c_check_functionality(client->adapter,
> > > +		I2C_FUNC_SMBUS_READ_I2C_BLOCK | I2C_FUNC_SMBUS_BYTE_DATA))
> > > +		return -EOPNOTSUPP;
> > > +
> > > +	regmap =  devm_regmap_init_i2c(client, &rm3100_regmap_config);
> > > +	if (IS_ERR(regmap))
> > > +		return PTR_ERR(regmap);
> > > +
> > > +	return rm3100_common_probe(&client->dev, regmap, client->irq);
> > > +}
> > > +
> > > +static int rm3100_remove(struct i2c_client *client)
> > > +{
> > > +	return rm3100_common_remove(&client->dev);
> > > +}
> > > +
> > > +static const struct of_device_id rm3100_dt_match[] = {
> > > +	{ .compatible = "pni,rm3100-i2c", },
> > > +	{ }
> > > +};
> > > +MODULE_DEVICE_TABLE(of, rm3100_dt_match);
> > > +
> > > +static struct i2c_driver rm3100_driver = {
> > > +	.driver = {
> > > +		.name = "rm3100-i2c",
> > > +		.of_match_table = rm3100_dt_match,
> > > +	},
> > > +	.probe_new = rm3100_probe,
> > > +	.remove = rm3100_remove,
> > > +};
> > > +module_i2c_driver(rm3100_driver);
> > > +
> > > +MODULE_AUTHOR("Song Qiang <songqiang1304521@xxxxxxxxx>");
> > > +MODULE_DESCRIPTION("PNI RM3100 9-axis magnetometer i2c driver");
> > > +MODULE_LICENSE("GPL v2");
> > > diff --git a/drivers/iio/magnetometer/rm3100-spi.c b/drivers/iio/magnetometer/rm3100-spi.c
> > > new file mode 100644
> > > index 000000000000..2c7dd9e3a1a2
> > > --- /dev/null
> > > +++ b/drivers/iio/magnetometer/rm3100-spi.c
> > > @@ -0,0 +1,72 @@
> > > +// SPDX-License-Identifier: GPL-2.0+
> > > +/*
> > > + * Support for PNI RM3100 9-axis geomagnetic sensor a spi bus.
> > > + *
> > > + * Copyright (C) 2018 Song Qiang <songqiang1304521@xxxxxxxxx>
> > > + *
> > > + * User Manual available at
> > > + * <https://www.pnicorp.com/download/rm3100-user-manual/>
> > > + */
> > > +
> > > +#include <linux/spi/spi.h>
> > > +
> > > +#include "rm3100.h"
> > > +
> > > +static const struct regmap_config rm3100_regmap_config = {
> > > +		.reg_bits = 8,
> > > +		.val_bits = 8,
> > > +
> > > +		.rd_table = &rm3100_readable_table,
> > > +		.wr_table = &rm3100_writable_table,
> > > +		.volatile_table = &rm3100_volatile_table,
> > > +
> > > +		.read_flag_mask = 0x80,
> > > +
> > > +		.cache_type = REGCACHE_RBTREE,
> > > +};
> > > +
> > > +static int rm3100_probe(struct spi_device *spi)
> > > +{
> > > +	struct regmap *regmap;
> > > +	int ret;
> > > +
> > > +	/* Actually this device supports both mode 0 and mode 3. */
> > > +	spi->mode = SPI_MODE_0;
> > > +	/* data rates cannot exceeds 1Mbits. */
> > 
> > exceed
> > 
> > > +	spi->max_speed_hz = 1000000;
> > > +	spi->bits_per_word = 8;
> > > +	ret = spi_setup(spi);
> > > +	if (ret)
> > > +		return ret;
> > > +
> > > +	regmap =  devm_regmap_init_spi(spi, &rm3100_regmap_config);
> > > +	if (IS_ERR(regmap))
> > > +		return PTR_ERR(regmap);
> > > +
> > > +	return rm3100_common_probe(&spi->dev, regmap, spi->irq);
> > > +}
> > > +
> > > +static int rm3100_remove(struct spi_device *spi)
> > > +{
> > > +	return rm3100_common_remove(&spi->dev);
> > > +}
> > > +
> > > +static const struct of_device_id rm3100_dt_match[] = {
> > > +	{ .compatible = "pni,rm3100-spi", },
> > > +	{ }
> > > +};
> > > +MODULE_DEVICE_TABLE(of, rm3100_dt_match);
> > > +
> > > +static struct spi_driver rm3100_driver = {
> > > +		.driver = {
> > > +				.name = "rm3100-spi",
> > > +				.of_match_table = rm3100_dt_match,
> > > +		},
> > > +		.probe = rm3100_probe,
> > > +		.remove = rm3100_remove,
> > > +};
> > > +module_spi_driver(rm3100_driver);
> > > +
> > > +MODULE_AUTHOR("Song Qiang <songqiang1304521@xxxxxxxxx>");
> > > +MODULE_DESCRIPTION("PNI RM3100 9-axis magnetometer spi driver");
> > > +MODULE_LICENSE("GPL v2");
> > > diff --git a/drivers/iio/magnetometer/rm3100.h b/drivers/iio/magnetometer/rm3100.h
> > > new file mode 100644
> > > index 000000000000..5e30bc0f5149
> > > --- /dev/null
> > > +++ b/drivers/iio/magnetometer/rm3100.h
> > > @@ -0,0 +1,90 @@
> > > +/* SPDX-License-Identifier: GPL-2.0+ */
> > > +/*
> > > + * Header file for PNI RM3100 driver
> > > + *
> > > + * Copyright (C) 2018 Song Qiang <songqiang1304521@xxxxxxxxx>
> > > + */
> > > +
> > > +#ifndef RM3100_CORE_H
> > > +#define RM3100_CORE_H
> > > +
> > > +#include <linux/module.h>
> > > +#include <linux/regmap.h>
> > > +
> > > +#define RM_REG_REV_ID		0x36
> > > +
> > > +/* Cycle Count Registers MSBs and LSBs. */
> > > +#define RM_REG_CCXM		0x04
> > > +#define RM_REG_CCXL		0x05
> > > +#define RM_REG_CCYM		0x06
> > > +#define RM_REG_CCYL		0x07
> > > +#define RM_REG_CCZM		0x08
> > > +#define RM_REG_CCZL		0x09
> > > +
> > > +/* Single Measurement Mode register. */
> > > +#define RM_REG_POLL		0x00
> > > +#define RM_POLL_PMX		BIT(4)
> > > +#define RM_POLL_PMY		BIT(5)
> > > +#define RM_POLL_PMZ		BIT(6)
> > > +
> > > +/* Continues Measurement Mode register. */
> > > +#define RM_REG_CMM		0x01
> > > +#define RM_CMM_START		BIT(0)
> > > +#define RM_CMM_DRDM		BIT(2)
> > > +#define RM_CMM_PMX		BIT(4)
> > > +#define RM_CMM_PMY		BIT(5)
> > > +#define RM_CMM_PMZ		BIT(6)
> > > +
> > > +/* TiMe Rate Configuration register. */
> > > +#define RM_REG_TMRC		0x0B
> > > +#define RM_TMRC_OFFSET		0x92
> > > +
> > > +/* Result Status register. */
> > > +#define RM_REG_STATUS		0x34
> > > +#define RM_STATUS_DRDY		BIT(7)
> > > +
> > > +/* Measurement result registers. */
> > > +#define RM_REG_MX2		0x24
> > > +#define RM_REG_MX1		0x25
> > > +#define RM_REG_MX0		0x26
> > > +#define RM_REG_MY2		0x27
> > > +#define RM_REG_MY1		0x28
> > > +#define RM_REG_MY0		0x29
> > > +#define RM_REG_MZ2		0x2a
> > > +#define RM_REG_MZ1		0x2b
> > > +#define RM_REG_MZ0		0x2c
> > > +
> > > +#define RM_REG_HSHAKE		0x35
> > > +
> > > +#define RM_W_REG_START		RM_REG_POLL
> > > +#define RM_W_REG_END		RM_REG_REV_ID
> > > +#define RM_R_REG_START		RM_REG_POLL
> > > +#define RM_R_REG_END		RM_REG_HSHAKE
> > > +#define RM_V_REG_START		RM_REG_MX2
> > > +#define RM_V_REG_END		RM_REG_HSHAKE
> > > +
> > > +/* Built-In Self Test reigister. */
> > > +#define RM_REG_BIST		0x33
> > > +
> > > +struct rm3100_data {
> > > +	struct device *dev;
> > > +	struct regmap *regmap;
> > > +	struct completion measuring_done;
> > > +	bool use_interrupt;
> > > +
> > > +	int conversion_time;
> > > +
> > > +	/* To protect consistency of every measurement and sampling
> > > +	 * frequency change operations.
> > > +	 */
> > > +	struct mutex lock;
> > > +};
> > > +
> > > +extern const struct regmap_access_table rm3100_readable_table;
> > > +extern const struct regmap_access_table rm3100_writable_table;
> > > +extern const struct regmap_access_table rm3100_volatile_table;
> > > +
> > > +int rm3100_common_probe(struct device *dev, struct regmap *regmap, int irq);
> > > +int rm3100_common_remove(struct device *dev);
> > > +
> > > +#endif /* RM3100_CORE_H */
> > > 
> > 
> 
> 
> -- 
> Regards
> Phil Reid
> 



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux