On Tue, 2018-07-31 at 15:47 +0200, Alexandre Belloni wrote:
> The Microsemi Ocelot I2C controller is a designware IP. It also has a
> second set of registers to allow tweaking SDA hold time and spike
> filtering.
>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>
(except the bindings, not my area)
> Cc: Rob Herring <robh+dt@xxxxxxxxxx>
> Signed-off-by: Alexandre Belloni <alexandre.belloni@xxxxxxxxxxx>
> ---
> Changes in v2:
> - improved binding doc
> - changed the model handling as suggested by Andy
>
> .../bindings/i2c/i2c-designware.txt | 9 ++++-
> drivers/i2c/busses/i2c-designware-core.h | 3 ++
> drivers/i2c/busses/i2c-designware-platdrv.c | 40
> +++++++++++++++++++
> 3 files changed, 50 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/i2c/i2c-designware.txt
> b/Documentation/devicetree/bindings/i2c/i2c-designware.txt
> index fbb0a6d8b964..0fb17387c735 100644
> --- a/Documentation/devicetree/bindings/i2c/i2c-designware.txt
> +++ b/Documentation/devicetree/bindings/i2c/i2c-designware.txt
> @@ -2,7 +2,8 @@
>
> Required properties :
>
> - - compatible : should be "snps,designware-i2c"
> + - compatible : should be "snps,designware-i2c" or "mscc,ocelot-i2c"
> followed by
> + "snps,designware-i2c" for fallback
> - reg : Offset and length of the register set for the device
> - interrupts : <IRQ> where IRQ is the interrupt number.
>
> @@ -11,8 +12,12 @@ Recommended properties :
> - clock-frequency : desired I2C bus clock frequency in Hz.
>
> Optional properties :
> + - reg : for "mscc,ocelot-i2c", a second register set to configure
> the SDA hold
> + time, named ICPU_CFG:TWI_DELAY in the datasheet.
> +
> - i2c-sda-hold-time-ns : should contain the SDA hold time in
> nanoseconds.
> - This option is only supported in hardware blocks version 1.11a or
> newer.
> + This option is only supported in hardware blocks version 1.11a or
> newer and
> + on Microsemi SoCs ("mscc,ocelot-i2c" compatible).wtf
wtf?
>
> - i2c-scl-falling-time-ns : should contain the SCL falling time in
> nanoseconds.
> This value which is by default 300ns is used to compute the tLOW
> period.
> diff --git a/drivers/i2c/busses/i2c-designware-core.h
> b/drivers/i2c/busses/i2c-designware-core.h
> index 870444bbbcc4..5e240ce9968e 100644
> --- a/drivers/i2c/busses/i2c-designware-core.h
> +++ b/drivers/i2c/busses/i2c-designware-core.h
> @@ -225,6 +225,7 @@
> struct dw_i2c_dev {
> struct device *dev;
> void __iomem *base;
> + void __iomem *ext;
> struct completion cmd_complete;
> struct clk *clk;
> struct reset_control *rst;
> @@ -279,6 +280,8 @@ struct dw_i2c_dev {
> #define ACCESS_INTR_MASK 0x00000004
>
> #define MODEL_CHERRYTRAIL 0x00000100
> +#define MODEL_MSCC_OCELOT 0x00000200
> +#define MODEL_MASK 0x00000f00
>
> u32 dw_readl(struct dw_i2c_dev *dev, int offset);
> void dw_writel(struct dw_i2c_dev *dev, u32 b, int offset);
> diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c
> b/drivers/i2c/busses/i2c-designware-platdrv.c
> index ba142d7c0e05..68619b270b4c 100644
> --- a/drivers/i2c/busses/i2c-designware-platdrv.c
> +++ b/drivers/i2c/busses/i2c-designware-platdrv.c
> @@ -158,11 +158,48 @@ static inline int dw_i2c_acpi_configure(struct
> platform_device *pdev)
> #endif
>
> #ifdef CONFIG_OF
> +#define MSCC_ICPU_CFG_TWI_DELAY 0x0
> +#define MSCC_ICPU_CFG_TWI_DELAY_ENABLE BIT(0)
> +#define MSCC_ICPU_CFG_TWI_SPIKE_FILTER 0x4
> +
> +static int mscc_twi_set_sda_hold_time(struct dw_i2c_dev *dev)
> +{
> + writel((dev->sda_hold_time << 1) |
> MSCC_ICPU_CFG_TWI_DELAY_ENABLE,
> + dev->ext + MSCC_ICPU_CFG_TWI_DELAY);
> +
> + return 0;
> +}
> +
> +int dw_i2c_of_configure(struct platform_device *pdev)
> +{
> + struct dw_i2c_dev *dev = platform_get_drvdata(pdev);
> + struct resource *mem;
> +
> + switch (dev->flags & MODEL_MASK) {
> + case MODEL_MSCC_OCELOT:
> + mem = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> + dev->ext = devm_ioremap_resource(&pdev->dev, mem);
> + if (!IS_ERR(dev->ext))
> + dev->set_sda_hold_time =
> mscc_twi_set_sda_hold_time;
> + break;
> + default:
> + break;
> + }
> +
> + return 0;
> +}
> +
> static const struct of_device_id dw_i2c_of_match[] = {
> { .compatible = "snps,designware-i2c", },
> + { .compatible = "mscc,ocelot-i2c", .data = (void
> *)MODEL_MSCC_OCELOT },
> {},
> };
> MODULE_DEVICE_TABLE(of, dw_i2c_of_match);
> +#else
> +static inline int dw_i2c_of_configure(struct platform_device *pdev)
> +{
> + return -ENODEV;
> +}
> #endif
>
> static void i2c_dw_configure_master(struct dw_i2c_dev *dev)
> @@ -275,6 +312,9 @@ static int dw_i2c_plat_probe(struct
> platform_device *pdev)
>
> dev->flags |= (u32)device_get_match_data(&pdev->dev);
>
> + if (pdev->dev.of_node)
> + dw_i2c_of_configure(pdev);
> +
> acpi_speed = i2c_acpi_find_bus_speed(&pdev->dev);
> /*
> * Some DSTDs use a non standard speed, round down to the
> lowest
--
Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>
Intel Finland Oy
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
