[PATCH v5 09/14] usb: phy: msm: Add device tree support and binding information

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




From: "Ivan T. Ivanov" <iivanov@xxxxxxxxxx>

Allows MSM OTG controller to be specified via device tree.

Signed-off-by: Ivan T. Ivanov <iivanov@xxxxxxxxxx>
---
 .../devicetree/bindings/usb/msm-hsusb.txt          |   67 ++++++++++++
 drivers/usb/phy/phy-msm-usb.c                      |  108 ++++++++++++++++----
 include/linux/usb/msm_hsusb.h                      |    6 +-
 3 files changed, 159 insertions(+), 22 deletions(-)

diff --git a/Documentation/devicetree/bindings/usb/msm-hsusb.txt b/Documentation/devicetree/bindings/usb/msm-hsusb.txt
index 5ea26c6..ee4123d 100644
--- a/Documentation/devicetree/bindings/usb/msm-hsusb.txt
+++ b/Documentation/devicetree/bindings/usb/msm-hsusb.txt
@@ -15,3 +15,70 @@ Example EHCI controller device node:
 		usb-phy = <&usb_otg>;
 	};

+USB PHY with optional OTG:
+
+Required properties:
+- compatible:   Should contain:
+  "qcom,usb-otg-ci" for chipsets with ChipIdea 45nm PHY
+  "qcom,usb-otg-snps" for chipsets with Synopsys 28nm PHY
+
+- regs:         Offset and length of the register set in the memory map
+- interrupts:   interrupt-specifier for the OTG interrupt.
+
+- clocks:       A list of phandle + clock-specifier pairs for the
+                clocks listed in clock-names
+- clock-names:  Should contain the following:
+  "phy"         USB PHY reference clock
+  "core"        Protocol engine clock
+  "iface"       Interface bus clock
+  "alt_core"    Protocol engine clock for targets with asynchronous
+                reset methodology. (optional)
+
+- vdccx-supply: phandle to the regulator for the vdd supply for
+                digital circuit operation.
+- v1p8-supply:  phandle to the regulator for the 1.8V supply
+- v3p3-supply:  phandle to the regulator for the 3.3V supply
+
+- resets:       A list of phandle + reset-specifier pairs for the
+                resets listed in reset-names
+- reset-names:  Should contain the following:
+  "phy"         USB PHY controller reset
+  "link"        USB LINK controller reset
+
+- qcom,otg-control: OTG control (VBUS and ID notifications) can be one of
+                1 - PHY control
+                2 - PMIC control
+
+Optional properties:
+- dr_mode:      One of "host", "peripheral" or "otg". Defaults to "otg"
+
+- qcom,phy-init-sequence: PHY configuration sequence values. This is related to Device
+                Mode Eye Diagram test. Start address at which these values will be
+                written is ULPI_EXT_VENDOR_SPECIFIC. Value of -1 is reserved as
+                "do not overwrite default value at this address".
+                For example: qcom,phy-init-sequence = < -1 0x63 >;
+                Will update only value at address ULPI_EXT_VENDOR_SPECIFIC + 1.
+
+Example HSUSB OTG controller device node:
+
+    usb@f9a55000 {
+        compatible = "qcom,usb-otg-snps";
+        reg = <0xf9a55000 0x400>;
+        interrupts = <0 134 0>;
+        dr_mode = "peripheral";
+
+        clocks = <&gcc GCC_XO_CLK>, <&gcc GCC_USB_HS_SYSTEM_CLK>,
+                <&gcc GCC_USB_HS_AHB_CLK>;
+
+        clock-names = "phy", "core", "iface";
+
+        vddcx-supply = <&pm8841_s2_corner>;
+        v1p8-supply = <&pm8941_l6>;
+        v3p3-supply = <&pm8941_l24>;
+
+        resets = <&gcc GCC_USB2A_PHY_BCR>, <&gcc GCC_USB_HS_BCR>;
+        reset-names = "phy", "link";
+
+        qcom,otg-control = <1>;
+        qcom,phy-init-sequence = < -1 0x63 >;
+	};
diff --git a/drivers/usb/phy/phy-msm-usb.c b/drivers/usb/phy/phy-msm-usb.c
index 31fb916..298820f 100644
--- a/drivers/usb/phy/phy-msm-usb.c
+++ b/drivers/usb/phy/phy-msm-usb.c
@@ -30,9 +30,12 @@
 #include <linux/debugfs.h>
 #include <linux/seq_file.h>
 #include <linux/pm_runtime.h>
+#include <linux/of.h>
+#include <linux/of_device.h>

 #include <linux/usb.h>
 #include <linux/usb/otg.h>
+#include <linux/usb/of.h>
 #include <linux/usb/ulpi.h>
 #include <linux/usb/gadget.h>
 #include <linux/usb/hcd.h>
@@ -217,16 +220,16 @@ static struct usb_phy_io_ops msm_otg_io_ops = {
 static void ulpi_init(struct msm_otg *motg)
 {
 	struct msm_otg_platform_data *pdata = motg->pdata;
-	int *seq = pdata->phy_init_seq;
+	int *seq = pdata->phy_init_seq, idx;
+	u32 addr = ULPI_EXT_VENDOR_SPECIFIC;

-	if (!seq)
-		return;
+	for (idx = 0; idx < pdata->phy_init_sz; idx++) {
+		if (seq[idx] == -1)
+			continue;

-	while (seq[0] >= 0) {
 		dev_vdbg(motg->phy.dev, "ulpi: write 0x%02x to 0x%02x\n",
-				seq[0], seq[1]);
-		ulpi_write(&motg->phy, seq[0], seq[1]);
-		seq += 2;
+				seq[idx], addr + idx);
+		ulpi_write(&motg->phy, seq[idx], addr + idx);
 	}
 }

@@ -1343,25 +1346,87 @@ static void msm_otg_debugfs_cleanup(void)
 	debugfs_remove(msm_otg_dbg_root);
 }

+static struct of_device_id msm_otg_dt_match[] = {
+	{
+		.compatible = "qcom,usb-otg-ci",
+		.data = (void *) CI_45NM_INTEGRATED_PHY
+	}, {
+		.compatible = "qcom,usb-otg-snps",
+		.data = (void *) SNPS_28NM_INTEGRATED_PHY
+	}, {}
+};
+
+static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg)
+{
+	struct msm_otg_platform_data *pdata;
+	const struct of_device_id *id;
+	struct device_node *node = pdev->dev.of_node;
+	struct property *prop;
+	int len, ret;
+	u32 val;
+
+	pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+	if (!pdata)
+		return -ENOMEM;
+
+	motg->pdata = pdata;
+
+	id = of_match_device(msm_otg_dt_match, &pdev->dev);
+	pdata->phy_type = (int) id->data;
+
+	pdata->mode = of_usb_get_dr_mode(node);
+	if (pdata->mode == USB_DR_MODE_UNKNOWN)
+		pdata->mode = USB_DR_MODE_OTG;
+
+	pdata->otg_control = OTG_PHY_CONTROL;
+	if (!of_property_read_u32(node, "qcom,otg-control", &val))
+		if (val == OTG_PMIC_CONTROL)
+			pdata->otg_control = val;
+
+	prop = of_find_property(node, "qcom,phy-init-sequence", &len);
+	if (!prop || !len)
+		return 0;
+
+	pdata->phy_init_seq = devm_kzalloc(&pdev->dev, len, GFP_KERNEL);
+	if (!pdata->phy_init_seq)
+		return 0;
+
+	len /= sizeof(u32);
+
+	if (len >= ULPI_EXT_VENDOR_SPECIFIC) {
+		dev_warn(&pdev->dev, "Too big PHY init sequence %d\n", len);
+		return 0;
+	}
+
+	ret = of_property_read_u32_array(node, "qcom,phy-init-sequence",
+					 pdata->phy_init_seq, len);
+	if (!ret)
+		pdata->phy_init_sz = len;
+	return 0;
+}
+
 static int __init msm_otg_probe(struct platform_device *pdev)
 {
 	int ret = 0;
+	struct device_node *np = pdev->dev.of_node;
+	struct msm_otg_platform_data *pdata;
 	struct resource *res;
 	struct msm_otg *motg;
 	struct usb_phy *phy;

-	dev_info(&pdev->dev, "msm_otg probe\n");
-	if (!dev_get_platdata(&pdev->dev)) {
-		dev_err(&pdev->dev, "No platform data given. Bailing out\n");
-		return -ENODEV;
-	}
-
 	motg = devm_kzalloc(&pdev->dev, sizeof(struct msm_otg), GFP_KERNEL);
 	if (!motg) {
 		dev_err(&pdev->dev, "unable to allocate msm_otg\n");
 		return -ENOMEM;
 	}

+	pdata = dev_get_platdata(&pdev->dev);
+	if (!pdata) {
+		ret = msm_otg_read_dt(pdev, motg);
+		if (ret)
+			return ret;
+	}
+
 	motg->phy.otg = devm_kzalloc(&pdev->dev, sizeof(struct usb_otg),
 				     GFP_KERNEL);
 	if (!motg->phy.otg) {
@@ -1369,17 +1434,17 @@ static int __init msm_otg_probe(struct platform_device *pdev)
 		return -ENOMEM;
 	}

-	motg->pdata = dev_get_platdata(&pdev->dev);
 	phy = &motg->phy;
 	phy->dev = &pdev->dev;

-	motg->phy_reset_clk = devm_clk_get(&pdev->dev, "usb_phy_clk");
+	motg->phy_reset_clk = devm_clk_get(&pdev->dev,
+					   np ? "phy" : "usb_phy_clk");
 	if (IS_ERR(motg->phy_reset_clk)) {
 		dev_err(&pdev->dev, "failed to get usb_phy_clk\n");
 		return PTR_ERR(motg->phy_reset_clk);
 	}

-	motg->clk = devm_clk_get(&pdev->dev, "usb_hs_clk");
+	motg->clk = devm_clk_get(&pdev->dev, np ? "core" : "usb_hs_clk");
 	if (IS_ERR(motg->clk)) {
 		dev_err(&pdev->dev, "failed to get usb_hs_clk\n");
 		return PTR_ERR(motg->clk);
@@ -1391,7 +1456,7 @@ static int __init msm_otg_probe(struct platform_device *pdev)
 	 * operation and USB core cannot tolerate frequency changes on
 	 * CORE CLK.
 	 */
-	motg->pclk = devm_clk_get(&pdev->dev, "usb_hs_pclk");
+	motg->pclk = devm_clk_get(&pdev->dev, np ? "iface" : "usb_hs_pclk");
 	if (IS_ERR(motg->pclk)) {
 		dev_err(&pdev->dev, "failed to get usb_hs_pclk\n");
 		return PTR_ERR(motg->pclk);
@@ -1402,7 +1467,8 @@ static int __init msm_otg_probe(struct platform_device *pdev)
 	 * clock is introduced to remove the dependency on AXI
 	 * bus frequency.
 	 */
-	motg->core_clk = devm_clk_get(&pdev->dev, "usb_hs_core_clk");
+	motg->core_clk = devm_clk_get(&pdev->dev,
+				      np ? "alt_core" : "usb_hs_core_clk");

 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	motg->regs = devm_ioremap(&pdev->dev, res->start, resource_size(res));
@@ -1490,8 +1556,7 @@ static int __init msm_otg_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, motg);
 	device_init_wakeup(&pdev->dev, 1);

-	if (motg->pdata->mode == USB_DR_MODE_OTG &&
-			motg->pdata->otg_control == OTG_USER_CONTROL) {
+	if (motg->pdata->mode == USB_DR_MODE_OTG) {
 		ret = msm_otg_debugfs_init(motg);
 		if (ret)
 			dev_dbg(&pdev->dev, "Can not create mode change file\n");
@@ -1637,6 +1702,8 @@ static const struct dev_pm_ops msm_otg_dev_pm_ops = {
 				msm_otg_runtime_idle)
 };

+MODULE_DEVICE_TABLE(of, msm_otg_dt_match);
+
 static struct platform_driver msm_otg_driver = {
 	.probe = msm_otg_probe,
 	.remove = msm_otg_remove,
@@ -1644,6 +1711,7 @@ static struct platform_driver msm_otg_driver = {
 		.name = DRIVER_NAME,
 		.owner = THIS_MODULE,
 		.pm = &msm_otg_dev_pm_ops,
+		.of_match_table = msm_otg_dt_match,
 	},
 };

diff --git a/include/linux/usb/msm_hsusb.h b/include/linux/usb/msm_hsusb.h
index 262ed80..bd68299 100644
--- a/include/linux/usb/msm_hsusb.h
+++ b/include/linux/usb/msm_hsusb.h
@@ -100,8 +100,9 @@ enum usb_chg_type {
 /**
  * struct msm_otg_platform_data - platform device data
  *              for msm_otg driver.
- * @phy_init_seq: PHY configuration sequence. val, reg pairs
- *              terminated by -1.
+ * @phy_init_seq: PHY configuration sequence values. Value of -1 is reserved as
+ *              "do not overwrite default vaule at this address".
+ * @phy_init_sz: PHY configuration sequence size.
  * @vbus_power: VBUS power on/off routine.
  * @power_budget: VBUS power budget in mA (0 will be treated as 500mA).
  * @mode: Supported mode (OTG/peripheral/host).
@@ -109,6 +110,7 @@ enum usb_chg_type {
  */
 struct msm_otg_platform_data {
 	int *phy_init_seq;
+	int phy_init_sz;
 	void (*vbus_power)(bool on);
 	unsigned power_budget;
 	enum usb_dr_mode mode;
--
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux