Signed-off-by: Karsten Mueller <mueller.k@xxxxxxxxxxx>
---
.../bindings/power/supply/bq2416x.txt | 75 +++++++++++++++++++
1 file changed, 75 insertions(+)
create mode 100644 Documentation/devicetree/bindings/power/supply/bq2416x.txt
diff --git a/Documentation/devicetree/bindings/power/supply/bq2416x.txt b/Documentation/devicetree/bindings/power/supply/bq2416x.txt
new file mode 100644
index 000000000..742d41642
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/bq2416x.txt
@@ -0,0 +1,75 @@
+Binding for TI bq2416x Li-Ion Charger
+
+Required properties:
+====================
+- compatible: one of the following:
+ * "ti,bq24160"
+ * "ti,bq24160a"
+ * "ti,bq24161"
+ * "ti,bq24161b"
+ * "ti,bq24163"
+ * "ti,bq24168"
+
+- reg: I2C address of the device.
+- interrupt-parent: The IRQ controller (phandle) connected to the INT pin of
+ the bq2416x
+- interrupts: The IRQ number assigned for INT pin.
+
+Optional properties:
+====================
+
+- ti,in-current-limit-microamp: IN source current limit.
+ Possible values: 1500000 (default), 2500000
+
+- ti,usb-current-limit-microamp: USB source current limit.
+ If not specified, auto detection of USB (D+/D- based) is used (for
+ BQ24160/0A/3 only) or settings of default mode are kept (BQ24161/1B/8).
+ Both pre-select only 100 mA or 1500 mA (refer to datasheet).
+ Possible values: 100000, 150000, 500000, 800000, 90000, 1500000
+
+- ti,usb-dpm-voltage-microvolt: USB threshold for dynamic power path management.
+ Configures the threshold input voltage (usb input) for the dynamic power
+ path management. If not specified a default of 4,200,000 (= 4.2V) is
+ used.
+
+- ti,in-dpm-voltage-microvolt: IN threshold for dynamic power path management.
+ Configures the threshold input voltage (in input) for the dynamic power
+ path management. If not specified a default of 4,200,000 (= 4.2V) is
+ used.
+
+- monitored-battery: phandle of battery information devicetree node
+ If not specified, no battery is assumed (charge disable, nobat operation
+ mode, no NTC check of battery), Vsys output voltage is set to 4.2V. The
+ charger uses the following battery properties:
+ + constant_charge_current_max_microamp: maximum current in fast charge
+ mode
+ + constant_charge_voltage_max_microvolt: maximum constant charging
+ voltage / output voltage (refer to datasheet)
+ + charge-term-current-microamp: a charge cycle terminates when the
+ battery voltage is above recharge threshold, and the current is below
+ this setting (typically 10% of battery capacity). If not specified,
+ termination of current detection is disabled (refer to datasheet).
+
+Example:
+========
+
+bat: battery {
+ compatible = "simple-battery";
+ charge-term-current-microamp = <128000>;
+ constant-charge-current-max-microamp = <900000>;
+ constant-charge-voltage-max-microvolt = <4200000>;
+ };
+
+bq24160@6b {
+ compatible = "ti,bq24160";
+ reg = <0x6b>;
+
+ interrupt-parent = <&gpio5>;
+ interrupts = <31 IRQ_TYPE_EDGE_RISING>;
+
+ monitored-battery = <&bat>;
+ ti,in-current-limit-microamp = <1500000>;
+ ti,usb-current-limit-microamp = <500000>;
+ ti,usb-dpm-voltage-microvolt = <4300000>;
+ ti,in-dpm-voltage-microvolt = <4300000>;
+};
--
2.17.1
