RE: [PATCH] arm64: dts: renesas: Initial r8a774a1 SoC device tree

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello Fab,

> > Subject: RE: [PATCH] arm64: dts: renesas: Initial r8a774a1 SoC device
> > tree
> >
> > Hello Fabrizio,
> >
> > > Hello Biju,
> > >
> > > Thank you for your patch.
> > >
> > > > -----Original Message-----
> > > > From: Biju Das <biju.das@xxxxxxxxxxxxxx>
> > > > Sent: 13 August 2018 08:42
> > > > To: Rob Herring <robh+dt@xxxxxxxxxx>; Mark Rutland
> > > > <mark.rutland@xxxxxxx>; Catalin Marinas
> <catalin.marinas@xxxxxxx>;
> > > > Will Deacon <will.deacon@xxxxxxx>
> > > > Cc: Biju Das <biju.das@xxxxxxxxxxxxxx>; Simon Horman
> > > > <horms@xxxxxxxxxxxx>; Magnus Damm <magnus.damm@xxxxxxxxx>;
> > > > linux-renesas-soc@xxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx;
> > > > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx; Geert Uytterhoeven
> > > > <geert+renesas@xxxxxxxxx>; Chris Paterson
> > > > <Chris.Paterson2@xxxxxxxxxxx>; Fabrizio Castro
> > > > <fabrizio.castro@xxxxxxxxxxxxxx>
> > > > Subject: [PATCH] arm64: dts: renesas: Initial r8a774a1 SoC device
> > > > tree
> > > >
> > > > Basic support for the RZ/G2M SoC.
> > > >
> > > > Signed-off-by: Biju Das <biju.das@xxxxxxxxxxxxxx>
> > > > ---
> > > >  arch/arm64/boot/dts/renesas/r8a774a1.dtsi | 192
> > > > ++++++++++++++++++++++++++++++
> > > >  1 file changed, 192 insertions(+)  create mode 100644
> > > > arch/arm64/boot/dts/renesas/r8a774a1.dtsi
> > > >
> > > > diff --git a/arch/arm64/boot/dts/renesas/r8a774a1.dtsi
> > > > b/arch/arm64/boot/dts/renesas/r8a774a1.dtsi
> > > > new file mode 100644
> > > > index 0000000..f3641c0
> > > > --- /dev/null
> > > > +++ b/arch/arm64/boot/dts/renesas/r8a774a1.dtsi
> > > > @@ -0,0 +1,192 @@
> > > > +// SPDX-License-Identifier: GPL-2.0
> > > > +/*
> > > > + * Device Tree Source for the r8a774a1 SoC
> > > > + *
> > > > + * Copyright (C) 2018 Renesas Electronics Corp.
> > > > + */
> > > > +
> > > > +#include <dt-bindings/interrupt-controller/irq.h>
> > > > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > > > +#include <dt-bindings/clock/renesas-cpg-mssr.h>
> > > > +
> > > > +#define CPG_AUDIO_CLK_I10
> > >
> > > I believe there is no use case for this macro, therefore I think
> > > this device tree can live without it.
> > > With that fixed:
> >
> > This clock is SoC specific clock similar to R-Car Gen-3 H3/M3/M3N.
> > Also the same clock is mentioned in Table  8.2b List of clocks of RZ/G2M
> hardware manual. So I think it is ok.
> >
> >  If you think defining SoC specific clock is wrong in this file , we need to fix
> other boards as well.
>
> I believe that macro is used on other platforms to provide a little bit of
> abstraction when defin ing the clocks of rcar_sound, therefore it's ok for the
> other boards.

May be I am missing something here. Can you please clarify the use case of
Other boards?

> We could provide the same thing here, it's not going to hurt anybody, but at
> the moment there is no reference design for this new SoC therefore there is
> no use case for this, so maybe we could wait until we have a use case for
> this?

> >
> >
> > > > +
> > > > +/ {
> > > > +compatible = "renesas,r8a774a1";
> > > > +#address-cells = <2>;
> > > > +#size-cells = <2>;
> > > > +
> > > > +/*
> > > > + * The external audio clocks are configured as 0 Hz fixed frequency
> > > > + * clocks by default.
> > > > + * Boards that provide audio clocks should override them.
> > > > + */
> > > > +audio_clk_a: audio_clk_a {
> > > > +compatible = "fixed-clock";
> > > > +#clock-cells = <0>;
> > > > +clock-frequency = <0>;
> > > > +};
> > > > +
> > > > +audio_clk_b: audio_clk_b {
> > > > +compatible = "fixed-clock";
> > > > +#clock-cells = <0>;
> > > > +clock-frequency = <0>;
> > > > +};
> > > > +
> > > > +audio_clk_c: audio_clk_c {
> > > > +compatible = "fixed-clock";
> > > > +#clock-cells = <0>;
> > > > +clock-frequency = <0>;
> > > > +};
> > > > +
> > > > +/* External CAN clock - to be overridden by boards that provide it */
> > > > +can_clk: can {
> > > > +compatible = "fixed-clock";
> > > > +#clock-cells = <0>;
> > > > +clock-frequency = <0>;
> > > > +};
> > > > +
> > > > +cpus {
> > > > +#address-cells = <1>;
> > > > +#size-cells = <0>;
> > > > +
> > > > +a57_0: cpu@0 {
> > > > +compatible = "arm,cortex-a57", "arm,armv8";
> > > > +reg = <0x0>;
> > > > +device_type = "cpu";
> > > > +power-domains = <&sysc 0>;
> > > > +next-level-cache = <&L2_CA57>;
> > > > +enable-method = "psci";
> > > > +clocks =<&cpg CPG_CORE 0>;
> > > > +};
> > > > +
> > > > +a57_1: cpu@1 {
> > > > +compatible = "arm,cortex-a57", "arm,armv8";
> > > > +reg = <0x1>;
> > > > +device_type = "cpu";
> > > > +power-domains = <&sysc 1>;
> > > > +next-level-cache = <&L2_CA57>;
> > > > +enable-method = "psci";
> > > > +clocks =<&cpg CPG_CORE 0>;
> > > > +};
> > > > +
> > > > +L2_CA57: cache-controller-0 {
> > > > +compatible = "cache";
> > > > +power-domains = <&sysc 12>;
> > > > +cache-unified;
> > > > +cache-level = <2>;
> > > > +};
> > > > +};
> > > > +
> > > > +extal_clk: extal {
> > > > +compatible = "fixed-clock";
> > > > +#clock-cells = <0>;
> > > > +/* This value must be overridden by the board */
> > > > +clock-frequency = <0>;
> > > > +};
> > > > +
> > > > +extalr_clk: extalr {
> > > > +compatible = "fixed-clock";
> > > > +#clock-cells = <0>;
> > > > +/* This value must be overridden by the board */
> > > > +clock-frequency = <0>;
> > > > +};
> > > > +
> > > > +/* External PCIe clock - can be overridden by the board */
> > > > +pcie_bus_clk: pcie_bus {
> > > > +compatible = "fixed-clock";
> > > > +#clock-cells = <0>;
> > > > +clock-frequency = <0>;
> > > > +};
> > > > +
> > > > +pmu_a57 {
> > > > +compatible = "arm,cortex-a57-pmu";
> > > > +interrupts-extended = <&gic GIC_SPI 72
> > > IRQ_TYPE_LEVEL_HIGH>,
> > > > +      <&gic GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
> > > > +interrupt-affinity = <&a57_0>, <&a57_1>;
> > > > +};
> > > > +
> > > > +psci {
> > > > +compatible = "arm,psci-1.0", "arm,psci-0.2";
> > > > +method = "smc";
> > > > +};
> > > > +
> > > > +/* External SCIF clock - to be overridden by boards that provide it */
> > > > +scif_clk: scif {
> > > > +compatible = "fixed-clock";
> > > > +#clock-cells = <0>;
> > > > +clock-frequency = <0>;
> > > > +};
> > > > +
> > > > +soc {
> > > > +compatible = "simple-bus";
> > > > +interrupt-parent = <&gic>;
> > > > +#address-cells = <2>;
> > > > +#size-cells = <2>;
> > > > +ranges;
> > > > +
> > > > +cpg: clock-controller@e6150000 {
> > > > +compatible = "renesas,r8a774a1-cpg-mssr";
> > > > +reg = <0 0xe6150000 0 0x0bb0>;
> > > > +clocks = <&extal_clk>, <&extalr_clk>;
> > > > +clock-names = "extal", "extalr";
> > > > +#clock-cells = <2>;
> > > > +#power-domain-cells = <0>;
> > > > +#reset-cells = <1>;
> > > > +};
> > > > +
> > > > +rst: reset-controller@e6160000 {
> > > > +compatible = "renesas,r8a774a1-rst";
> > > > +reg = <0 0xe6160000 0 0x018c>;
> > > > +};
> > > > +
> > > > +sysc: system-controller@e6180000 {
> > > > +compatible = "renesas,r8a774a1-sysc";
> > > > +reg = <0 0xe6180000 0 0x0400>;
> > > > +#power-domain-cells = <1>;
> > > > +};
> > > > +
> > > > +gic: interrupt-controller@f1010000 {
> > > > +compatible = "arm,gic-400";
> > > > +#interrupt-cells = <3>;
> > > > +#address-cells = <0>;
> > > > +interrupt-controller;
> > > > +reg = <0x0 0xf1010000 0 0x1000>,
> > > > +      <0x0 0xf1020000 0 0x20000>,
> > > > +      <0x0 0xf1040000 0 0x20000>,
> > > > +      <0x0 0xf1060000 0 0x20000>;
> > > > +interrupts = <GIC_PPI 9
> > > > +(GIC_CPU_MASK_SIMPLE(2) |
> > > IRQ_TYPE_LEVEL_HIGH)>;
> > > > +clocks = <&cpg CPG_MOD 408>;
> > > > +clock-names = "clk";
> > > > +power-domains = <&sysc 32>;
> > > > +resets = <&cpg 408>;
> > > > +};
> > > > +
> > > > +prr: chipid@fff00044 {
> > > > +compatible = "renesas,prr";
> > > > +reg = <0 0xfff00044 0 4>;
> > > > +};
> > > > +};
> > > > +
> > > > +timer {
> > > > +compatible = "arm,armv8-timer";
> > > > +interrupts-extended = <&gic GIC_PPI 13
> > > (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
> > > > +      <&gic GIC_PPI 14
> > > (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
> > > > +      <&gic GIC_PPI 11
> > > (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
> > > > +      <&gic GIC_PPI 10
> > > (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
> > > > +};
> > > > +
> > > > +/* External USB clocks - can be overridden by the board */
> > > > +usb3s0_clk: usb3s0 {
> > > > +compatible = "fixed-clock";
> > > > +#clock-cells = <0>;
> > > > +clock-frequency = <0>;
> > > > +};
> > > > +
> > > > +usb_extal_clk: usb_extal {
> > > > +compatible = "fixed-clock";
> > > > +#clock-cells = <0>;
> > > > +clock-frequency = <0>;
> > > > +};
> > > > +};
> > > > --
> > > > 2.7.4




Renesas Electronics Europe Ltd, Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, UK. Registered in England & Wales under Registered No. 04586709.




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux