The PPC476GTR SoC supports message signalled interrupts (MSI) by writing
to special addresses within the High Speed Transfer Assist (HSTA) module.
This patch adds support for PCI MSI with a new system device. The DMA
window is also updated to allow access to the entire 42-bit address range
to allow PCI devices write access to the HSTA module.
Signed-off-by: Alistair Popple <alistair@xxxxxxxxxxxx>
---
.../devicetree/bindings/powerpc/4xx/hsta.txt | 19 ++
arch/powerpc/boot/dts/akebono.dts | 46 ++++-
arch/powerpc/boot/treeboot-akebono.c | 15 --
arch/powerpc/platforms/44x/Kconfig | 2 +
arch/powerpc/sysdev/Kconfig | 6 +
arch/powerpc/sysdev/Makefile | 1 +
arch/powerpc/sysdev/ppc4xx_hsta_msi.c | 215 +++++++++++++++++++++
arch/powerpc/sysdev/ppc4xx_pci.c | 8 +-
8 files changed, 287 insertions(+), 25 deletions(-)
create mode 100644 Documentation/devicetree/bindings/powerpc/4xx/hsta.txt
create mode 100644 arch/powerpc/sysdev/ppc4xx_hsta_msi.c
diff --git a/Documentation/devicetree/bindings/powerpc/4xx/hsta.txt b/Documentation/devicetree/bindings/powerpc/4xx/hsta.txt
new file mode 100644
index 0000000..c737c83
--- /dev/null
+++ b/Documentation/devicetree/bindings/powerpc/4xx/hsta.txt
@@ -0,0 +1,19 @@
+
+ppc476gtr High Speed Serial Assist (HSTA) node
+==============================================
+
+The 476gtr SoC contains a high speed serial assist module attached
+between the plb4 and plb6 system buses to provide high speed data
+transfer between memory and system peripherals as well as support for
+PCI message signalled interrupts.
+
+Currently only the MSI support is used by Linux using the following
+device tree entries:
+
+Require properties:
+- compatible : "ibm,476gtr-hsta-msi", "ibm,hsta-msi"
+- reg : register mapping for the HSTA MSI space
+- interrupt-parent : parent controller for mapping interrupts
+- interrupts : ordered interrupt mapping for each MSI in the register
+ space. The first interrupt should be associated with a
+ register offset of 0x00, the second to 0x10, etc.
diff --git a/arch/powerpc/boot/dts/akebono.dts b/arch/powerpc/boot/dts/akebono.dts
index 96ac13b..f92ecfe 100644
--- a/arch/powerpc/boot/dts/akebono.dts
+++ b/arch/powerpc/boot/dts/akebono.dts
@@ -82,6 +82,28 @@
ranges;
clock-frequency = <200000000>; // 200Mhz
+ HSTA0: hsta@310000e0000 {
+ compatible = "ibm,476gtr-hsta-msi", "ibm,hsta-msi";
+ reg = <0x310 0x000e0000 0x0 0xf0>;
+ interrupt-parent = <&MPIC>;
+ interrupts = <108 0
+ 109 0
+ 110 0
+ 111 0
+ 112 0
+ 113 0
+ 114 0
+ 115 0
+ 116 0
+ 117 0
+ 118 0
+ 119 0
+ 120 0
+ 121 0
+ 122 0
+ 123 0>;
+ };
+
MAL0: mcmal {
compatible = "ibm,mcmal-476gtr", "ibm,mcmal2";
dcr-reg = <0xc0000000 0x062>;
@@ -242,8 +264,10 @@
ranges = <0x02000000 0x00000000 0x80000000 0x00000110 0x80000000 0x0 0x80000000
0x01000000 0x0 0x0 0x00000140 0x0 0x0 0x00010000>;
- /* Inbound starting at 0 to memsize filled in by zImage */
- dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x0>;
+ /* Inbound starting at 0x0 to 0x40000000000. In order to use MSI
+ * PCI devices must be able to write to the HSTA module.
+ */
+ dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x400 0x0>;
/* This drives busses 0 to 0xf */
bus-range = <0x0 0xf>;
@@ -280,8 +304,10 @@
ranges = <0x02000000 0x00000000 0x80000000 0x00000210 0x80000000 0x0 0x80000000
0x01000000 0x0 0x0 0x00000240 0x0 0x0 0x00010000>;
- /* Inbound starting at 0 to memsize filled in by zImage */
- dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x0>;
+ /* Inbound starting at 0x0 to 0x40000000000. In order to use MSI
+ * PCI devices must be able to write to the HSTA module.
+ */
+ dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x400 0x0>;
/* This drives busses 0 to 0xf */
bus-range = <0x0 0xf>;
@@ -318,8 +344,10 @@
ranges = <0x02000000 0x00000000 0x80000000 0x00000190 0x80000000 0x0 0x80000000
0x01000000 0x0 0x0 0x000001c0 0x0 0x0 0x00010000>;
- /* Inbound starting at 0 to memsize filled in by zImage */
- dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x0>;
+ /* Inbound starting at 0x0 to 0x40000000000. In order to use MSI
+ * PCI devices must be able to write to the HSTA module.
+ */
+ dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x400 0x0>;
/* This drives busses 0 to 0xf */
bus-range = <0x0 0xf>;
@@ -356,8 +384,10 @@
ranges = <0x02000000 0x00000000 0x80000000 0x00000290 0x80000000 0x0 0x80000000
0x01000000 0x0 0x0 0x000002c0 0x0 0x0 0x00010000>;
- /* Inbound starting at 0 to memsize filled in by zImage */
- dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x0>;
+ /* Inbound starting at 0x0 to 0x40000000000. In order to use MSI
+ * PCI devices must be able to write to the HSTA module.
+ */
+ dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x400 0x0>;
/* This drives busses 0 to 0xf */
bus-range = <0x0 0xf>;
diff --git a/arch/powerpc/boot/treeboot-akebono.c b/arch/powerpc/boot/treeboot-akebono.c
index 070a20f..b73174c 100644
--- a/arch/powerpc/boot/treeboot-akebono.c
+++ b/arch/powerpc/boot/treeboot-akebono.c
@@ -75,24 +75,9 @@ static void ibm_akebono_fixups(void)
{
void *emac;
u32 reg;
- void *devp = finddevice("/");
- u32 dma_ranges[7];
dt_fixup_memory(0x0ULL, ibm_akebono_memsize);
- while ((devp = find_node_by_devtype(devp, "pci"))) {
- if (getprop(devp, "dma-ranges", dma_ranges,
- sizeof(dma_ranges)) < 0) {
- printf("%s: Failed to get dma-ranges\r\n", __func__);
- continue;
- }
-
- dma_ranges[5] = ibm_akebono_memsize >> 32;
- dma_ranges[6] = ibm_akebono_memsize & 0xffffffffUL;
-
- setprop(devp, "dma-ranges", dma_ranges, sizeof(dma_ranges));
- }
-
/* Fixup the SD timeout frequency */
mtdcrx(CCTL0_MCO4, 0x1);
diff --git a/arch/powerpc/platforms/44x/Kconfig b/arch/powerpc/platforms/44x/Kconfig
index b0202d8..8beec7d 100644
--- a/arch/powerpc/platforms/44x/Kconfig
+++ b/arch/powerpc/platforms/44x/Kconfig
@@ -206,6 +206,8 @@ config AKEBONO
select SWIOTLB
select 476FPE
select PPC4xx_PCI_EXPRESS
+ select PCI_MSI
+ select PPC4xx_HSTA_MSI
select I2C
select I2C_IBM_IIC
select NETDEVICES
diff --git a/arch/powerpc/sysdev/Kconfig b/arch/powerpc/sysdev/Kconfig
index 7baa70d..a19332a 100644
--- a/arch/powerpc/sysdev/Kconfig
+++ b/arch/powerpc/sysdev/Kconfig
@@ -7,6 +7,12 @@ config PPC4xx_PCI_EXPRESS
depends on PCI && 4xx
default n
+config PPC4xx_HSTA_MSI
+ bool
+ depends on PCI_MSI
+ depends on PCI && 4xx
+ default n
+
config PPC4xx_MSI
bool
depends on PCI_MSI
diff --git a/arch/powerpc/sysdev/Makefile b/arch/powerpc/sysdev/Makefile
index afbcc37..f7cb2a1 100644
--- a/arch/powerpc/sysdev/Makefile
+++ b/arch/powerpc/sysdev/Makefile
@@ -45,6 +45,7 @@ obj-$(CONFIG_OF_RTC) += of_rtc.o
ifeq ($(CONFIG_PCI),y)
obj-$(CONFIG_4xx) += ppc4xx_pci.o
endif
+obj-$(CONFIG_PPC4xx_HSTA_MSI) += ppc4xx_hsta_msi.o
obj-$(CONFIG_PPC4xx_MSI) += ppc4xx_msi.o
obj-$(CONFIG_PPC4xx_CPM) += ppc4xx_cpm.o
obj-$(CONFIG_PPC4xx_GPIO) += ppc4xx_gpio.o
diff --git a/arch/powerpc/sysdev/ppc4xx_hsta_msi.c b/arch/powerpc/sysdev/ppc4xx_hsta_msi.c
new file mode 100644
index 0000000..11c8884
--- /dev/null
+++ b/arch/powerpc/sysdev/ppc4xx_hsta_msi.c
@@ -0,0 +1,215 @@
+/*
+ * MSI support for PPC4xx SoCs using High Speed Transfer Assist (HSTA) for
+ * generation of the interrupt.
+ *
+ * Copyright © 2013 Alistair Popple <alistair@xxxxxxxxxxxx> IBM Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/msi.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/pci.h>
+#include <linux/semaphore.h>
+#include <asm/msi_bitmap.h>
+
+struct ppc4xx_hsta_msi {
+ struct device *dev;
+
+ /* The ioremapped HSTA MSI IO space */
+ u32 __iomem *data;
+
+ /* Physical address of HSTA MSI IO space */
+ u64 address;
+ struct msi_bitmap bmp;
+
+ /* An array mapping offsets to hardware IRQs */
+ int *irq_map;
+
+ /* Number of hwirqs supported */
+ int irq_count;
+};
+static struct ppc4xx_hsta_msi ppc4xx_hsta_msi;
+
+static int hsta_setup_msi_irqs(struct pci_dev *dev, int nvec, int type)
+{
+ struct msi_msg msg;
+ struct msi_desc *entry;
+ int irq, hwirq;
+ u64 addr;
+
+ list_for_each_entry(entry, &dev->msi_list, list) {
+ irq = msi_bitmap_alloc_hwirqs(&ppc4xx_hsta_msi.bmp, 1);
+ if (irq < 0) {
+ pr_debug("%s: Failed to allocate msi interrupt\n",
+ __func__);
+ return irq;
+ }
+
+ hwirq = ppc4xx_hsta_msi.irq_map[irq];
+ if (hwirq == NO_IRQ) {
+ pr_err("%s: Failed mapping irq %d\n", __func__, irq);
+ return -EINVAL;
+ }
+
+ /*
+ * HSTA generates interrupts on writes to 128-bit aligned
+ * addresses.
+ */
+ addr = ppc4xx_hsta_msi.address + irq*0x10;
+ msg.address_hi = upper_32_bits(addr);
+ msg.address_lo = lower_32_bits(addr);
+
+ /* Data is not used by the HSTA. */
+ msg.data = 0;
+
+ pr_debug("%s: Setup irq %d (0x%0llx)\n", __func__, hwirq,
+ (((u64) msg.address_hi) << 32) | msg.address_lo);
+
+ if (irq_set_msi_desc(hwirq, entry)) {
+ pr_err(
+ "%s: Invalid hwirq %d specified in device tree\n",
+ __func__, hwirq);
+ msi_bitmap_free_hwirqs(&ppc4xx_hsta_msi.bmp, irq, 1);
+ return -EINVAL;
+ }
+ write_msi_msg(hwirq, &msg);
+ }
+
+ return 0;
+}
+
+static int hsta_find_hwirq_offset(int hwirq)
+{
+ int irq;
+
+ /* Find the offset given the hwirq */
+ for (irq = 0; irq < ppc4xx_hsta_msi.irq_count; irq++)
+ if (ppc4xx_hsta_msi.irq_map[irq] == hwirq)
+ return irq;
+
+ return -EINVAL;
+}
+
+static void hsta_teardown_msi_irqs(struct pci_dev *dev)
+{
+ struct msi_desc *entry;
+ int irq;
+
+ list_for_each_entry(entry, &dev->msi_list, list) {
+ if (entry->irq == NO_IRQ)
+ continue;
+
+ irq = hsta_find_hwirq_offset(entry->irq);
+
+ /* entry->irq should always be in irq_map */
+ BUG_ON(irq < 0);
+ irq_set_msi_desc(entry->irq, NULL);
+ msi_bitmap_free_hwirqs(&ppc4xx_hsta_msi.bmp, irq, 1);
+ pr_debug("%s: Teardown IRQ %u (index %u)\n", __func__,
+ entry->irq, irq);
+ }
+}
+
+static int hsta_msi_check_device(struct pci_dev *pdev, int nvec, int type)
+{
+ /* We don't support MSI-X */
+ if (type == PCI_CAP_ID_MSIX) {
+ pr_debug("%s: MSI-X not supported.\n", __func__);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int hsta_msi_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct resource *mem;
+ int irq, ret, irq_count;
+
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (IS_ERR(mem)) {
+ dev_err(dev, "Unable to get mmio space\n");
+ return -EINVAL;
+ }
+
+ irq_count = of_irq_count(dev->of_node);
+ if (!irq_count) {
+ dev_err(dev, "Unable to find IRQ range\n");
+ return -EINVAL;
+ }
+
+ ppc4xx_hsta_msi.dev = dev;
+ ppc4xx_hsta_msi.address = mem->start;
+ ppc4xx_hsta_msi.data = ioremap(mem->start, resource_size(mem));
+ ppc4xx_hsta_msi.irq_count = irq_count;
+ if (IS_ERR(ppc4xx_hsta_msi.data)) {
+ dev_err(dev, "Unable to map memory\n");
+ return -ENOMEM;
+ }
+
+ ret = msi_bitmap_alloc(&ppc4xx_hsta_msi.bmp, irq_count, dev->of_node);
+ if (ret)
+ goto out;
+
+ ppc4xx_hsta_msi.irq_map = kmalloc(sizeof(int) * irq_count, GFP_KERNEL);
+ if (IS_ERR(ppc4xx_hsta_msi.irq_map)) {
+ ret = -ENOMEM;
+ goto out1;
+ }
+
+ /* Setup a mapping from irq offsets to hardware irq numbers */
+ for (irq = 0; irq < irq_count; irq++) {
+ ppc4xx_hsta_msi.irq_map[irq] =
+ irq_of_parse_and_map(dev->of_node, irq);
+ if (ppc4xx_hsta_msi.irq_map[irq] == NO_IRQ) {
+ dev_err(dev, "Unable to map IRQ\n");
+ ret = -EINVAL;
+ goto out2;
+ }
+ }
+
+ ppc_md.setup_msi_irqs = hsta_setup_msi_irqs;
+ ppc_md.teardown_msi_irqs = hsta_teardown_msi_irqs;
+ ppc_md.msi_check_device = hsta_msi_check_device;
+ return 0;
+
+out2:
+ kfree(ppc4xx_hsta_msi.irq_map);
+
+out1:
+ msi_bitmap_free(&ppc4xx_hsta_msi.bmp);
+
+out:
+ iounmap(ppc4xx_hsta_msi.data);
+ return ret;
+}
+
+static const struct of_device_id hsta_msi_ids[] = {
+ {
+ .compatible = "ibm,hsta-msi",
+ },
+ {}
+};
+
+static struct platform_driver hsta_msi_driver = {
+ .probe = hsta_msi_probe,
+ .driver = {
+ .name = "hsta-msi",
+ .owner = THIS_MODULE,
+ .of_match_table = hsta_msi_ids,
+ },
+};
+
+static int hsta_msi_init(void)
+{
+ return platform_driver_register(&hsta_msi_driver);
+}
+subsys_initcall(hsta_msi_init);
diff --git a/arch/powerpc/sysdev/ppc4xx_pci.c b/arch/powerpc/sysdev/ppc4xx_pci.c
index 54ec1d5..7cc3acc 100644
--- a/arch/powerpc/sysdev/ppc4xx_pci.c
+++ b/arch/powerpc/sysdev/ppc4xx_pci.c
@@ -176,8 +176,12 @@ static int __init ppc4xx_parse_dma_ranges(struct pci_controller *hose,
return -ENXIO;
}
- /* Check that we are fully contained within 32 bits space */
- if (res->end > 0xffffffff) {
+ /* Check that we are fully contained within 32 bits space if we are not
+ * running on a 460sx or 476fpe which have 64 bit bus addresses.
+ */
+ if (res->end > 0xffffffff &&
+ !(of_device_is_compatible(hose->dn, "ibm,plb-pciex-460sx")
+ || of_device_is_compatible(hose->dn, "ibm,plb-pciex-476fpe"))) {
printk(KERN_ERR "%s: dma-ranges outside of 32 bits space\n",
hose->dn->full_name);
return -ENXIO;
--
1.8.3.2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
