On Tue, Aug 07, 2018 at 08:59:44AM +0200, Mylène Josserand wrote:
> Hello Dmitry,
>
> Thank you again for the review.
>
> On Wed, 25 Jul 2018 17:47:32 -0700
> Dmitry Torokhov <dmitry.torokhov@xxxxxxxxx> wrote:
>
> > Hi Mylène,
> >
> > On Wed, Jul 25, 2018 at 09:34:08AM +0200, Mylène Josserand wrote:
> > > Add the support of regulator to use it as VCC source.
> > >
> > > Signed-off-by: Mylène Josserand <mylene.josserand@xxxxxxxxxxx>
> > > Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
> > > ---
> > > .../bindings/input/touchscreen/edt-ft5x06.txt | 1 +
> > > drivers/input/touchscreen/edt-ft5x06.c | 43 ++++++++++++++++++++++
> > > 2 files changed, 44 insertions(+)
> > >
> > > diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > > index 025cf8c9324a..48e975b9c1aa 100644
> > > --- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > > +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > > @@ -30,6 +30,7 @@ Required properties:
> > > Optional properties:
> > > - reset-gpios: GPIO specification for the RESET input
> > > - wake-gpios: GPIO specification for the WAKE input
> > > + - vcc-supply: Regulator that supplies the touchscreen
> > >
> > > - pinctrl-names: should be "default"
> > > - pinctrl-0: a phandle pointing to the pin settings for the
> > > diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
> > > index 1e18ca0d1b4e..dcde719094f7 100644
> > > --- a/drivers/input/touchscreen/edt-ft5x06.c
> > > +++ b/drivers/input/touchscreen/edt-ft5x06.c
> > > @@ -39,6 +39,7 @@
> > > #include <linux/input/mt.h>
> > > #include <linux/input/touchscreen.h>
> > > #include <linux/of_device.h>
> > > +#include <linux/regulator/consumer.h>
> > >
> > > #define WORK_REGISTER_THRESHOLD 0x00
> > > #define WORK_REGISTER_REPORT_RATE 0x08
> > > @@ -91,6 +92,7 @@ struct edt_ft5x06_ts_data {
> > > struct touchscreen_properties prop;
> > > u16 num_x;
> > > u16 num_y;
> > > + struct regulator *vcc;
> > >
> > > struct gpio_desc *reset_gpio;
> > > struct gpio_desc *wake_gpio;
> > > @@ -963,6 +965,13 @@ edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data *tsdata)
> > > }
> > > }
> > >
> > > +static void edt_ft5x06_disable_regulator(void *arg)
> > > +{
> > > + struct edt_ft5x06_ts_data *data = arg;
> > > +
> > > + regulator_disable(data->vcc);
> > > +}
> > > +
> > > static int edt_ft5x06_ts_probe(struct i2c_client *client,
> > > const struct i2c_device_id *id)
> > > {
> > > @@ -991,6 +1000,28 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
> > >
> > > tsdata->max_support_points = chip_data->max_support_points;
> > >
> > > + tsdata->vcc = devm_regulator_get(&client->dev, "vcc");
> > > + if (IS_ERR(tsdata->vcc)) {
> > > + error = PTR_ERR(tsdata->vcc);
> > > + if (error != -EPROBE_DEFER)
> > > + dev_err(&client->dev, "failed to request regulator: %d\n",
> > > + error);
> > > + return error;
> > > + }
> > > +
> > > + error = regulator_enable(tsdata->vcc);
> > > + if (error < 0) {
> > > + dev_err(&client->dev, "failed to enable vcc: %d\n",
> > > + error);
> > > + return error;
> > > + }
> >
> > It is better to put the chip into reset and then power up the regulatori
> > and take it out of the reset, rather than power up and then toggle reset
> > on and off.
>
> okay, thanks, I will update it.
>
> >
> > > +
> > > + error = devm_add_action_or_reset(&client->dev,
> > > + edt_ft5x06_disable_regulator,
> > > + tsdata);
> > > + if (error)
> > > + return error;
> > > +
> > > tsdata->reset_gpio = devm_gpiod_get_optional(&client->dev,
> > > "reset", GPIOD_OUT_HIGH);
> > > if (IS_ERR(tsdata->reset_gpio)) {
> > > @@ -1120,9 +1151,12 @@ static int edt_ft5x06_ts_remove(struct i2c_client *client)
> > > static int __maybe_unused edt_ft5x06_ts_suspend(struct device *dev)
> > > {
> > > struct i2c_client *client = to_i2c_client(dev);
> > > + struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
> > >
> > > if (device_may_wakeup(dev))
> > > enable_irq_wake(client->irq);
> > > + else
> > > + regulator_disable(tsdata->vcc);
> > >
> > > return 0;
> > > }
> > > @@ -1130,9 +1164,18 @@ static int __maybe_unused edt_ft5x06_ts_suspend(struct device *dev)
> > > static int __maybe_unused edt_ft5x06_ts_resume(struct device *dev)
> > > {
> > > struct i2c_client *client = to_i2c_client(dev);
> > > + struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
> > > + int ret;
> > >
> > > if (device_may_wakeup(dev))
> > > disable_irq_wake(client->irq);
> > > + else {
> > > + ret = regulator_enable(tsdata->vcc);
> > > + if (ret < 0) {
> > > + dev_err(dev, "failed to enable vcc: %d\n", ret);
> > > + return ret;
> > > + }
> > > + }
> >
> > I believe I mentioned in other review that once you powered up the
> > device, you need to restore its settings, include switching to factory
> > mode, if it was in factory mode, and restoring threshold/gain/offset
> > settings.
>
> Yes, I will update the driver with that but as I told you in a previous
> mail, I can't test the suspend/resume :(
I wonder if Simon or Lothar or Franklin could help us with it (CCed). If
not, then we'll have to go by review only.
Thanks.
--
Dmitry
