Modify the register offsets in the Broadcom iProc mdio mux to start
from the top of the register address space.
Earlier, the base address pointed to the end of the block's register
space. The base address will now point to the start of the mdio's
address space. The offsets have been fixed to match this.
Signed-off-by: Arun Parameswaran <arun.parameswaran@xxxxxxxxxxxx>
Reviewed-by: Andrew Lunn <andrew@xxxxxxx>
Reviewed-by: Florian Fainelli <f.fainelli@xxxxxxxxx>
---
drivers/net/phy/mdio-mux-bcm-iproc.c | 20 +++++++++++++++-----
1 file changed, 15 insertions(+), 5 deletions(-)
diff --git a/drivers/net/phy/mdio-mux-bcm-iproc.c b/drivers/net/phy/mdio-mux-bcm-iproc.c
index 0831b71..48bb74a 100644
--- a/drivers/net/phy/mdio-mux-bcm-iproc.c
+++ b/drivers/net/phy/mdio-mux-bcm-iproc.c
@@ -22,7 +22,7 @@
#include <linux/mdio-mux.h>
#include <linux/delay.h>
-#define MDIO_PARAM_OFFSET 0x00
+#define MDIO_PARAM_OFFSET 0x23c
#define MDIO_PARAM_MIIM_CYCLE 29
#define MDIO_PARAM_INTERNAL_SEL 25
#define MDIO_PARAM_BUS_ID 22
@@ -30,20 +30,22 @@
#define MDIO_PARAM_PHY_ID 16
#define MDIO_PARAM_PHY_DATA 0
-#define MDIO_READ_OFFSET 0x04
+#define MDIO_READ_OFFSET 0x240
#define MDIO_READ_DATA_MASK 0xffff
-#define MDIO_ADDR_OFFSET 0x08
+#define MDIO_ADDR_OFFSET 0x244
-#define MDIO_CTRL_OFFSET 0x0C
+#define MDIO_CTRL_OFFSET 0x248
#define MDIO_CTRL_WRITE_OP 0x1
#define MDIO_CTRL_READ_OP 0x2
-#define MDIO_STAT_OFFSET 0x10
+#define MDIO_STAT_OFFSET 0x24c
#define MDIO_STAT_DONE 1
#define BUS_MAX_ADDR 32
#define EXT_BUS_START_ADDR 16
+#define MDIO_REG_ADDR_SPACE_SIZE 0x250
+
struct iproc_mdiomux_desc {
void *mux_handle;
void __iomem *base;
@@ -169,6 +171,14 @@ static int mdio_mux_iproc_probe(struct platform_device *pdev)
md->dev = &pdev->dev;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (res->start & 0xfff) {
+ /* For backward compatibility in case the
+ * base address is specified with an offset.
+ */
+ dev_info(&pdev->dev, "fix base address in dt-blob\n");
+ res->start &= ~0xfff;
+ res->end = res->start + MDIO_REG_ADDR_SPACE_SIZE - 1;
+ }
md->base = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(md->base)) {
dev_err(&pdev->dev, "failed to ioremap register\n");
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
