Re: [PATCH v2 1/2] dt-bindings: PCI: meson: add DT bindings for Amlogic Meson PCIe controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 2018/8/24 16:22, Jerome Brunet wrote:
> On Fri, 2018-08-24 at 15:36 +0800, Hanjie Lin wrote:
>> From: Yue Wang <yue.wang@xxxxxxxxxxx>
>>
>> The Amlogic Meson PCIe host controller is based on the Synopsys DesignWare
>> PCI core. This patch adds documentation for the DT bindings in Meson PCIe
>> controller.
>>
>> Signed-off-by: Yue Wang <yue.wang@xxxxxxxxxxx>
>> Signed-off-by: Hanjie Lin <hanjie.lin@xxxxxxxxxxx>
>> ---
>>  .../devicetree/bindings/pci/amlogic,meson-pcie.txt | 63 ++++++++++++++++++++++
>>  1 file changed, 63 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
>>
>> diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
>> new file mode 100644
>> index 0000000..8a831d1
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
>> @@ -0,0 +1,63 @@
>> +Amlogic Meson AXG DWC PCIE SoC controller
>> +
>> +Amlogic Meson PCIe host controller is based on the Synopsys DesignWare PCI core.
>> +It shares common functions with the PCIe DesignWare core driver and
>> +inherits common properties defined in
>> +Documentation/devicetree/bindings/pci/designware-pci.txt.
>> +
>> +Additional properties are described here:
>> +
>> +Required properties:
>> +- compatible:
>> +	should contain "amlogic,axg-pcie" to identify the core.
>> +- reg:
>> +	Should contain the configuration address space.
>> +- reg-names: Must be
>> +	- "elbi"	External local bus interface registers
>> +	- "cfg"		Meson specific registers
>> +	- "config"	PCIe configuration space
>> +- reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal.
>> +- clocks: Must contain an entry for each entry in clock-names.
>> +- clock-names: Must include the following entries:
>> +	- "pclk"       PCIe GEN 100M PLL clock
>> +	- "port"       PCIe_x(A or B) RC clock gate
>> +	- "general"    PCIe Phy clock
>> +	- "mipi"       PCIe_x(A or B) 100M ref clock gate
>> +- resets: phandle to the reset lines.
>> +- reset-names: must contain "phy" and "peripheral"
>> +       - "port" Port A or B reset
>> +       - "apb" APB reset
> 
> The above description is not coherent (phy <=> port)
> 

Yes, this should be port and apb here.
We'll integrate phy driver into ctrl driver, and move phy reset to here also.

>> +
>> +Example configuration:
>> +
>> +	pcie: pcie@f9800000 {
>> +			compatible = "amlogic,axg-pcie", "snps,dw-pcie";
>> +			reg = <0x0 0xf9800000 0x0 0x400000
>> +					0x0 0xff646000 0x0 0x2000
>> +					0x0 0xf9f00000 0x0 0x100000>;
>> +			reg-names = "elbi", "cfg", "config";
>> +			reset-gpios = <&gpio GPIOX_19 GPIO_ACTIVE_HIGH>;
>> +			interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>;
>> +			#interrupt-cells = <1>;
>> +			interrupt-map-mask = <0 0 0 0>;
>> +			interrupt-map = <0 0 0 0 &gic GIC_SPI 179 IRQ_TYPE_EDGE_RISING>;
>> +			bus-range = <0x0 0xff>;
>> +			#address-cells = <3>;
>> +			#size-cells = <2>;
>> +			device_type = "pci";
> 
> Not described above - is it even used ?
> 

It's necessary, specified in designware-pcie.txt:
 - device_type:
  Usage: required
  Value type: <string>
  Definition: Should be "pci". 

>> +			phys = <&pcie_phy>;
> 
> Not documented and not necessary. Please remove this.
> 

We'll remove phy driver and this also.

>> +			ranges = <0x82000000 0 0 0x0 0xf9c00000 0 0x00300000>;
>> +
>> +			clocks = <&clkc CLKID_USB
>> +					&clkc CLKID_MIPI_ENABLE
>> +					&clkc CLKID_PCIE_A
>> +					&clkc CLKID_PCIE_CML_EN0>;
>> +			clock-names = "general",
>> +					"mipi",
>> +					"pclk",
>> +					"port";
>> +			resets = <&reset RESET_PCIE_A>,
>> +				<&reset RESET_PCIE_APB>;
>> +			reset-names = "port",
>> +					"apb";
>> +	};
> 
> 
> .
> 



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux