[PATCH v2 2/5] regulator: rk808: add RK809 and RK817 support.

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



    Add support for the rk809 and rk817 regulator driver.
    Their specifications are as follows:
    1、The RK809 and RK809 consist of 5 DCDCs, 9 LDOs
       and have the same registers for these components except dcdc5.
    2、The dcdc5 is a boost dcdc for RK817 and is a buck for RK809.
    3、The RK817 has one switch but The Rk809 has two.

    The output voltages are configurable and are meant to supply power
    to the main processor and other components.

Signed-off-by: Tony Xie <tony.xie@xxxxxxxxxxxxxx>
---
 drivers/regulator/Kconfig           |   4 +-
 drivers/regulator/rk808-regulator.c | 633 +++++++++++++++++++++++++++++++++++-
 include/linux/mfd/rk808.h           |   3 +
 3 files changed, 637 insertions(+), 3 deletions(-)

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 5dbccf5..27ff89f 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -716,11 +716,11 @@ config REGULATOR_RC5T583
 	  outputs which can be controlled by i2c communication.
 
 config REGULATOR_RK808
-	tristate "Rockchip RK805/RK808/RK818 Power regulators"
+	tristate "Rockchip RK805/RK808/RK809/RK817/RK818 Power regulators"
 	depends on MFD_RK808
 	help
 	  Select this option to enable the power regulator of ROCKCHIP
-	  PMIC RK805,RK808 and RK818.
+	  PMIC RK805,RK809&RK817,RK808 and RK818.
 	  This driver supports the control of different power rails of device
 	  through regulator interface. The device supports multiple DCDC/LDO
 	  outputs which can be controlled by i2c communication.
diff --git a/drivers/regulator/rk808-regulator.c b/drivers/regulator/rk808-regulator.c
index 213b687..9edce22 100644
--- a/drivers/regulator/rk808-regulator.c
+++ b/drivers/regulator/rk808-regulator.c
@@ -36,6 +36,12 @@
 #define RK808_BUCK4_VSEL_MASK	0xf
 #define RK808_LDO_VSEL_MASK	0x1f
 
+#define RK809_BUCK5_VSEL_MASK		0x7
+
+#define RK817_LDO_VSEL_MASK		0x7f
+#define RK817_BOOST_VSEL_MASK		0x7
+#define RK817_BUCK_VSEL_MASK		0x7f
+
 #define RK818_BUCK_VSEL_MASK		0x3f
 #define RK818_BUCK4_VSEL_MASK		0x1f
 #define RK818_LDO_VSEL_MASK		0x1f
@@ -65,6 +71,9 @@
 /* max steps for increase voltage of Buck1/2, equal 100mv*/
 #define MAX_STEPS_ONE_TIME 8
 
+#define ENABLE_MASK(id)			(BIT(id) | BIT(4 + (id)))
+#define DISABLE_VAL(id)			(BIT(4 + (id)))
+
 #define RK805_DESC(_id, _match, _supply, _min, _max, _step, _vreg,      \
 	_vmask, _ereg, _emask, _etime)                                  \
 	[_id] = {                                                       \
@@ -86,6 +95,70 @@
 		.ops            = &rk805_reg_ops,                       \
 	}
 
+#define RK817_DESC(_id, _match, _supply, _min, _max, _step, _vreg,	\
+	_vmask, _ereg, _emask, _enval, _disval, _etime)		\
+	{							\
+		.name		= (_match),				\
+		.supply_name	= (_supply),				\
+		.of_match	= of_match_ptr(_match),			\
+		.regulators_node = of_match_ptr("regulators"),		\
+		.type		= REGULATOR_VOLTAGE,			\
+		.id		= (_id),				\
+		.n_voltages	= (((_max) - (_min)) / (_step) + 1),	\
+		.owner		= THIS_MODULE,				\
+		.min_uV		= (_min) * 1000,			\
+		.uV_step	= (_step) * 1000,			\
+		.vsel_reg	= (_vreg),				\
+		.vsel_mask	= (_vmask),				\
+		.enable_reg	= (_ereg),				\
+		.enable_mask	= (_emask),				\
+		.enable_val     = (_enval),				\
+		.disable_val     = (_disval),				\
+		.enable_time	= (_etime),				\
+		.ops		= &rk817_reg_ops,			\
+	}
+
+#define RK817_BOOST_DESC(_id, _match, _supply, _min, _max, _step, _vreg,\
+	_vmask, _ereg, _emask, _enval, _disval, _etime, m_drop)		\
+	{							\
+		.name		= (_match),				\
+		.supply_name	= (_supply),				\
+		.of_match	= of_match_ptr(_match),			\
+		.regulators_node = of_match_ptr("regulators"),		\
+		.type		= REGULATOR_VOLTAGE,			\
+		.id		= (_id),				\
+		.n_voltages	= (((_max) - (_min)) / (_step) + 1),	\
+		.owner		= THIS_MODULE,				\
+		.min_uV		= (_min) * 1000,			\
+		.uV_step	= (_step) * 1000,			\
+		.vsel_reg	= (_vreg),				\
+		.vsel_mask	= (_vmask),				\
+		.enable_reg	= (_ereg),				\
+		.enable_mask	= (_emask),				\
+		.enable_val     = (_enval),				\
+		.disable_val     = (_disval),				\
+		.enable_time	= (_etime),				\
+		.min_dropout_uV = (m_drop) * 1000,			\
+		.ops		= &rk817_boost_ops,			\
+	}
+
+#define RK817_DESC_SWITCH(_id, _match, _supply, _ereg, _emask,\
+	_enval, _disval)		\
+	{							\
+		.name		= (_match),				\
+		.supply_name	= (_supply),				\
+		.of_match	= of_match_ptr(_match),			\
+		.regulators_node = of_match_ptr("regulators"),		\
+		.type		= REGULATOR_VOLTAGE,			\
+		.id		= (_id),				\
+		.enable_reg	= (_ereg),				\
+		.enable_mask	= (_emask),				\
+		.enable_val     = (_enval),				\
+		.disable_val     = (_disval),				\
+		.owner		= THIS_MODULE,				\
+		.ops		= &rk817_switch_ops			\
+	}
+
 #define RK8XX_DESC(_id, _match, _supply, _min, _max, _step, _vreg,	\
 	_vmask, _ereg, _emask, _etime)					\
 	[_id] = {							\
@@ -121,7 +194,6 @@
 		.ops		= &rk808_switch_ops			\
 	}
 
-
 struct rk808_regulator_data {
 	struct gpio_desc *dvs_gpio[2];
 };
@@ -138,6 +210,51 @@ struct rk808_regulator_data {
 	REGULATOR_LINEAR_RANGE(2500000, 15, 15, 0),
 };
 
+#define RK809_BUCK5_SEL_CNT		(8)
+
+static const struct regulator_linear_range rk809_buck5_voltage_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1500000, 0, 0, 0),
+	REGULATOR_LINEAR_RANGE(1800000, 1, 3, 200000),
+	REGULATOR_LINEAR_RANGE(2800000, 4, 5, 200000),
+	REGULATOR_LINEAR_RANGE(3300000, 6, 7, 300000),
+};
+
+#define RK817_BUCK1_MIN0 500000
+#define RK817_BUCK1_MAX0 1500000
+
+#define RK817_BUCK1_MIN1 1600000
+#define RK817_BUCK1_MAX1 2400000
+
+#define RK817_BUCK3_MAX1 3400000
+
+#define RK817_BUCK1_STP0 12500
+#define RK817_BUCK1_STP1 100000
+
+#define RK817_BUCK1_SEL0 ((RK817_BUCK1_MAX0 - RK817_BUCK1_MIN0) /\
+						  RK817_BUCK1_STP0)
+#define RK817_BUCK1_SEL1 ((RK817_BUCK1_MAX1 - RK817_BUCK1_MIN1) /\
+						  RK817_BUCK1_STP1)
+
+#define RK817_BUCK3_SEL1 ((RK817_BUCK3_MAX1 - RK817_BUCK1_MIN1) /\
+						  RK817_BUCK1_STP1)
+
+#define RK817_BUCK1_SEL_CNT (RK817_BUCK1_SEL0 + RK817_BUCK1_SEL1 + 1)
+#define RK817_BUCK3_SEL_CNT (RK817_BUCK1_SEL0 + RK817_BUCK3_SEL1 + 1)
+
+static const struct regulator_linear_range rk817_buck1_voltage_ranges[] = {
+	REGULATOR_LINEAR_RANGE(RK817_BUCK1_MIN0, 0,
+			       RK817_BUCK1_SEL0, RK817_BUCK1_STP0),
+	REGULATOR_LINEAR_RANGE(RK817_BUCK1_MIN1, RK817_BUCK1_SEL0 + 1,
+			       RK817_BUCK1_SEL_CNT, RK817_BUCK1_STP1),
+};
+
+static const struct regulator_linear_range rk817_buck3_voltage_ranges[] = {
+	REGULATOR_LINEAR_RANGE(RK817_BUCK1_MIN0, 0,
+			       RK817_BUCK1_SEL0, RK817_BUCK1_STP0),
+	REGULATOR_LINEAR_RANGE(RK817_BUCK1_MIN1, RK817_BUCK1_SEL0 + 1,
+			       RK817_BUCK3_SEL_CNT, RK817_BUCK1_STP1),
+};
+
 static int rk808_buck1_2_get_voltage_sel_regmap(struct regulator_dev *rdev)
 {
 	struct rk808_regulator_data *pdata = rdev_get_drvdata(rdev);
@@ -289,6 +406,35 @@ static int rk808_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay)
 				  RK808_RAMP_RATE_MASK, ramp_value);
 }
 
+/*
+ * RK817 RK809
+ */
+static int rk817_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay)
+{
+	unsigned int ramp_value = RK817_RAMP_RATE_25MV_PER_US;
+	unsigned int reg = RK817_BUCK_CONFIG_REG(rdev_get_id(rdev));
+
+	switch (ramp_delay) {
+	case 0 ... 3000:
+		ramp_value = RK817_RAMP_RATE_3MV_PER_US;
+		break;
+	case 3001 ... 6300:
+		ramp_value = RK817_RAMP_RATE_6_3MV_PER_US;
+		break;
+	case 6301 ... 12500:
+		ramp_value = RK817_RAMP_RATE_12_5MV_PER_US;
+		break;
+	case 12501 ... 25000:
+		break;
+	default:
+		pr_warn("%s ramp_delay: %d not supported, setting 10000\n",
+			rdev->desc->name, ramp_delay);
+	}
+
+	return regmap_update_bits(rdev->regmap, reg,
+				  RK817_RAMP_RATE_MASK, ramp_value);
+}
+
 static int rk808_set_suspend_voltage(struct regulator_dev *rdev, int uv)
 {
 	unsigned int reg;
@@ -304,6 +450,29 @@ static int rk808_set_suspend_voltage(struct regulator_dev *rdev, int uv)
 				  sel);
 }
 
+static int rk817_check_suspend_voltage(int id)
+{
+	if (id >= RK817_ID_DCDC1 && id <= RK817_ID_LDO9)
+		return 0;
+	return -1;
+}
+
+static int rk817_set_suspend_voltage(struct regulator_dev *rdev, int uv)
+{
+	unsigned int reg;
+	int id = rdev_get_id(rdev);
+	int sel = regulator_map_voltage_linear(rdev, uv, uv);
+	/* only ldo1~ldo9 */
+	if (sel < 0 || rk817_check_suspend_voltage(id))
+		return -EINVAL;
+
+	reg = rdev->desc->vsel_reg + RK808_SLP_REG_OFFSET;
+
+	return regmap_update_bits(rdev->regmap, reg,
+				  rdev->desc->vsel_mask,
+				  sel);
+}
+
 static int rk808_set_suspend_voltage_range(struct regulator_dev *rdev, int uv)
 {
 	unsigned int reg;
@@ -363,6 +532,129 @@ static int rk808_set_suspend_disable(struct regulator_dev *rdev)
 				  rdev->desc->enable_mask);
 }
 
+static int rk817_set_suspend_enable_ctrl(struct regulator_dev *rdev,
+					 unsigned int en)
+{
+	unsigned int reg;
+	int id = rdev_get_id(rdev);
+	unsigned int id_slp, msk, val;
+
+	if (id >= RK817_ID_DCDC1 && id <= RK817_ID_DCDC4)
+		id_slp = id;
+	else if (id >= RK817_ID_LDO1 && id <= RK817_ID_LDO8)
+		id_slp = 8 + (id - RK817_ID_LDO1);
+	else if (id >= RK817_ID_LDO9 && id <= RK809_ID_SW2)
+		id_slp = 4 + (id - RK817_ID_LDO9);
+	else
+		return -EINVAL;
+
+	reg = RK817_POWER_SLP_EN_REG(id_slp / 8);
+
+	msk = BIT(id_slp % 8);
+	if (en)
+		val = msk;
+	else
+		val = 0;
+
+	return regmap_update_bits(rdev->regmap, reg, msk, val);
+}
+
+static int rk817_set_suspend_enable(struct regulator_dev *rdev)
+{
+	return rk817_set_suspend_enable_ctrl(rdev, 1);
+}
+
+static int rk817_set_suspend_disable(struct regulator_dev *rdev)
+{
+	return rk817_set_suspend_enable_ctrl(rdev, 0);
+}
+
+static int rk8xx_set_suspend_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+	unsigned int reg;
+
+	reg = rdev->desc->vsel_reg + RK808_SLP_REG_OFFSET;
+
+	switch (mode) {
+	case REGULATOR_MODE_FAST:
+		return regmap_update_bits(rdev->regmap, reg,
+					  PWM_MODE_MSK, FPWM_MODE);
+	case REGULATOR_MODE_NORMAL:
+		return regmap_update_bits(rdev->regmap, reg,
+					  PWM_MODE_MSK, AUTO_PWM_MODE);
+	default:
+		pr_err("do not support this mode\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int rk8xx_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+	switch (mode) {
+	case REGULATOR_MODE_FAST:
+		return regmap_update_bits(rdev->regmap, rdev->desc->vsel_reg,
+					  PWM_MODE_MSK, FPWM_MODE);
+	case REGULATOR_MODE_NORMAL:
+		return regmap_update_bits(rdev->regmap, rdev->desc->vsel_reg,
+					  PWM_MODE_MSK, AUTO_PWM_MODE);
+	default:
+		pr_err("do not support this mode\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static unsigned int rk8xx_get_mode(struct regulator_dev *rdev)
+{
+	unsigned int val;
+	int err;
+
+	err = regmap_read(rdev->regmap, rdev->desc->vsel_reg, &val);
+	if (err)
+		return err;
+
+	if (val & FPWM_MODE)
+		return REGULATOR_MODE_FAST;
+	else
+		return REGULATOR_MODE_NORMAL;
+}
+
+static int rk8xx_is_enabled_wmsk_regmap(struct regulator_dev *rdev)
+{
+	unsigned int val;
+	int ret;
+
+	ret = regmap_read(rdev->regmap, rdev->desc->enable_reg, &val);
+	if (ret != 0)
+		return ret;
+
+	/* add write mask bit */
+	val |= (rdev->desc->enable_mask & 0xf0);
+	val &= rdev->desc->enable_mask;
+
+	if (rdev->desc->enable_is_inverted) {
+		if (rdev->desc->enable_val)
+			return val != rdev->desc->enable_val;
+		return (val == 0);
+	}
+	if (rdev->desc->enable_val)
+		return val == rdev->desc->enable_val;
+	return val != 0;
+}
+
+static unsigned int rk8xx_regulator_of_map_mode(unsigned int mode)
+{
+	if (mode == 1)
+		return REGULATOR_MODE_FAST;
+	if (mode == 2)
+		return REGULATOR_MODE_NORMAL;
+
+	return -EINVAL;
+}
+
 static struct regulator_ops rk805_reg_ops = {
 		.list_voltage           = regulator_list_voltage_linear,
 		.map_voltage            = regulator_map_voltage_linear,
@@ -433,6 +725,71 @@ static int rk808_set_suspend_disable(struct regulator_dev *rdev)
 	.set_suspend_disable	= rk808_set_suspend_disable,
 };
 
+static struct regulator_ops rk809_buck5_ops_range = {
+	.list_voltage		= regulator_list_voltage_linear_range,
+	.map_voltage		= regulator_map_voltage_linear_range,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.set_voltage_time_sel	= regulator_set_voltage_time_sel,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= rk8xx_is_enabled_wmsk_regmap,
+	.set_suspend_voltage	= rk808_set_suspend_voltage_range,
+	.set_suspend_enable	= rk817_set_suspend_enable,
+	.set_suspend_disable	= rk817_set_suspend_disable,
+};
+
+static struct regulator_ops rk817_reg_ops = {
+	.list_voltage		= regulator_list_voltage_linear,
+	.map_voltage		= regulator_map_voltage_linear,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= rk8xx_is_enabled_wmsk_regmap,
+	.set_suspend_voltage	= rk817_set_suspend_voltage,
+	.set_suspend_enable	= rk817_set_suspend_enable,
+	.set_suspend_disable	= rk817_set_suspend_disable,
+};
+
+static struct regulator_ops rk817_boost_ops = {
+	.list_voltage		= regulator_list_voltage_linear,
+	.map_voltage		= regulator_map_voltage_linear,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= rk8xx_is_enabled_wmsk_regmap,
+	.set_suspend_enable	= rk817_set_suspend_enable,
+	.set_suspend_disable	= rk817_set_suspend_disable,
+};
+
+static struct regulator_ops rk817_buck_ops_range = {
+	.list_voltage		= regulator_list_voltage_linear_range,
+	.map_voltage		= regulator_map_voltage_linear_range,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.set_voltage_time_sel	= regulator_set_voltage_time_sel,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= rk8xx_is_enabled_wmsk_regmap,
+	.set_mode		= rk8xx_set_mode,
+	.get_mode		= rk8xx_get_mode,
+	.set_suspend_mode	= rk8xx_set_suspend_mode,
+	.set_ramp_delay		= rk817_set_ramp_delay,
+	.set_suspend_voltage	= rk808_set_suspend_voltage_range,
+	.set_suspend_enable	= rk817_set_suspend_enable,
+	.set_suspend_disable	= rk817_set_suspend_disable,
+};
+
+static struct regulator_ops rk817_switch_ops = {
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= regulator_is_enabled_regmap,
+	.set_suspend_enable	= rk817_set_suspend_enable,
+	.set_suspend_disable	= rk817_set_suspend_disable,
+};
+
 static const struct regulator_desc rk805_reg[] = {
 	{
 		.name = "DCDC_REG1",
@@ -589,6 +946,271 @@ static int rk808_set_suspend_disable(struct regulator_dev *rdev)
 		RK808_DCDC_EN_REG, BIT(6)),
 };
 
+static const struct regulator_desc rk809_reg[] = {
+	{
+		.name = "DCDC_REG1",
+		.supply_name = "vcc1",
+		.of_match = of_match_ptr("DCDC_REG1"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = RK817_ID_DCDC1,
+		.ops = &rk817_buck_ops_range,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = RK817_BUCK1_SEL_CNT + 1,
+		.linear_ranges = rk817_buck1_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges),
+		.vsel_reg = RK817_BUCK1_ON_VSEL_REG,
+		.vsel_mask = RK817_BUCK_VSEL_MASK,
+		.enable_reg = RK817_POWER_EN_REG(0),
+		.enable_mask = ENABLE_MASK(RK817_ID_DCDC1),
+		.enable_val = ENABLE_MASK(RK817_ID_DCDC1),
+		.disable_val = DISABLE_VAL(RK817_ID_DCDC1),
+		.of_map_mode = rk8xx_regulator_of_map_mode,
+		.owner = THIS_MODULE,
+	}, {
+		.name = "DCDC_REG2",
+		.supply_name = "vcc2",
+		.of_match = of_match_ptr("DCDC_REG2"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = RK817_ID_DCDC2,
+		.ops = &rk817_buck_ops_range,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = RK817_BUCK1_SEL_CNT + 1,
+		.linear_ranges = rk817_buck1_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges),
+		.vsel_reg = RK817_BUCK2_ON_VSEL_REG,
+		.vsel_mask = RK817_BUCK_VSEL_MASK,
+		.enable_reg = RK817_POWER_EN_REG(0),
+		.enable_mask = ENABLE_MASK(RK817_ID_DCDC2),
+		.enable_val = ENABLE_MASK(RK817_ID_DCDC2),
+		.disable_val = DISABLE_VAL(RK817_ID_DCDC2),
+		.of_map_mode = rk8xx_regulator_of_map_mode,
+		.owner = THIS_MODULE,
+	}, {
+		.name = "DCDC_REG3",
+		.supply_name = "vcc3",
+		.of_match = of_match_ptr("DCDC_REG3"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = RK817_ID_DCDC3,
+		.ops = &rk817_buck_ops_range,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = RK817_BUCK1_SEL_CNT + 1,
+		.linear_ranges = rk817_buck1_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges),
+		.vsel_reg = RK817_BUCK3_ON_VSEL_REG,
+		.vsel_mask = RK817_BUCK_VSEL_MASK,
+		.enable_reg = RK817_POWER_EN_REG(0),
+		.enable_mask = ENABLE_MASK(RK817_ID_DCDC3),
+		.enable_val = ENABLE_MASK(RK817_ID_DCDC3),
+		.disable_val = DISABLE_VAL(RK817_ID_DCDC3),
+		.of_map_mode = rk8xx_regulator_of_map_mode,
+		.owner = THIS_MODULE,
+	}, {
+		.name = "DCDC_REG4",
+		.supply_name = "vcc4",
+		.of_match = of_match_ptr("DCDC_REG4"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = RK817_ID_DCDC4,
+		.ops = &rk817_buck_ops_range,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = RK817_BUCK3_SEL_CNT + 1,
+		.linear_ranges = rk817_buck3_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(rk817_buck3_voltage_ranges),
+		.vsel_reg = RK817_BUCK4_ON_VSEL_REG,
+		.vsel_mask = RK817_BUCK_VSEL_MASK,
+		.enable_reg = RK817_POWER_EN_REG(0),
+		.enable_mask = ENABLE_MASK(RK817_ID_DCDC4),
+		.enable_val = ENABLE_MASK(RK817_ID_DCDC4),
+		.disable_val = DISABLE_VAL(RK817_ID_DCDC4),
+		.of_map_mode = rk8xx_regulator_of_map_mode,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "DCDC_REG5",
+		.supply_name = "vcc9",
+		.of_match = of_match_ptr("DCDC_REG5"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = RK809_ID_DCDC5,
+		.ops = &rk809_buck5_ops_range,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = RK809_BUCK5_SEL_CNT,
+		.linear_ranges = rk809_buck5_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(rk809_buck5_voltage_ranges),
+		.vsel_reg = RK809_BUCK5_CONFIG(0),
+		.vsel_mask = RK809_BUCK5_VSEL_MASK,
+		.enable_reg = RK817_POWER_EN_REG(3),
+		.enable_mask = ENABLE_MASK(1),
+		.enable_val = ENABLE_MASK(1),
+		.disable_val = DISABLE_VAL(1),
+		.of_map_mode = rk8xx_regulator_of_map_mode,
+		.owner = THIS_MODULE,
+	},
+	RK817_DESC(RK817_ID_LDO1, "LDO_REG1", "vcc5", 600, 3400, 25,
+		   RK817_LDO_ON_VSEL_REG(0), RK817_LDO_VSEL_MASK,
+		   RK817_POWER_EN_REG(1), ENABLE_MASK(0), ENABLE_MASK(0),
+		   DISABLE_VAL(0), 400),
+	RK817_DESC(RK817_ID_LDO2, "LDO_REG2", "vcc5", 600, 3400, 25,
+		   RK817_LDO_ON_VSEL_REG(1), RK817_LDO_VSEL_MASK,
+		   RK817_POWER_EN_REG(1), ENABLE_MASK(1), ENABLE_MASK(1),
+		   DISABLE_VAL(1), 400),
+	RK817_DESC(RK817_ID_LDO3, "LDO_REG3", "vcc5", 600, 3400, 25,
+		   RK817_LDO_ON_VSEL_REG(2), RK817_LDO_VSEL_MASK,
+		   RK817_POWER_EN_REG(1), ENABLE_MASK(2), ENABLE_MASK(2),
+		   DISABLE_VAL(2), 400),
+	RK817_DESC(RK817_ID_LDO4, "LDO_REG4", "vcc6", 600, 3400, 25,
+		   RK817_LDO_ON_VSEL_REG(3), RK817_LDO_VSEL_MASK,
+		   RK817_POWER_EN_REG(1), ENABLE_MASK(3), ENABLE_MASK(3),
+		   DISABLE_VAL(3), 400),
+	RK817_DESC(RK817_ID_LDO5, "LDO_REG5", "vcc6", 600, 3400, 25,
+		   RK817_LDO_ON_VSEL_REG(4), RK817_LDO_VSEL_MASK,
+		   RK817_POWER_EN_REG(2), ENABLE_MASK(0), ENABLE_MASK(0),
+		   DISABLE_VAL(0), 400),
+	RK817_DESC(RK817_ID_LDO6, "LDO_REG6", "vcc6", 600, 3400, 25,
+		   RK817_LDO_ON_VSEL_REG(5), RK817_LDO_VSEL_MASK,
+		   RK817_POWER_EN_REG(2), ENABLE_MASK(1), ENABLE_MASK(1),
+		   DISABLE_VAL(1), 400),
+	RK817_DESC(RK817_ID_LDO7, "LDO_REG7", "vcc7", 600, 3400, 25,
+		   RK817_LDO_ON_VSEL_REG(6), RK817_LDO_VSEL_MASK,
+		   RK817_POWER_EN_REG(2), ENABLE_MASK(2), ENABLE_MASK(2),
+		   DISABLE_VAL(2), 400),
+	RK817_DESC(RK817_ID_LDO8, "LDO_REG8", "vcc7", 600, 3400, 25,
+		   RK817_LDO_ON_VSEL_REG(7), RK817_LDO_VSEL_MASK,
+		   RK817_POWER_EN_REG(2), ENABLE_MASK(3), ENABLE_MASK(3),
+		   DISABLE_VAL(3), 400),
+	RK817_DESC(RK817_ID_LDO9, "LDO_REG9", "vcc7", 600, 3400, 25,
+		   RK817_LDO_ON_VSEL_REG(8), RK817_LDO_VSEL_MASK,
+		   RK817_POWER_EN_REG(3), ENABLE_MASK(0), ENABLE_MASK(0),
+		   DISABLE_VAL(0), 400),
+	RK817_DESC_SWITCH(RK809_ID_SW1, "SWITCH_REG1", "vcc8",
+			  RK817_POWER_EN_REG(3), ENABLE_MASK(3),
+			  ENABLE_MASK(3), DISABLE_VAL(3)),
+	RK817_DESC_SWITCH(RK809_ID_SW2, "SWITCH_REG2", "vcc9",
+			  RK817_POWER_EN_REG(3), ENABLE_MASK(2),
+			  ENABLE_MASK(2), DISABLE_VAL(2)),
+};
+
+static const struct regulator_desc rk817_reg[] = {
+	{
+		.name = "DCDC_REG1",
+		.supply_name = "vcc1",
+		.of_match = of_match_ptr("DCDC_REG1"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = RK817_ID_DCDC1,
+		.ops = &rk817_buck_ops_range,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = RK817_BUCK1_SEL_CNT + 1,
+		.linear_ranges = rk817_buck1_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges),
+		.vsel_reg = RK817_BUCK1_ON_VSEL_REG,
+		.vsel_mask = RK817_BUCK_VSEL_MASK,
+		.enable_reg = RK817_POWER_EN_REG(0),
+		.enable_mask = ENABLE_MASK(RK817_ID_DCDC1),
+		.enable_val = ENABLE_MASK(RK817_ID_DCDC1),
+		.disable_val = DISABLE_VAL(RK817_ID_DCDC1),
+		.of_map_mode = rk8xx_regulator_of_map_mode,
+		.owner = THIS_MODULE,
+	}, {
+		.name = "DCDC_REG2",
+		.supply_name = "vcc2",
+		.of_match = of_match_ptr("DCDC_REG2"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = RK817_ID_DCDC2,
+		.ops = &rk817_buck_ops_range,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = RK817_BUCK1_SEL_CNT + 1,
+		.linear_ranges = rk817_buck1_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges),
+		.vsel_reg = RK817_BUCK2_ON_VSEL_REG,
+		.vsel_mask = RK817_BUCK_VSEL_MASK,
+		.enable_reg = RK817_POWER_EN_REG(0),
+		.enable_mask = ENABLE_MASK(RK817_ID_DCDC2),
+		.enable_val = ENABLE_MASK(RK817_ID_DCDC2),
+		.disable_val = DISABLE_VAL(RK817_ID_DCDC2),
+		.of_map_mode = rk8xx_regulator_of_map_mode,
+		.owner = THIS_MODULE,
+	}, {
+		.name = "DCDC_REG3",
+		.supply_name = "vcc3",
+		.of_match = of_match_ptr("DCDC_REG3"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = RK817_ID_DCDC3,
+		.ops = &rk817_buck_ops_range,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = RK817_BUCK1_SEL_CNT + 1,
+		.linear_ranges = rk817_buck1_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges),
+		.vsel_reg = RK817_BUCK3_ON_VSEL_REG,
+		.vsel_mask = RK817_BUCK_VSEL_MASK,
+		.enable_reg = RK817_POWER_EN_REG(0),
+		.enable_mask = ENABLE_MASK(RK817_ID_DCDC3),
+		.enable_val = ENABLE_MASK(RK817_ID_DCDC3),
+		.disable_val = DISABLE_VAL(RK817_ID_DCDC3),
+		.of_map_mode = rk8xx_regulator_of_map_mode,
+		.owner = THIS_MODULE,
+	}, {
+		.name = "DCDC_REG4",
+		.supply_name = "vcc4",
+		.of_match = of_match_ptr("DCDC_REG4"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = RK817_ID_DCDC4,
+		.ops = &rk817_buck_ops_range,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = RK817_BUCK3_SEL_CNT + 1,
+		.linear_ranges = rk817_buck3_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(rk817_buck3_voltage_ranges),
+		.vsel_reg = RK817_BUCK4_ON_VSEL_REG,
+		.vsel_mask = RK817_BUCK_VSEL_MASK,
+		.enable_reg = RK817_POWER_EN_REG(0),
+		.enable_mask = ENABLE_MASK(RK817_ID_DCDC4),
+		.enable_val = ENABLE_MASK(RK817_ID_DCDC4),
+		.disable_val = DISABLE_VAL(RK817_ID_DCDC4),
+		.of_map_mode = rk8xx_regulator_of_map_mode,
+		.owner = THIS_MODULE,
+	},
+	RK817_DESC(RK817_ID_LDO1, "LDO_REG1", "vcc5", 600, 3400, 25,
+		   RK817_LDO_ON_VSEL_REG(0), RK817_LDO_VSEL_MASK,
+		   RK817_POWER_EN_REG(1), ENABLE_MASK(0), ENABLE_MASK(0),
+		   DISABLE_VAL(0), 400),
+	RK817_DESC(RK817_ID_LDO2, "LDO_REG2", "vcc5", 600, 3400, 25,
+		   RK817_LDO_ON_VSEL_REG(1), RK817_LDO_VSEL_MASK,
+		   RK817_POWER_EN_REG(1), ENABLE_MASK(1), ENABLE_MASK(1),
+		   DISABLE_VAL(1), 400),
+	RK817_DESC(RK817_ID_LDO3, "LDO_REG3", "vcc5", 600, 3400, 25,
+		   RK817_LDO_ON_VSEL_REG(2), RK817_LDO_VSEL_MASK,
+		   RK817_POWER_EN_REG(1), ENABLE_MASK(2), ENABLE_MASK(2),
+		   DISABLE_VAL(2), 400),
+	RK817_DESC(RK817_ID_LDO4, "LDO_REG4", "vcc6", 600, 3400, 25,
+		   RK817_LDO_ON_VSEL_REG(3), RK817_LDO_VSEL_MASK,
+		   RK817_POWER_EN_REG(1), ENABLE_MASK(3), ENABLE_MASK(3),
+		   DISABLE_VAL(3), 400),
+	RK817_DESC(RK817_ID_LDO5, "LDO_REG5", "vcc6", 600, 3400, 25,
+		   RK817_LDO_ON_VSEL_REG(4), RK817_LDO_VSEL_MASK,
+		   RK817_POWER_EN_REG(2), ENABLE_MASK(0), ENABLE_MASK(0),
+		   DISABLE_VAL(0), 400),
+	RK817_DESC(RK817_ID_LDO6, "LDO_REG6", "vcc6", 600, 3400, 25,
+		   RK817_LDO_ON_VSEL_REG(5), RK817_LDO_VSEL_MASK,
+		   RK817_POWER_EN_REG(2), ENABLE_MASK(1), ENABLE_MASK(1),
+		   DISABLE_VAL(1), 400),
+	RK817_DESC(RK817_ID_LDO7, "LDO_REG7", "vcc7", 600, 3400, 25,
+		   RK817_LDO_ON_VSEL_REG(6), RK817_LDO_VSEL_MASK,
+		   RK817_POWER_EN_REG(2), ENABLE_MASK(2), ENABLE_MASK(2),
+		   DISABLE_VAL(2), 400),
+	RK817_DESC(RK817_ID_LDO8, "LDO_REG8", "vcc7", 600, 3400, 25,
+		   RK817_LDO_ON_VSEL_REG(7), RK817_LDO_VSEL_MASK,
+		   RK817_POWER_EN_REG(2), ENABLE_MASK(3), ENABLE_MASK(3),
+		   DISABLE_VAL(3), 400),
+	RK817_DESC(RK817_ID_LDO9, "LDO_REG9", "vcc7", 600, 3400, 25,
+		   RK817_LDO_ON_VSEL_REG(8), RK817_LDO_VSEL_MASK,
+		   RK817_POWER_EN_REG(3), ENABLE_MASK(0), ENABLE_MASK(0),
+		   DISABLE_VAL(0), 400),
+	RK817_BOOST_DESC(RK817_ID_BOOST, "BOOST", "vcc8", 4700, 5400, 100,
+			 RK817_BOOST_OTG_CFG, RK817_BOOST_VSEL_MASK,
+			 RK817_POWER_EN_REG(3), ENABLE_MASK(1), ENABLE_MASK(1),
+		   DISABLE_VAL(1), 400, 3500 - 5400),
+	RK817_DESC_SWITCH(RK817_ID_BOOST_OTG_SW, "OTG_SWITCH", "vcc9",
+			  RK817_POWER_EN_REG(3), ENABLE_MASK(2),
+			  ENABLE_MASK(2), DISABLE_VAL(2)),
+};
+
 static const struct regulator_desc rk818_reg[] = {
 	{
 		.name = "DCDC_REG1",
@@ -759,6 +1381,14 @@ static int rk808_regulator_probe(struct platform_device *pdev)
 		regulators = rk808_reg;
 		nregulators = RK808_NUM_REGULATORS;
 		break;
+	case RK809_ID:
+		regulators = rk809_reg;
+		nregulators = RK809_NUM_REGULATORS;
+		break;
+	case RK817_ID:
+		regulators = rk817_reg;
+		nregulators = RK817_NUM_REGULATORS;
+		break;
 	case RK818_ID:
 		regulators = rk818_reg;
 		nregulators = RK818_NUM_REGULATORS;
@@ -797,6 +1427,7 @@ static int rk808_regulator_probe(struct platform_device *pdev)
 module_platform_driver(rk808_regulator_driver);
 
 MODULE_DESCRIPTION("regulator driver for the RK808/RK818 series PMICs");
+MODULE_AUTHOR("Tony xie <tony.xie@xxxxxxxxxxxxxx>");
 MODULE_AUTHOR("Chris Zhong <zyw@xxxxxxxxxxxxxx>");
 MODULE_AUTHOR("Zhang Qing <zhangqing@xxxxxxxxxxxxxx>");
 MODULE_AUTHOR("Wadim Egorov <w.egorov@xxxxxxxxx>");
diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h
index b973b0a..b4ce2373 100644
--- a/include/linux/mfd/rk808.h
+++ b/include/linux/mfd/rk808.h
@@ -396,7 +396,10 @@ enum rk805_reg {
 #define SHUTDOWN_FUN			(0x2 << 2)
 #define SLEEP_FUN			(0x1 << 2)
 #define RK8XX_ID_MSK			0xfff0
+#define PWM_MODE_MSK			BIT(7)
 #define FPWM_MODE			BIT(7)
+#define AUTO_PWM_MODE			0
+
 enum rk817_reg_id {
 	RK817_ID_DCDC1 = 0,
 	RK817_ID_DCDC2,
-- 
1.9.1


--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux