On Mon, Mar 3, 2014 at 10:01 AM, Jason Gunthorpe
<jgunthorpe@xxxxxxxxxxxxxxxxxxxx> wrote:
> On Mon, Mar 03, 2014 at 09:49:52AM -0800, Tim Harvey wrote:
>
>> I'm not clear why irq 20 is getting returned for all the slots with
>> (slot%4)=0 and func=0. If I start debugging of_irq_parse_pci() I see
>> that it walks up the tree until it gets to the pcie host controller
>> then calls of_irq_parse_raw() which is returning irq20 or -EINVAL.
>
> Can you share your DT as well?
sure - I'm not sure what the best way to show this is (a dtc
commandline probably?). This is from u-boot:
/ {
board = "GW5410-SP275-B";
system-serial = [35 30 38 38 30];
#address-cells = <0x00000001>;
#size-cells = <0x00000001>;
model = "Gateworks Ventana i.MX6 Quad GW54XX";
compatible = "gw,imx6q-gw54xx", "gw,ventana", "fsl,imx6q";
chosen {
bootargs = "console=ttymxc1,115200";
};
aliases {
gpio0 = "/soc/aips-bus@02000000/gpio@0209c000";
gpio1 = "/soc/aips-bus@02000000/gpio@020a0000";
gpio2 = "/soc/aips-bus@02000000/gpio@020a4000";
gpio3 = "/soc/aips-bus@02000000/gpio@020a8000";
gpio4 = "/soc/aips-bus@02000000/gpio@020ac000";
gpio5 = "/soc/aips-bus@02000000/gpio@020b0000";
gpio6 = "/soc/aips-bus@02000000/gpio@020b4000";
i2c0 = "/soc/aips-bus@02100000/i2c@021a0000";
i2c1 = "/soc/aips-bus@02100000/i2c@021a4000";
i2c2 = "/soc/aips-bus@02100000/i2c@021a8000";
serial0 =
"/soc/aips-bus@02000000/spba-bus@02000000/serial@02020000";
serial1 = "/soc/aips-bus@02100000/serial@021e8000";
serial4 = "/soc/aips-bus@02100000/serial@021f4000";
can0 = "/soc/aips-bus@02000000/flexcan@02090000";
ethernet0 = "/soc/aips-bus@02100000/ethernet@02188000";
led0 = "/leds/user1";
led1 = "/leds/user2";
led2 = "/leds/user3";
nand = "/soc/gpmi-nand@00112000";
usb0 = "/soc/aips-bus@02100000/usb@02184200";
usb1 = "/soc/aips-bus@02100000/usb@02184000";
usdhc2 = "/soc/aips-bus@02100000/usdhc@02198000";
};
memory {
device_type = "memory";
reg = <0x10000000 0x40000000>;
};
interrupt-controller@00a01000 {
compatible = "arm,cortex-a9-gic";
#interrupt-cells = <0x00000003>;
#address-cells = <0x00000001>;
#size-cells = <0x00000001>;
interrupt-controller;
reg = <0x00a01000 0x00001000 0x00a00100 0x00000100>;
linux,phandle = <0x00000001>;
phandle = <0x00000001>;
};
clocks {
#address-cells = <0x00000001>;
#size-cells = <0x00000000>;
ckil {
compatible = "fsl,imx-ckil", "fixed-clock";
clock-frequency = <0x00008000>;
};
ckih1 {
compatible = "fsl,imx-ckih1", "fixed-clock";
clock-frequency = <0x00000000>;
};
osc {
compatible = "fsl,imx-osc", "fixed-clock";
clock-frequency = <0x016e3600>;
};
};
soc {
#address-cells = <0x00000001>;
#size-cells = <0x00000001>;
compatible = "simple-bus";
interrupt-parent = <0x00000001>;
ranges;
dma-apbh@00110000 {
compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh";
reg = <0x00110000 0x00002000>;
interrupts = <0x00000000 0x0000000d 0x00000004
0x00000000 0x0000000d 0x00000004 0x00000000 0x0000000d 0x00000004
0x00000000 0x0000000d 0x00000004>;
interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
#dma-cells = <0x00000001>;
dma-channels = <0x00000004>;
clocks = <0x00000002 0x0000006a>;
linux,phandle = <0x00000003>;
phandle = <0x00000003>;
};
gpmi-nand@00112000 {
compatible = "fsl,imx6q-gpmi-nand";
#address-cells = <0x00000001>;
#size-cells = <0x00000001>;
reg = <0x00112000 0x00002000 0x00114000 0x00002000>;
reg-names = "gpmi-nand", "bch";
interrupts = <0x00000000 0x0000000f 0x00000004>;
interrupt-names = "bch";
clocks = <0x00000002 0x00000098 0x00000002
0x00000099 0x00000002 0x00000097 0x00000002 0x00000096 0x00000002
0x00000095>;
clock-names = "gpmi_io", "gpmi_apb",
"gpmi_bch", "gpmi_bch_apb", "per1_bch";
dmas = <0x00000003 0x00000000>;
dma-names = "rx-tx";
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <0x00000004>;
partition@0 {
label = "uboot";
reg = <0x00000000 0x01000000>;
};
partition@1000000 {
label = "env";
reg = <0x01000000 0x00100000>;
};
partition@1100000 {
label = "rootfs";
reg = <0x01100000 0x0ef00000>;
};
};
timer@00a00600 {
compatible = "arm,cortex-a9-twd-timer";
reg = <0x00a00600 0x00000020>;
interrupts = <0x00000001 0x0000000d 0x00000f01>;
clocks = <0x00000002 0x0000000f>;
};
l2-cache@00a02000 {
compatible = "arm,pl310-cache";
reg = <0x00a02000 0x00001000>;
interrupts = <0x00000000 0x0000005c 0x00000004>;
cache-unified;
cache-level = <0x00000002>;
arm,tag-latency = <0x00000004 0x00000002 0x00000003>;
arm,data-latency = <0x00000004 0x00000002 0x00000003>;
linux,phandle = <0x00000022>;
phandle = <0x00000022>;
};
pcie@0x01000000 {
compatible = "fsl,imx6q-pcie", "snps,dw-pcie";
reg = <0x01ffc000 0x00004000>;
#address-cells = <0x00000003>;
#size-cells = <0x00000002>;
device_type = "pci";
ranges = * 0x18000ce0 [0x00000048];
num-lanes = <0x00000001>;
interrupts = <0x00000000 0x0000007b 0x00000004>;
#interrupt-cells = <0x00000001>;
interrupt-map-mask = <0x00000000 0x00000000
0x00000000 0x00000007>;
interrupt-map = * 0x18000d88 [0x00000080];
clocks = <0x00000002 0x000000bd 0x00000002
0x000000bb 0x00000002 0x000000ce 0x00000002 0x00000090>;
clock-names = "pcie_ref_125m",
"sata_ref_100m", "lvds_gate", "pcie_axi";
status = "okay";
reset-gpio = <0x00000005 0x0000001d 0x00000000>;
};
pmu {
compatible = "arm,cortex-a9-pmu";
interrupts = <0x00000000 0x0000005e 0x00000004>;
};
aips-bus@02000000 {
compatible = "fsl,aips-bus", "simple-bus";
#address-cells = <0x00000001>;
#size-cells = <0x00000001>;
reg = <0x02000000 0x00100000>;
ranges;
spba-bus@02000000 {
compatible = "fsl,spba-bus", "simple-bus";
#address-cells = <0x00000001>;
#size-cells = <0x00000001>;
reg = <0x02000000 0x00040000>;
ranges;
spdif@02004000 {
compatible = "fsl,imx35-spdif";
reg = <0x02004000 0x00004000>;
interrupts = <0x00000000
0x00000034 0x00000004>;
dmas = <0x00000006 0x0000000e
0x00000012 0x00000000 0x00000006 0x0000000f 0x00000012 0x00000000>;
dma-names = "rx", "tx";
clocks = * 0x18001084 [0x00000048];
clock-names = "core", "rxtx0",
"rxtx1", "rxtx2", "rxtx3", "rxtx4", "rxtx5", "rxtx6", "rxtx7";
status = "disabled";
};
serial@02020000 {
compatible = "fsl,imx6q-uart",
"fsl,imx21-uart";
reg = <0x02020000 0x00004000>;
interrupts = <0x00000000
0x0000001a 0x00000004>;
clocks = <0x00000002
0x000000a0 0x00000002 0x000000a1>;
clock-names = "ipg", "per";
dmas = <0x00000006 0x00000019
0x00000004 0x00000000 0x00000006 0x0000001a 0x00000004 0x00000000>;
dma-names = "rx", "tx";
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <0x00000007>;
};
esai@02024000 {
reg = <0x02024000 0x00004000>;
interrupts = <0x00000000
0x00000033 0x00000004>;
};
ssi@0202c000 {
compatible = "fsl,imx6q-ssi",
"fsl,imx21-ssi";
reg = <0x0202c000 0x00004000>;
interrupts = <0x00000000
0x0000002f 0x00000004>;
clocks = <0x00000002 0x000000b3>;
dmas = <0x00000006 0x00000029
0x00000001 0x00000000 0x00000006 0x0000002a 0x00000001 0x00000000>;
dma-names = "rx", "tx";
fsl,fifo-depth = <0x0000000f>;
fsl,ssi-dma-events =
<0x0000002a 0x00000029>;
status = "okay";
fsl,mode = "i2s-slave";
};
ssi@02030000 {
compatible = "fsl,imx6q-ssi",
"fsl,imx21-ssi";
reg = <0x02030000 0x00004000>;
interrupts = <0x00000000
0x00000030 0x00000004>;
clocks = <0x00000002 0x000000b4>;
dmas = <0x00000006 0x0000002d
0x00000001 0x00000000 0x00000006 0x0000002e 0x00000001 0x00000000>;
dma-names = "rx", "tx";
fsl,fifo-depth = <0x0000000f>;
fsl,ssi-dma-events =
<0x0000002e 0x0000002d>;
status = "disabled";
};
asrc@02034000 {
reg = <0x02034000 0x00004000>;
interrupts = <0x00000000
0x00000032 0x00000004>;
};
spba@0203c000 {
reg = <0x0203c000 0x00004000>;
};
ecspi@02018000 {
#address-cells = <0x00000001>;
#size-cells = <0x00000000>;
compatible =
"fsl,imx6q-ecspi", "fsl,imx51-ecspi";
reg = <0x02018000 0x00004000>;
interrupts = <0x00000000
0x00000023 0x00000004>;
clocks = <0x00000002
0x00000074 0x00000002 0x00000074>;
clock-names = "ipg", "per";
status = "disabled";
};
};
vpu@02040000 {
reg = <0x02040000 0x0003c000>;
interrupts = <0x00000000 0x00000003
0x00000004 0x00000000 0x0000000c 0x00000004>;
};
aipstz@0207c000 {
reg = <0x0207c000 0x00004000>;
};
pwm@02080000 {
#pwm-cells = <0x00000002>;
compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm";
reg = <0x02080000 0x00004000>;
interrupts = <0x00000000 0x00000053 0x00000004>;
clocks = <0x00000002 0x0000003e
0x00000002 0x00000091>;
clock-names = "ipg", "per";
};
pwm@02084000 {
#pwm-cells = <0x00000002>;
compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm";
reg = <0x02084000 0x00004000>;
interrupts = <0x00000000 0x00000054 0x00000004>;
clocks = <0x00000002 0x0000003e
0x00000002 0x00000092>;
clock-names = "ipg", "per";
};
pwm@02088000 {
#pwm-cells = <0x00000002>;
compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm";
reg = <0x02088000 0x00004000>;
interrupts = <0x00000000 0x00000055 0x00000004>;
clocks = <0x00000002 0x0000003e
0x00000002 0x00000093>;
clock-names = "ipg", "per";
};
pwm@0208c000 {
#pwm-cells = <0x00000002>;
compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm";
reg = <0x0208c000 0x00004000>;
interrupts = <0x00000000 0x00000056 0x00000004>;
clocks = <0x00000002 0x0000003e
0x00000002 0x00000094>;
clock-names = "ipg", "per";
};
flexcan@02090000 {
compatible = "fsl,imx6q-flexcan";
reg = <0x02090000 0x00004000>;
interrupts = <0x00000000 0x0000006e 0x00000004>;
clocks = <0x00000002 0x0000006c
0x00000002 0x0000006d>;
clock-names = "ipg", "per";
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <0x00000008>;
};
flexcan@02094000 {
compatible = "fsl,imx6q-flexcan";
reg = <0x02094000 0x00004000>;
interrupts = <0x00000000 0x0000006f 0x00000004>;
clocks = <0x00000002 0x0000006e
0x00000002 0x0000006f>;
clock-names = "ipg", "per";
status = "disabled";
};
gpt@02098000 {
compatible = "fsl,imx6q-gpt", "fsl,imx31-gpt";
reg = <0x02098000 0x00004000>;
interrupts = <0x00000000 0x00000037 0x00000004>;
clocks = <0x00000002 0x00000077
0x00000002 0x00000078>;
clock-names = "ipg", "per";
};
gpio@0209c000 {
compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio";
reg = <0x0209c000 0x00004000>;
interrupts = <0x00000000 0x00000042
0x00000004 0x00000000 0x00000043 0x00000004>;
gpio-controller;
#gpio-cells = <0x00000002>;
interrupt-controller;
#interrupt-cells = <0x00000002>;
linux,phandle = <0x00000005>;
phandle = <0x00000005>;
};
gpio@020a0000 {
compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio";
reg = <0x020a0000 0x00004000>;
interrupts = <0x00000000 0x00000044
0x00000004 0x00000000 0x00000045 0x00000004>;
gpio-controller;
#gpio-cells = <0x00000002>;
interrupt-controller;
#interrupt-cells = <0x00000002>;
};
gpio@020a4000 {
compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio";
reg = <0x020a4000 0x00004000>;
interrupts = <0x00000000 0x00000046
0x00000004 0x00000000 0x00000047 0x00000004>;
gpio-controller;
#gpio-cells = <0x00000002>;
interrupt-controller;
#interrupt-cells = <0x00000002>;
linux,phandle = <0x00000027>;
phandle = <0x00000027>;
};
gpio@020a8000 {
compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio";
reg = <0x020a8000 0x00004000>;
interrupts = <0x00000000 0x00000048
0x00000004 0x00000000 0x00000049 0x00000004>;
gpio-controller;
#gpio-cells = <0x00000002>;
interrupt-controller;
#interrupt-cells = <0x00000002>;
linux,phandle = <0x00000026>;
phandle = <0x00000026>;
};
gpio@020ac000 {
compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio";
reg = <0x020ac000 0x00004000>;
interrupts = <0x00000000 0x0000004a
0x00000004 0x00000000 0x0000004b 0x00000004>;
gpio-controller;
#gpio-cells = <0x00000002>;
interrupt-controller;
#interrupt-cells = <0x00000002>;
};
gpio@020b0000 {
compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio";
reg = <0x020b0000 0x00004000>;
interrupts = <0x00000000 0x0000004c
0x00000004 0x00000000 0x0000004d 0x00000004>;
gpio-controller;
#gpio-cells = <0x00000002>;
interrupt-controller;
#interrupt-cells = <0x00000002>;
};
gpio@020b4000 {
compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio";
reg = <0x020b4000 0x00004000>;
interrupts = <0x00000000 0x0000004e
0x00000004 0x00000000 0x0000004f 0x00000004>;
gpio-controller;
#gpio-cells = <0x00000002>;
interrupt-controller;
#interrupt-cells = <0x00000002>;
linux,phandle = <0x00000018>;
phandle = <0x00000018>;
};
kpp@020b8000 {
reg = <0x020b8000 0x00004000>;
interrupts = <0x00000000 0x00000052 0x00000004>;
};
wdog@020bc000 {
compatible = "fsl,imx6q-wdt", "fsl,imx21-wdt";
reg = <0x020bc000 0x00004000>;
interrupts = <0x00000000 0x00000050 0x00000004>;
clocks = <0x00000002 0x00000000>;
};
wdog@020c0000 {
compatible = "fsl,imx6q-wdt", "fsl,imx21-wdt";
reg = <0x020c0000 0x00004000>;
interrupts = <0x00000000 0x00000051 0x00000004>;
clocks = <0x00000002 0x00000000>;
status = "disabled";
};
ccm@020c4000 {
compatible = "fsl,imx6q-ccm";
reg = <0x020c4000 0x00004000>;
interrupts = <0x00000000 0x00000057
0x00000004 0x00000000 0x00000058 0x00000004>;
#clock-cells = <0x00000001>;
linux,phandle = <0x00000002>;
phandle = <0x00000002>;
};
anatop@020c8000 {
compatible = "fsl,imx6q-anatop",
"syscon", "simple-bus";
reg = <0x020c8000 0x00001000>;
interrupts = <0x00000000 0x00000031
0x00000004 0x00000000 0x00000036 0x00000004 0x00000000 0x0000007f
0x00000004>;
linux,phandle = <0x00000009>;
phandle = <0x00000009>;
regulator-1p1@110 {
compatible = "fsl,anatop-regulator";
regulator-name = "vdd1p1";
regulator-min-microvolt = "", "5";
regulator-max-microvolt = <0x0014fb18>;
regulator-always-on;
anatop-reg-offset = <0x00000110>;
anatop-vol-bit-shift = <0x00000008>;
anatop-vol-bit-width = <0x00000005>;
anatop-min-bit-val = <0x00000004>;
anatop-min-voltage = "", "5";
anatop-max-voltage = <0x0014fb18>;
};
regulator-3p0@120 {
compatible = "fsl,anatop-regulator";
regulator-name = "vdd3p0";
regulator-min-microvolt = <0x002ab980>;
regulator-max-microvolt = <0x003010b0>;
regulator-always-on;
anatop-reg-offset = <0x00000120>;
anatop-vol-bit-shift = <0x00000008>;
anatop-vol-bit-width = <0x00000005>;
anatop-min-bit-val = <0x00000000>;
anatop-min-voltage = <0x00280de8>;
anatop-max-voltage = <0x0033e140>;
};
regulator-2p5@130 {
compatible = "fsl,anatop-regulator";
regulator-name = "vdd2p5";
regulator-min-microvolt = <0x001e8480>;
regulator-max-microvolt = <0x0029f630>;
regulator-always-on;
anatop-reg-offset = <0x00000130>;
anatop-vol-bit-shift = <0x00000008>;
anatop-vol-bit-width = <0x00000005>;
anatop-min-bit-val = <0x00000000>;
anatop-min-voltage = <0x001e8480>;
anatop-max-voltage = <0x0029f630>;
};
regulator-vddcore@140 {
compatible = "fsl,anatop-regulator";
regulator-name = "cpu";
regulator-min-microvolt = <0x000b1008>;
regulator-max-microvolt = <0x00162010>;
regulator-always-on;
anatop-reg-offset = <0x00000140>;
anatop-vol-bit-shift = <0x00000000>;
anatop-vol-bit-width = <0x00000005>;
anatop-delay-reg-offset = <0x00000170>;
anatop-delay-bit-shift = <0x00000018>;
anatop-delay-bit-width = <0x00000002>;
anatop-min-bit-val = <0x00000001>;
anatop-min-voltage = <0x000b1008>;
anatop-max-voltage = <0x00162010>;
linux,phandle = <0x00000023>;
phandle = <0x00000023>;
};
regulator-vddpu@140 {
compatible = "fsl,anatop-regulator";
regulator-name = "vddpu";
regulator-min-microvolt = <0x000b1008>;
regulator-max-microvolt = <0x00162010>;
regulator-always-on;
anatop-reg-offset = <0x00000140>;
anatop-vol-bit-shift = <0x00000009>;
anatop-vol-bit-width = <0x00000005>;
anatop-delay-reg-offset = <0x00000170>;
anatop-delay-bit-shift = <0x0000001a>;
anatop-delay-bit-width = <0x00000002>;
anatop-min-bit-val = <0x00000001>;
anatop-min-voltage = <0x000b1008>;
anatop-max-voltage = <0x00162010>;
linux,phandle = <0x00000024>;
phandle = <0x00000024>;
};
regulator-vddsoc@140 {
compatible = "fsl,anatop-regulator";
regulator-name = "vddsoc";
regulator-min-microvolt = <0x000b1008>;
regulator-max-microvolt = <0x00162010>;
regulator-always-on;
anatop-reg-offset = <0x00000140>;
anatop-vol-bit-shift = <0x00000012>;
anatop-vol-bit-width = <0x00000005>;
anatop-delay-reg-offset = <0x00000170>;
anatop-delay-bit-shift = <0x0000001c>;
anatop-delay-bit-width = <0x00000002>;
anatop-min-bit-val = <0x00000001>;
anatop-min-voltage = <0x000b1008>;
anatop-max-voltage = <0x00162010>;
linux,phandle = <0x00000025>;
phandle = <0x00000025>;
};
};
tempmon {
compatible = "fsl,imx6q-tempmon";
interrupts = <0x00000000 0x00000031 0x00000004>;
fsl,tempmon = <0x00000009>;
fsl,tempmon-data = <0x0000000a>;
};
usbphy@020c9000 {
compatible = "fsl,imx6q-usbphy",
"fsl,imx23-usbphy";
reg = <0x020c9000 0x00001000>;
interrupts = <0x00000000 0x0000002c 0x00000004>;
clocks = <0x00000002 0x000000b6>;
linux,phandle = <0x00000010>;
phandle = <0x00000010>;
};
usbphy@020ca000 {
compatible = "fsl,imx6q-usbphy",
"fsl,imx23-usbphy";
reg = <0x020ca000 0x00001000>;
interrupts = <0x00000000 0x0000002d 0x00000004>;
clocks = <0x00000002 0x000000b7>;
linux,phandle = <0x00000014>;
phandle = <0x00000014>;
};
snvs@020cc000 {
compatible = "fsl,sec-v4.0-mon", "simple-bus";
#address-cells = <0x00000001>;
#size-cells = <0x00000001>;
ranges = <0x00000000 0x020cc000 0x00004000>;
snvs-rtc-lp@34 {
compatible = "fsl,sec-v4.0-mon-rtc-lp";
reg = <0x00000034 0x00000058>;
interrupts = <0x00000000
0x00000013 0x00000004 0x00000000 0x00000014 0x00000004>;
};
};
epit@020d0000 {
reg = <0x020d0000 0x00004000>;
interrupts = <0x00000000 0x00000038 0x00000004>;
};
epit@020d4000 {
reg = <0x020d4000 0x00004000>;
interrupts = <0x00000000 0x00000039 0x00000004>;
};
src@020d8000 {
compatible = "fsl,imx6q-src", "fsl,imx51-src";
reg = <0x020d8000 0x00004000>;
interrupts = <0x00000000 0x0000005b
0x00000004 0x00000000 0x00000060 0x00000004>;
#reset-cells = <0x00000001>;
linux,phandle = <0x00000021>;
phandle = <0x00000021>;
};
gpc@020dc000 {
compatible = "fsl,imx6q-gpc";
reg = <0x020dc000 0x00004000>;
interrupts = <0x00000000 0x00000059
0x00000004 0x00000000 0x0000005a 0x00000004>;
};
iomuxc-gpr@020e0000 {
compatible = "fsl,imx6q-iomuxc-gpr", "syscon";
reg = <0x020e0000 0x00000038>;
linux,phandle = <0x0000000c>;
phandle = <0x0000000c>;
};
iomuxc@020e0000 {
compatible = "fsl,imx6q-iomuxc";
reg = <0x020e0000 0x00004000>;
pinctrl-names = "default";
pinctrl-0 = <0x0000000b>;
audmux {
audmux-1 {
fsl,pins = *
0x18002eb8 [0x00000060];
linux,phandle = <0x0000001e>;
phandle = <0x0000001e>;
};
audmux-2 {
fsl,pins = *
0x18002f58 [0x00000060];
};
audmux-3 {
fsl,pins = *
0x18002fd8 [0x00000048];
};
audmux-4 {
fsl,pins = *
0x18003040 [0x00000048];
};
};
ecspi1 {
ecspi1grp-1 {
fsl,pins = *
0x180030b8 [0x00000048];
};
ecspi1grp-2 {
fsl,pins = *
0x18003120 [0x00000048];
};
};
ecspi3 {
ecspi3grp-1 {
fsl,pins = *
0x18003198 [0x00000048];
};
};
enet {
enetgrp-1 {
fsl,pins = *
0x18003210 [0x00000180];
linux,phandle = <0x00000016>;
phandle = <0x00000016>;
};
enetgrp-2 {
fsl,pins = *
0x180033d0 [0x00000168];
};
enetgrp-3 {
fsl,pins = *
0x18003558 [0x00000180];
};
};
esai {
esaigrp-1 {
fsl,pins = *
0x18003708 [0x000000d8];
};
esaigrp-2 {
fsl,pins = *
0x18003800 [0x000000f0];
};
};
flexcan1 {
flexcan1grp-1 {
fsl,pins = <0x0000020c
0x000005dc 0x000007e4 0x00000002 0x00000000 0x80000000 0x00000208
0x000005d8 0x00000000 0x00000002 0x00000000 0x80000000>;
linux,phandle = <0x00000008>;
phandle = <0x00000008>;
};
flexcan1grp-2 {
fsl,pins = <0x00000240
0x00000610 0x00000000 0x00000003 0x00000000 0x80000000 0x0000020c
0x000005dc 0x000007e4 0x00000002 0x00000000 0x80000000>;
};
};
flexcan2 {
flexcan2grp-1 {
fsl,pins = <0x00000218
0x000005e8 0x00000000 0x00000000 0x00000000 0x80000000 0x0000021c
0x000005ec 0x000007e8 0x00000000 0x00000000 0x80000000>;
};
};
gpmi-nand {
gpmi-nand-1 {
fsl,pins = *
0x18003a68 [0x00000198];
};
gpmi-nand-2 {
fsl,pins = *
0x18003c20 [0x00000180];
linux,phandle = <0x00000004>;
phandle = <0x00000004>;
};
};
hdmi_hdcp {
hdmihdcpgrp-1 {
fsl,pins = <0x00000210
0x000005e0 0x00000890 0x00000002 0x00000001 0x4001b8b1 0x00000214
0x000005e4 0x00000894 0x00000002 0x00000001 0x4001b8b1>;
};
hdmihdcpgrp-2 {
fsl,pins = <0x0000008c
0x000003a0 0x00000890 0x00000004 0x00000000 0x4001b8b1 0x00000090
0x000003a4 0x00000894 0x00000004 0x00000000 0x4001b8b1>;
};
hdmihdcpgrp-3 {
fsl,pins = <0x0000008c
0x000003a0 0x00000890 0x00000004 0x00000000 0x4001b8b1 0x00000214
0x000005e4 0x00000894 0x00000002 0x00000001 0x4001b8b1>;
};
};
hdmi_cec {
hdmicecgrp-1 {
fsl,pins = <0x00000088
0x0000039c 0x0000088c 0x00000006 0x00000000 0x0001f8b0>;
};
hdmicecgrp-2 {
fsl,pins = <0x0000020c
0x000005dc 0x0000088c 0x00000006 0x00000001 0x0001f8b0>;
};
};
i2c1 {
i2c1grp-1 {
fsl,pins = <0x000000a4
0x000003b8 0x00000898 0x00000006 0x00000000 0x4001b8b1 0x000000c4
0x000003d8 0x0000089c 0x00000001 0x00000000 0x4001b8b1>;
linux,phandle = <0x0000001a>;
phandle = <0x0000001a>;
};
i2c1grp-2 {
fsl,pins = <0x00000278
0x00000648 0x0000089c 0x00000004 0x00000001 0x4001b8b1 0x0000027c
0x0000064c 0x00000898 0x00000004 0x00000001 0x4001b8b1>;
};
};
i2c2 {
i2c2grp-1 {
fsl,pins = <0x0000008c
0x000003a0 0x000008a0 0x00000006 0x00000000 0x4001b8b1 0x00000090
0x000003a4 0x000008a4 0x00000006 0x00000000 0x4001b8b1>;
};
i2c2grp-2 {
fsl,pins = <0x00000210
0x000005e0 0x000008a0 0x00000004 0x00000001 0x4001b8b1 0x00000214
0x000005e4 0x000008a4 0x00000004 0x00000001 0x4001b8b1>;
linux,phandle = <0x0000001b>;
phandle = <0x0000001b>;
};
i2c2grp-3 {
fsl,pins = <0x0000008c
0x000003a0 0x000008a0 0x00000006 0x00000000 0x4001b8b1 0x00000214
0x000005e4 0x000008a4 0x00000004 0x00000001 0x4001b8b1>;
};
};
i2c3 {
i2c3grp-1 {
fsl,pins = <0x00000094
0x000003a8 0x000008a8 0x00000006 0x00000000 0x4001b8b1 0x00000098
0x000003ac 0x000008ac 0x00000006 0x00000000 0x4001b8b1>;
};
i2c3grp-2 {
fsl,pins = <0x0000022c
0x000005fc 0x000008a8 0x00000002 0x00000001 0x4001b8b1 0x00000230
0x00000600 0x000008ac 0x00000002 0x00000001 0x4001b8b1>;
linux,phandle = <0x0000001c>;
phandle = <0x0000001c>;
};
i2c3grp-3 {
fsl,pins = <0x0000023c
0x0000060c 0x000008a8 0x00000006 0x00000002 0x4001b8b1 0x00000248
0x00000618 0x000008ac 0x00000006 0x00000002 0x4001b8b1>;
};
i2c3grp-4 {
fsl,pins = <0x0000022c
0x000005fc 0x000008a8 0x00000002 0x00000001 0x4001b8b1 0x00000098
0x000003ac 0x000008ac 0x00000006 0x00000000 0x4001b8b1>;
};
};
ipu1 {
ipu1grp-1 {
fsl,pins = *
0x180042ec [0x000002b8];
};
ipu1grp-2 {
fsl,pins = *
0x180045c4 [0x00000120];
};
ipu1grp-3 {
fsl,pins = *
0x18004704 [0x000001c8];
};
};
mlb {
mlbgrp-1 {
fsl,pins = *
0x180048f8 [0x00000048];
};
mlbgrp-2 {
fsl,pins = *
0x18004960 [0x00000048];
};
};
pwm0 {
pwm0grp-1 {
fsl,pins = <0x00000344
0x0000072c 0x00000000 0x00000003 0x00000000 0x0001b0b1>;
};
};
pwm3 {
pwm3grp-1 {
fsl,pins = <0x00000320
0x00000708 0x00000000 0x00000002 0x00000000 0x0001b0b1>;
};
};
spdif {
spdifgrp-1 {
fsl,pins = <0x00000210
0x000005e0 0x00000914 0x00000006 0x00000002 0x0001b0b0>;
};
spdifgrp-2 {
fsl,pins = <0x00000248
0x00000618 0x00000914 0x00000004 0x00000003 0x0001b0b0 0x0000024c
0x0000061c 0x00000000 0x00000004 0x00000000 0x0001b0b0>;
};
spdifgrp-3 {
fsl,pins = <0x000001e4
0x000004f8 0x00000000 0x00000003 0x00000000 0x0001b0b0>;
};
};
uart1 {
uart1grp-1 {
fsl,pins = <0x00000280
0x00000650 0x00000000 0x00000003 0x00000000 0x0001b0b1 0x00000284
0x00000654 0x00000920 0x00000003 0x00000001 0x0001b0b1>;
};
uart1grp-2 {
fsl,pins = <0x000002a8
0x00000690 0x00000000 0x00000001 0x00000000 0x0001b0b1 0x000002ac
0x00000694 0x00000920 0x00000001 0x00000003 0x0001b0b1>;
linux,phandle = <0x00000007>;
phandle = <0x00000007>;
};
};
uart2 {
uart2grp-1 {
fsl,pins = <0x000000bc
0x000003d0 0x00000000 0x00000004 0x00000000 0x0001b0b1 0x000000c0
0x000003d4 0x00000928 0x00000004 0x00000001 0x0001b0b1>;
};
uart2grp-2 {
fsl,pins = *
0x18004c58 [0x00000060];
};
uart2grp-3 {
fsl,pins = <0x00000338
0x00000720 0x00000000 0x00000002 0x00000000 0x0001b0b1 0x0000032c
0x00000714 0x00000928 0x00000002 0x00000006 0x0001b0b1>;
linux,phandle = <0x0000001f>;
phandle = <0x0000001f>;
};
};
uart3 {
uart3grp-1 {
fsl,pins = *
0x18004d58 [0x00000060];
};
uart3grp-2 {
fsl,pins = *
0x18004dd8 [0x00000060];
};
uart3grp-3 {
fsl,pins = <0x000000b4
0x000003c8 0x00000000 0x00000002 0x00000000 0x0001b0b1 0x000000b8
0x000003cc 0x00000930 0x00000002 0x00000001 0x0001b0b1>;
};
};
uart4 {
uart4grp-1 {
fsl,pins = <0x000001f8
0x000005c8 0x00000000 0x00000004 0x00000000 0x0001b0b1 0x000001fc
0x000005cc 0x00000938 0x00000004 0x00000001 0x0001b0b1>;
};
};
uart5 {
uart5grp-1 {
fsl,pins = <0x00000200
0x000005d0 0x00000000 0x00000004 0x00000000 0x0001b0b1 0x00000204
0x000005d4 0x00000940 0x00000004 0x00000001 0x0001b0b1>;
linux,phandle = <0x00000020>;
phandle = <0x00000020>;
};
};
usbotg {
usbotggrp-1 {
fsl,pins = <0x00000224
0x000005f4 0x00000004 0x00000003 0xff0d0101 0x00017059>;
linux,phandle = <0x00000013>;
phandle = <0x00000013>;
};
usbotggrp-2 {
fsl,pins = <0x000001d8
0x000004ec 0x00000004 0x00000000 0xff0d0100 0x00017059>;
};
};
usbh2 {
usbh2grp-1 {
fsl,pins = <0x00000058
0x0000036c 0x00000000 0x00000000 0x00000000 0x40013030 0x00000074
0x00000388 0x00000000 0x00000000 0x00000000 0x40013030>;
};
usbh2grp-2 {
fsl,pins = <0x00000074
0x00000388 0x00000000 0x00000000 0x00000000 0x40017030>;
};
};
usbh3 {
usbh3grp-1 {
fsl,pins = <0x0000006c
0x00000380 0x00000000 0x00000000 0x00000000 0x40013030 0x00000084
0x00000398 0x00000000 0x00000000 0x00000000 0x40013030>;
};
usbh3grp-2 {
fsl,pins = <0x00000084
0x00000398 0x00000000 0x00000000 0x00000000 0x40017030>;
};
};
usdhc1 {
usdhc1grp-1 {
fsl,pins = *
0x18005168 [0x000000f0];
};
usdhc1grp-2 {
fsl,pins = *
0x18005278 [0x00000090];
};
};
usdhc2 {
usdhc2grp-1 {
fsl,pins = *
0x18005338 [0x000000f0];
};
usdhc2grp-2 {
fsl,pins = *
0x18005448 [0x00000090];
};
};
usdhc3 {
usdhc3grp-1 {
fsl,pins = *
0x18005508 [0x000000f0];
};
usdhc3grp-1-100mhz {
fsl,pins = *
0x18005620 [0x000000f0];
};
usdhc3grp-1-200mhz {
fsl,pins = *
0x18005738 [0x000000f0];
};
usdhc3grp-2 {
fsl,pins = *
0x18005848 [0x00000090];
linux,phandle = <0x00000017>;
phandle = <0x00000017>;
};
};
usdhc4 {
usdhc4grp-1 {
fsl,pins = *
0x18005928 [0x000000f0];
};
usdhc4grp-2 {
fsl,pins = *
0x18005a38 [0x00000090];
};
};
weim {
weim_cs0grp-1 {
fsl,pins = <0x000000f8
0x0000040c 0x00000000 0x00000000 0x00000000 0x0000b0b1>;
};
weim_norgrp-1 {
fsl,pins = *
0x18005b38 [0x00000408];
};
};
ipu2 {
ipu2grp-1 {
fsl,pins = *
0x18005f70 [0x000002b8];
};
};
hog {
hoggrp {
fsl,pins = *
0x18006250 [0x00000138];
linux,phandle = <0x0000000b>;
phandle = <0x0000000b>;
};
};
};
ldb@020e0008 {
#address-cells = <0x00000001>;
#size-cells = <0x00000000>;
compatible = "fsl,imx6q-ldb", "fsl,imx53-ldb";
gpr = <0x0000000c>;
status = "okay";
clocks = <0x00000002 0x00000021
0x00000002 0x00000022 0x00000002 0x00000027 0x00000002 0x00000028
0x00000002 0x00000029 0x00000002 0x0000002a 0x00000002 0x00000087
0x00000002 0x00000088>;
clock-names = "di0_pll", "di1_pll",
"di0_sel", "di1_sel", "di2_sel", "di3_sel", "di0", "di1";
lvds-channel@0 {
reg = <0x00000000>;
status = "disabled";
crtcs = <0x0000000d 0x00000000
0x0000000d 0x00000001 0x0000000e 0x00000000 0x0000000e 0x00000001>;
};
lvds-channel@1 {
reg = <0x00000001>;
status = "okay";
crtcs = <0x0000000d 0x00000000
0x0000000d 0x00000001 0x0000000e 0x00000000 0x0000000e 0x00000001>;
fsl,data-mapping = "spwg";
fsl,data-width = <0x00000012>;
display-timings {
native-mode = <0x0000000f>;
hsd100pxn1 {
clock-frequency = <0x03dfd240>;
hactive = <0x00000400>;
vactive = <0x00000300>;
hback-porch =
<0x000000dc>;
hfront-porch =
<0x00000028>;
vback-porch =
<0x00000015>;
vfront-porch =
<0x00000007>;
hsync-len =
<0x0000003c>;
vsync-len =
<0x0000000a>;
linux,phandle
= <0x0000000f>;
phandle = <0x0000000f>;
};
};
};
};
dcic@020e4000 {
reg = <0x020e4000 0x00004000>;
interrupts = <0x00000000 0x0000007c 0x00000004>;
};
dcic@020e8000 {
reg = <0x020e8000 0x00004000>;
interrupts = <0x00000000 0x0000007d 0x00000004>;
};
sdma@020ec000 {
compatible = "fsl,imx6q-sdma", "fsl,imx35-sdma";
reg = <0x020ec000 0x00004000>;
interrupts = <0x00000000 0x00000002 0x00000004>;
clocks = <0x00000002 0x0000009b
0x00000002 0x0000009b>;
clock-names = "ipg", "ahb";
#dma-cells = <0x00000003>;
fsl,sdma-ram-script-name =
"imx/sdma/sdma-imx6q.bin";
linux,phandle = <0x00000006>;
phandle = <0x00000006>;
};
};
aips-bus@02100000 {
compatible = "fsl,aips-bus", "simple-bus";
#address-cells = <0x00000001>;
#size-cells = <0x00000001>;
reg = <0x02100000 0x00100000>;
ranges;
caam@02100000 {
reg = <0x02100000 0x00040000>;
interrupts = <0x00000000 0x00000069
0x00000004 0x00000000 0x0000006a 0x00000004>;
};
aipstz@0217c000 {
reg = <0x0217c000 0x00004000>;
};
usb@02184000 {
compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
reg = <0x02184000 0x00000200>;
interrupts = <0x00000000 0x0000002b 0x00000004>;
clocks = <0x00000002 0x000000a2>;
fsl,usbphy = <0x00000010>;
fsl,usbmisc = <0x00000011 0x00000000>;
status = "okay";
vbus-supply = <0x00000012>;
pinctrl-names = "default";
pinctrl-0 = <0x00000013>;
disable-over-current;
};
usb@02184200 {
compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
reg = <0x02184200 0x00000200>;
interrupts = <0x00000000 0x00000028 0x00000004>;
clocks = <0x00000002 0x000000a2>;
fsl,usbphy = <0x00000014>;
fsl,usbmisc = <0x00000011 0x00000001>;
status = "okay";
vbus-supply = <0x00000015>;
};
usb@02184400 {
compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
reg = <0x02184400 0x00000200>;
interrupts = <0x00000000 0x00000029 0x00000004>;
clocks = <0x00000002 0x000000a2>;
fsl,usbmisc = <0x00000011 0x00000002>;
status = "disabled";
};
usb@02184600 {
compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
reg = <0x02184600 0x00000200>;
interrupts = <0x00000000 0x0000002a 0x00000004>;
clocks = <0x00000002 0x000000a2>;
fsl,usbmisc = <0x00000011 0x00000003>;
status = "disabled";
};
usbmisc@02184800 {
#index-cells = <0x00000001>;
compatible = "fsl,imx6q-usbmisc";
reg = <0x02184800 0x00000200>;
clocks = <0x00000002 0x000000a2>;
linux,phandle = <0x00000011>;
phandle = <0x00000011>;
};
ethernet@02188000 {
compatible = "fsl,imx6q-fec";
reg = <0x02188000 0x00004000>;
interrupts = <0x00000000 0x00000076
0x00000004 0x00000000 0x00000077 0x00000004>;
clocks = <0x00000002 0x00000075
0x00000002 0x00000075 0x00000002 0x000000be>;
clock-names = "ipg", "ahb", "ptp";
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <0x00000016>;
phy-mode = "rgmii";
phy-reset-gpios = <0x00000005
0x0000001e 0x00000000>;
};
mlb@0218c000 {
reg = <0x0218c000 0x00004000>;
interrupts = <0x00000000 0x00000035
0x00000004 0x00000000 0x00000075 0x00000004 0x00000000 0x0000007e
0x00000004>;
};
usdhc@02190000 {
compatible = "fsl,imx6q-usdhc";
reg = <0x02190000 0x00004000>;
interrupts = <0x00000000 0x00000016 0x00000004>;
clocks = <0x00000002 0x000000a3
0x00000002 0x000000a3 0x00000002 0x000000a3>;
clock-names = "ipg", "ahb", "per";
bus-width = <0x00000004>;
status = "disabled";
};
usdhc@02194000 {
compatible = "fsl,imx6q-usdhc";
reg = <0x02194000 0x00004000>;
interrupts = <0x00000000 0x00000017 0x00000004>;
clocks = <0x00000002 0x000000a4
0x00000002 0x000000a4 0x00000002 0x000000a4>;
clock-names = "ipg", "ahb", "per";
bus-width = <0x00000004>;
status = "disabled";
};
usdhc@02198000 {
compatible = "fsl,imx6q-usdhc";
reg = <0x02198000 0x00004000>;
interrupts = <0x00000000 0x00000018 0x00000004>;
clocks = <0x00000002 0x000000a5
0x00000002 0x000000a5 0x00000002 0x000000a5>;
clock-names = "ipg", "ahb", "per";
bus-width = <0x00000004>;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <0x00000017>;
cd-gpios = <0x00000018 0x00000000 0x00000000>;
vmmc-supply = <0x00000019>;
};
usdhc@0219c000 {
compatible = "fsl,imx6q-usdhc";
reg = <0x0219c000 0x00004000>;
interrupts = <0x00000000 0x00000019 0x00000004>;
clocks = <0x00000002 0x000000a6
0x00000002 0x000000a6 0x00000002 0x000000a6>;
clock-names = "ipg", "ahb", "per";
bus-width = <0x00000004>;
status = "disabled";
};
i2c@021a0000 {
#address-cells = <0x00000001>;
#size-cells = <0x00000000>;
compatible = "fsl,imx6q-i2c", "fsl,imx21-i2c";
reg = <0x021a0000 0x00004000>;
interrupts = <0x00000000 0x00000024 0x00000004>;
clocks = <0x00000002 0x0000007d>;
status = "okay";
clock-frequency = <0x000186a0>;
pinctrl-names = "default";
pinctrl-0 = <0x0000001a>;
eeprom@50 {
compatible = "atmel,24c02";
reg = <0x00000050>;
pagesize = <0x00000010>;
};
eeprom@51 {
compatible = "atmel,24c02";
reg = <0x00000051>;
pagesize = <0x00000010>;
};
eeprom@52 {
compatible = "atmel,24c02";
reg = <0x00000052>;
pagesize = <0x00000010>;
};
eeprom@53 {
compatible = "atmel,24c02";
reg = <0x00000053>;
pagesize = <0x00000010>;
};
pca9555@23 {
compatible = "nxp,pca9555";
reg = <0x00000023>;
gpio-controller;
#gpio-cells = <0x00000002>;
};
gsc@29 {
compatible = "gw,gsp";
reg = <0x00000029>;
};
ds1672@68 {
compatible = "dallas,ds1672";
reg = <0x00000068>;
};
};
i2c@021a4000 {
#address-cells = <0x00000001>;
#size-cells = <0x00000000>;
compatible = "fsl,imx6q-i2c", "fsl,imx21-i2c";
reg = <0x021a4000 0x00004000>;
interrupts = <0x00000000 0x00000025 0x00000004>;
clocks = <0x00000002 0x0000007e>;
status = "okay";
clock-frequency = <0x000186a0>;
pinctrl-names = "default";
pinctrl-0 = <0x0000001b>;
pfuze100@08 {
compatible = "fsl,pfuze100";
reg = <0x00000008>;
regulators {
sw1ab {
regulator-min-microvolt = <0x000493e0>;
regulator-max-microvolt = <0x001c9c38>;
regulator-boot-on;
regulator-always-on;
regulator-ramp-delay = <0x0000186a>;
};
sw1c {
regulator-min-microvolt = <0x000493e0>;
regulator-max-microvolt = <0x001c9c38>;
regulator-boot-on;
regulator-always-on;
regulator-ramp-delay = <0x0000186a>;
};
sw2 {
regulator-min-microvolt = "", "5";
regulator-max-microvolt = <0x003c45b0>;
regulator-boot-on;
regulator-always-on;
};
sw3a {
regulator-min-microvolt = <0x00061a80>;
regulator-max-microvolt = <0x001e22d8>;
regulator-boot-on;
regulator-always-on;
};
sw3b {
regulator-min-microvolt = <0x00061a80>;
regulator-max-microvolt = <0x001e22d8>;
regulator-boot-on;
regulator-always-on;
};
sw4 {
regulator-min-microvolt = "", "5";
regulator-max-microvolt = <0x00325aa0>;
linux,phandle
= <0x0000001d>;
phandle = <0x0000001d>;
};
swbst {
regulator-min-microvolt = <0x004c4b40>;
regulator-max-microvolt = <0x004e9530>;
};
vsnvs {
regulator-min-microvolt = <0x000f4240>;
regulator-max-microvolt = <0x002dc6c0>;
regulator-boot-on;
regulator-always-on;
};
vrefddr {
regulator-boot-on;
regulator-always-on;
};
vgen1 {
regulator-min-microvolt = "", "5";
regulator-max-microvolt = <0x0017a6b0>;
};
vgen2 {
regulator-min-microvolt = "", "5";
regulator-max-microvolt = <0x0017a6b0>;
};
vgen3 {
regulator-min-microvolt = <0x001b7740>;
regulator-max-microvolt = <0x00325aa0>;
};
vgen4 {
regulator-min-microvolt = <0x001b7740>;
regulator-max-microvolt = <0x00325aa0>;
regulator-always-on;
};
vgen5 {
regulator-min-microvolt = <0x001b7740>;
regulator-max-microvolt = <0x00325aa0>;
regulator-always-on;
};
vgen6 {
regulator-min-microvolt = <0x001b7740>;
regulator-max-microvolt = <0x00325aa0>;
regulator-always-on;
};
};
};
pex8609@3f {
compatible = "plx,pex8609";
reg = <0x0000003f>;
};
si52147@6b {
compatible = "sil,si52147";
reg = <0x0000006b>;
};
};
i2c@021a8000 {
#address-cells = <0x00000001>;
#size-cells = <0x00000000>;
compatible = "fsl,imx6q-i2c", "fsl,imx21-i2c";
reg = <0x021a8000 0x00004000>;
interrupts = <0x00000000 0x00000026 0x00000004>;
clocks = <0x00000002 0x0000007f>;
status = "okay";
clock-frequency = <0x000186a0>;
pinctrl-names = "default";
pinctrl-0 = <0x0000001c>;
fxos8700@1e {
compatible = "fsl,fxos8700";
reg = <0x0000001e>;
};
sgtl5000@0a {
compatible = "fsl,sgtl5000";
reg = <0x0000000a>;
clocks = <0x00000002 0x000000c9>;
VDDA-supply = <0x0000001d>;
VDDIO-supply = <0x00000019>;
linux,phandle = <0x00000029>;
phandle = <0x00000029>;
};
adv7611@4c {
compatible = "adi,adv7611";
reg = <0x0000004c>;
};
egalax_ts@04 {
compatible = "eeti,egalax_ts";
reg = <0x00000004>;
interrupt-parent = <0x00000018>;
interrupts = <0x0000000c 0x00000002>;
wakeup-gpios = <0x00000018
0x0000000c 0x00000000>;
};
adv7393@2a {
compatible = "adi,adv7393";
reg = <0x0000002a>;
};
adv7180@20 {
compatible = "adi,adv7180";
reg = <0x00000020>;
};
};
romcp@021ac000 {
reg = <0x021ac000 0x00004000>;
};
mmdc@021b0000 {
compatible = "fsl,imx6q-mmdc";
reg = <0x021b0000 0x00004000>;
};
mmdc@021b4000 {
reg = <0x021b4000 0x00004000>;
};
weim@021b8000 {
compatible = "fsl,imx6q-weim";
reg = <0x021b8000 0x00004000>;
interrupts = <0x00000000 0x0000000e 0x00000004>;
clocks = <0x00000002 0x000000c4>;
};
ocotp@021bc000 {
compatible = "fsl,imx6q-ocotp", "syscon";
reg = <0x021bc000 0x00004000>;
linux,phandle = <0x0000000a>;
phandle = <0x0000000a>;
};
tzasc@021d0000 {
reg = <0x021d0000 0x00004000>;
interrupts = <0x00000000 0x0000006c 0x00000004>;
};
tzasc@021d4000 {
reg = <0x021d4000 0x00004000>;
interrupts = <0x00000000 0x0000006d 0x00000004>;
};
audmux@021d8000 {
compatible = "fsl,imx6q-audmux",
"fsl,imx31-audmux";
reg = <0x021d8000 0x00004000>;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <0x0000001e>;
};
mipi@021dc000 {
reg = <0x021dc000 0x00004000>;
};
mipi@021e0000 {
reg = <0x021e0000 0x00004000>;
};
vdoa@021e4000 {
reg = <0x021e4000 0x00004000>;
interrupts = <0x00000000 0x00000012 0x00000004>;
};
serial@021e8000 {
compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
reg = <0x021e8000 0x00004000>;
interrupts = <0x00000000 0x0000001b 0x00000004>;
clocks = <0x00000002 0x000000a0
0x00000002 0x000000a1>;
clock-names = "ipg", "per";
dmas = <0x00000006 0x0000001b
0x00000004 0x00000000 0x00000006 0x0000001c 0x00000004 0x00000000>;
dma-names = "rx", "tx";
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <0x0000001f>;
};
serial@021f4000 {
compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
reg = <0x021f4000 0x00004000>;
interrupts = <0x00000000 0x0000001e 0x00000004>;
clocks = <0x00000002 0x000000a0
0x00000002 0x000000a1>;
clock-names = "ipg", "per";
dmas = <0x00000006 0x00000021
0x00000004 0x00000000 0x00000006 0x00000022 0x00000004 0x00000000>;
dma-names = "rx", "tx";
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <0x00000020>;
};
};
ipu@02400000 {
#crtc-cells = <0x00000001>;
compatible = "fsl,imx6q-ipu";
reg = <0x02400000 0x00400000>;
interrupts = <0x00000000 0x00000006 0x00000004
0x00000000 0x00000005 0x00000004>;
clocks = <0x00000002 0x00000082 0x00000002
0x00000083 0x00000002 0x00000084>;
clock-names = "bus", "di0", "di1";
resets = <0x00000021 0x00000002>;
linux,phandle = <0x0000000d>;
phandle = <0x0000000d>;
};
sram@00900000 {
compatible = "mmio-sram";
reg = <0x00900000 0x00040000>;
clocks = <0x00000002 0x0000008e>;
};
sata@02200000 {
compatible = "fsl,imx6q-ahci";
reg = <0x02200000 0x00004000>;
interrupts = <0x00000000 0x00000027 0x00000004>;
clocks = <0x00000002 0x0000009a 0x00000002
0x000000bb 0x00000002 0x00000069>;
clock-names = "sata", "sata_ref", "ahb";
status = "okay";
};
ipu@02800000 {
#crtc-cells = <0x00000001>;
compatible = "fsl,imx6q-ipu";
reg = <0x02800000 0x00400000>;
interrupts = <0x00000000 0x00000008 0x00000004
0x00000000 0x00000007 0x00000004>;
clocks = <0x00000002 0x00000085 0x00000002
0x00000086 0x00000002 0x00000089>;
clock-names = "bus", "di0", "di1";
resets = <0x00000021 0x00000004>;
linux,phandle = <0x0000000e>;
phandle = <0x0000000e>;
};
};
cpus {
#address-cells = <0x00000001>;
#size-cells = <0x00000000>;
cpu@0 {
compatible = "arm,cortex-a9";
device_type = "cpu";
reg = <0x00000000>;
next-level-cache = <0x00000022>;
operating-points = <0x00124f80 0x00137478
0x000f32a0 0x001312d0 0x000c15c0 0x00118c30 0x00060ae0 0x000e7ef0>;
clock-latency = <0x0000ee6c>;
clocks = <0x00000002 0x00000068 0x00000002
0x00000006 0x00000002 0x00000010 0x00000002 0x00000011 0x00000002
0x000000aa>;
clock-names = "arm", "pll2_pfd2_396m", "step",
"pll1_sw", "pll1_sys";
arm-supply = <0x00000023>;
pu-supply = <0x00000024>;
soc-supply = <0x00000025>;
};
cpu@1 {
compatible = "arm,cortex-a9";
device_type = "cpu";
reg = <0x00000001>;
next-level-cache = <0x00000022>;
};
cpu@2 {
compatible = "arm,cortex-a9";
device_type = "cpu";
reg = <0x00000002>;
next-level-cache = <0x00000022>;
};
cpu@3 {
compatible = "arm,cortex-a9";
device_type = "cpu";
reg = <0x00000003>;
next-level-cache = <0x00000022>;
};
};
leds {
compatible = "gpio-leds";
user1 {
label = "user1";
gpios = <0x00000026 0x00000006 0x00000000>;
default-state = "on";
linux,default-trigger = "heartbeat";
};
user2 {
label = "user2";
gpios = <0x00000026 0x00000007 0x00000000>;
default-state = "off";
};
user3 {
label = "user3";
gpios = <0x00000026 0x0000000f 0x00000001>;
default-state = "off";
};
};
pps {
compatible = "pps-gpio";
gpios = <0x00000005 0x0000001a 0x00000000>;
status = "okay";
};
regulators {
compatible = "simple-bus";
1p0v {
compatible = "regulator-fixed";
regulator-name = "1P0V";
regulator-min-microvolt = <0x000f4240>;
regulator-max-microvolt = <0x000f4240>;
regulator-always-on;
};
3p3v {
compatible = "regulator-fixed";
regulator-name = "3P3V";
regulator-min-microvolt = <0x00325aa0>;
regulator-max-microvolt = <0x00325aa0>;
regulator-always-on;
linux,phandle = <0x00000019>;
phandle = <0x00000019>;
};
usb_h1_vbus {
compatible = "regulator-fixed";
regulator-name = "usb_h1_vbus";
regulator-min-microvolt = <0x004c4b40>;
regulator-max-microvolt = <0x004c4b40>;
regulator-always-on;
linux,phandle = <0x00000015>;
phandle = <0x00000015>;
};
usb_otg_vbus {
compatible = "regulator-fixed";
regulator-name = "usb_otg_vbus";
regulator-min-microvolt = <0x004c4b40>;
regulator-max-microvolt = <0x004c4b40>;
gpio = <0x00000027 0x00000016 0x00000000>;
enable-active-high;
linux,phandle = <0x00000012>;
phandle = <0x00000012>;
};
};
sound {
compatible = "fsl,imx6q-sabrelite-sgtl5000",
"fsl,imx-audio-sgtl5000";
model = "imx6q-sabrelite-sgtl5000";
ssi-controller = <0x00000028>;
audio-codec = <0x00000029>;
audio-routing = "MIC_IN", "Mic Jack", "Mic Jack", "Mic
Bias", "Headphone Jack", "HP_OUT";
mux-int-port = <0x00000001>;
mux-ext-port = <0x00000004>;
};
};
Tim
>
> Jason
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
