Hi Fabrizio,
On Thu, Aug 23, 2018 at 3:08 PM Fabrizio Castro
<fabrizio.castro@xxxxxxxxxxxxxx> wrote:>
> Document RZ/G2M (r8a774a1) SoC specific bindings and RZ/G2
> generic bindings.
>
> Signed-off-by: Fabrizio Castro <fabrizio.castro@xxxxxxxxxxxxxx>
> Signed-off-by: Chris Paterson <Chris.Paterson2@xxxxxxxxxxx>
> Reviewed-by: Biju Das <biju.das@xxxxxxxxxxxxxx>
Thanks for your patch!
> --- a/Documentation/devicetree/bindings/net/can/rcar_can.txt
> +++ b/Documentation/devicetree/bindings/net/can/rcar_can.txt
> @@ -4,6 +4,7 @@ Renesas R-Car CAN controller Device Tree Bindings
> Required properties:
> - compatible: "renesas,can-r8a7743" if CAN controller is a part of R8A7743 SoC.
> "renesas,can-r8a7745" if CAN controller is a part of R8A7745 SoC.
> + "renesas,can-r8a774a1" if CAN controller is a part of R8A774A1 SoC.
Looks good to me.
> "renesas,can-r8a7778" if CAN controller is a part of R8A7778 SoC.
> "renesas,can-r8a7779" if CAN controller is a part of R8A7779 SoC.
> "renesas,can-r8a7790" if CAN controller is a part of R8A7790 SoC.
> @@ -17,6 +18,7 @@ Required properties:
> "renesas,rcar-gen2-can" for a generic R-Car Gen2 or RZ/G1
> compatible device.
> "renesas,rcar-gen3-can" for a generic R-Car Gen3 compatible device.
> + "renesas,rzg-gen2-can" for a generic RZ/G2 compatible device.
AFAIK, the actual CAN module in RZ/G2M is fully compatible with the CAN
module in R-Car Gen3 SoCs. The lack of clkp2 is merely an integration
difference: as RZ/G2 SoCs do not have the CANFD module, and their CPG block
doesn't provide the CANFD clock (so the CAN device node in DT cannot refer
to that clock anyway).
Hence I don't think there's a need to introduce a "renesas,rzg-gen2-can"
compatible value.
> When compatible with the generic version, nodes must list the
> SoC-specific version corresponding to the platform first
> followed by the generic version.
> @@ -24,7 +26,9 @@ Required properties:
> - reg: physical base address and size of the R-Car CAN register map.
> - interrupts: interrupt specifier for the sole interrupt.
> - clocks: phandles and clock specifiers for 3 CAN clock inputs.
You still have "3" here. Perhaps
"Must contain a phandle and clock-specifier pair for each entry in
clock-names."?
> -- clock-names: 3 clock input name strings: "clkp1", "clkp2", "can_clk".
> +- clock-names: 2 clock input name strings for RZ/G2: "clkp1", "can_clk".
> + 3 clock input name strings for every other SoC: "clkp1", "clkp2",
> + "can_clk".
OK.
> @@ -41,8 +45,9 @@ using the below properties:
> Optional properties:
> - renesas,can-clock-select: R-Car CAN Clock Source Select. Valid values are:
> <0x0> (default) : Peripheral clock (clkp1)
> - <0x1> : Peripheral clock (clkp2)
> - <0x3> : Externally input clock
> + <0x1> : Peripheral clock (clkp2) (not supported by
> + RZ/G2 devices)
> + <0x3> : External input clock
I already expressed my feelings about this property in my reply to the first
patch ;-)
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
