This patch adds the binding documentation for Spreadtrum SC27XX series PMICs
fuel gauge unit device, which is used to calculate the battery capacity.
Signed-off-by: Baolin Wang <baolin.wang@xxxxxxxxxx>
---
.../devicetree/bindings/power/supply/sc27xx-fg.txt | 55 ++++++++++++++++++++
1 file changed, 55 insertions(+)
create mode 100644 Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt
diff --git a/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt b/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt
new file mode 100644
index 0000000..7447bae
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt
@@ -0,0 +1,55 @@
+Spreadtrum SC27XX PMICs Fuel Gauge Unit Power Supply Bindings
+
+Required properties:
+- compatible: Should be one of the following:
+ "sprd,sc2720-fgu",
+ "sprd,sc2721-fgu",
+ "sprd,sc2723-fgu",
+ "sprd,sc2730-fgu",
+ "sprd,sc2731-fgu".
+- reg: The address offset of fuel gauge unit.
+- bat-detect-gpio: GPIO for battery detection.
+- io-channels: Specify the IIO ADC channel to get temperature.
+- io-channel-names: Should be "bat-temp".
+- sprd,inner-resist: Specify the the battery inner resistance (mOhm).
+- sprd,ocv-cap-table: Provide the battery capacity percent with corresponding
+ open circuit voltage (ocv) of the battery, which is used to look up current
+ battery capacity according to current baterry ocv values.
+- monitored-battery: Phandle of battery characteristics devicetree node.
+ The fuel gauge uses the following battery properties:
+- charge-full-design-microamp-hours: battery design capacity.
+- constant-charge-voltage-max-microvolt: maximum constant input voltage.
+ See Documentation/devicetree/bindings/power/supply/battery.txt
+
+Example:
+
+ bat: battery {
+ compatible = "simple-battery";
+ charge-full-design-microamp-hours = <1900000>;
+ constant-charge-voltage-max-microvolt = <4350000>;
+ ......
+ };
+
+ sc2731_pmic: pmic@0 {
+ compatible = "sprd,sc2731";
+ reg = <0>;
+ spi-max-frequency = <26000000>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fgu@a00 {
+ compatible = "sprd,sc2731-fgu";
+ reg = <0xa00>;
+ bat-detect-gpio = <&pmic_eic 9 GPIO_ACTIVE_HIGH>;
+ io-channels = <&pmic_adc 5>;
+ io-channel-names = "bat-temp";
+ sprd,inner-resist = <250>;
+ sprd,ocv-cap-table = <4185 100>, <4113 95>, <4066 90>, <4022 85>, <3983 80>, <3949 75>, <3917 70>,
+ <3889 65>, <3864 60>, <3835 55>, <3805 50>, <3787 45>, <3777 40>, <3773 35>, <3770 30>,
+ <3765 25>, <3752 20>, <3724 15>, <3680 10>, <3605 5>, <3400 0>;
+ monitored-battery = <&bat>;
+ };
+ };
--
1.7.9.5
