Re: [PATCH] ARM: dts: add BeagleBone Audio Cape (Rev A) dtsi

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 28/02/2014 23:17, Tony Lindgren wrote:
* Jack Mitchell <ml@xxxxxxxxxxx> [140122 03:09]:
From: Jack Mitchell <jack@xxxxxxxxxxx>

Devicetree include file for setting up the am335x mcasp bus, i2c-2
bus, and audio codec required for a functioning BeagleBone Audio Cape.

Signed-off-by: Jack Mitchell <jack@xxxxxxxxxxx>
Signed-off-by: Matt Porter <mporter@xxxxxxxxxx>
---
  arch/arm/boot/dts/am335x-bone-audio-cape-reva.dtsi | 124 +++++++++++++++++++++
  arch/arm/boot/dts/am335x-bone-common.dtsi          |  14 +++
  2 files changed, 138 insertions(+)
  create mode 100644 arch/arm/boot/dts/am335x-bone-audio-cape-reva.dtsi

diff --git a/arch/arm/boot/dts/am335x-bone-audio-cape-reva.dtsi b/arch/arm/boot/dts/am335x-bone-audio-cape-reva.dtsi
new file mode 100644
index 0000000..b8ec3dc
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-bone-audio-cape-reva.dtsi
@@ -0,0 +1,124 @@
+/*
+ * Copyright (C) 2014 Jack Mitchell <jack@xxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * In order to enable the BeagleBone Audio Cape this dtsi must be
+ * incuded in the top level dts. On BeagleBone Black hardware the
+ * status of the HDMI dts node must also be set to "disabled".

Seems like this is unsafe to merge then? This probably also needs
comments from Peter Ujfalusi, added him to Cc.

Maybe, we'd better define a new DTS board (like am335x-boneblack-audio.dts) if we cannot use audio cape without losing the HDMI. Since we don't have mechanism like overlay, we don't have the choice but defining several boards for each cape variant.

BTW, what is the conflict source with HDMI?
At some point I remember that the mcasp for audio cape was broken because of changes in the mcasp for the HDMI, but it is not the case anymore, thanks to the cleanup from Jyri.


+ * --- a/arch/arm/boot/dts/am335x-bone.dts
+ * +++ b/arch/arm/boot/dts/am335x-bone.dts
+ * @@ -9,6 +9,7 @@
+ *
+ *  #include "am33xx.dtsi"
+ *  #include "am335x-bone-common.dtsi"
+ * +#include "am335x-bone-audio-cape-reva.dtsi"
+ *
+ *  &ldo3_reg {
+ *  	regulator-min-microvolt = <1800000>;
+ *
+ * On BeagleBone Black hardware the status of the HDMI dts node must
+ * also be set to "disabled"
+ *
+ * --- a/arch/arm/boot/dts/am335x-boneblack.dts
+ * +++ b/arch/arm/boot/dts/am335x-boneblack.dts
+ * @@ -73,6 +74,6 @@
+ *  		pinctrl-names = "default", "off";
+ *  		pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
+ *  		pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
+ * -		status = "okay";
+ * +		status = "disabled";
+ *  	};
+ *  };
+ */
+
+/ {
+	sound {
+		compatible = "ti,da830-evm-audio";
+		ti,model = "AM335x BeagleBone Audio Cape Rev. A";
+		ti,audio-codec = <&tlv320aic3106>;
+		ti,mcasp-controller = <&mcasp0>;
+		ti,codec-clock-rate = <12000000>;
+		ti,audio-routing =
+			"Headphone Jack",       "HPLOUT",
+			"Headphone Jack",       "HPROUT",
+			"LINE1L",               "Line In",
+			"LINE1R",               "Line In";
+	};
+
+	audio-cape-gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bone_audio_cape_led_pins>;
+
+		audio-led0 {
+			label = "audio:green:usr0";
+			gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		audio-led1 {
+			label = "audio:green:usr1";
+			gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+	};
+};
+
+&am33xx_pinmux {
+	bone_audio_cape_led_pins: pinmux_bone_audio_cape_led_pins {
+		pinctrl-single,pins = <
+			0x48 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a2.gpio1_18 */
+			0x4c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a3.gpio1_19 */
+		>;
+	};
+
+	bone_audio_cape_pins: bone_audio_cape_pins {
+		pinctrl-single,pins = <
+			0x190 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mcasp0_aclkx.mcasp0_aclkx */
+			0x194 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mcasp0_fsx.mcasp0_fsx */
+			0x19c (PIN_INPUT_PULLUP | MUX_MODE2)	/* mcasp0_ahclkr.mcasp0_axr2 */
+			0x1ac (PIN_INPUT_PULLUP | MUX_MODE2)	/* mcasp0_ahclkx.mcasp0_axr3 */
+		>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+
+	status = "okay";
+	clock-frequency = <100000>;
+
+	tlv320aic3106: tlv320aic3106@1b {

A more generic name will be prefered here.

Regards,
Benoit

--
Benoît Cousson
BayLibre
Embedded Linux Technology Lab
www.baylibre.com
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux