On Wed, 25 Jul 2018 10:08:46 +0300
Mikko Perttunen <cyndis@xxxxxxxx> wrote:
> On 24.07.2018 17:34, Aapo Vienamo wrote:
> > Configure the voltage reference used by the automatic pad drive strength
> > calibration procedure. The value is a magic number from the TRM.
> >
> > Signed-off-by: Aapo Vienamo <avienamo@xxxxxxxxxx>
> > ---
> > drivers/mmc/host/sdhci-tegra.c | 14 ++++++++++++--
> > 1 file changed, 12 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
> > index e40ca43..6008e2f 100644
> > --- a/drivers/mmc/host/sdhci-tegra.c
> > +++ b/drivers/mmc/host/sdhci-tegra.c
> > @@ -49,6 +49,10 @@
> > #define SDHCI_AUTO_CAL_START BIT(31)
> > #define SDHCI_AUTO_CAL_ENABLE BIT(29)
> >
> > +#define SDHCI_TEGRA_SDMEM_COMP_PADCTRL 0x1e0
> > +#define SDHCI_TEGRA_SDMEM_COMP_PADCTRL_VREF_SEL_MASK 0x0000000f
> > +#define SDHCI_TEGRA_SDMEM_COMP_PADCTRL_VREF_SEL_VAL 0x7
> > +
> > #define SDHCI_TEGRA_AUTO_CAL_STATUS 0x1ec
> > #define SDHCI_TEGRA_AUTO_CAL_ACTIVE BIT(31)
> >
> > @@ -152,7 +156,7 @@ static void tegra_sdhci_reset(struct sdhci_host *host, u8 mask)
> > struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> > struct sdhci_tegra *tegra_host = sdhci_pltfm_priv(pltfm_host);
> > const struct sdhci_tegra_soc_data *soc_data = tegra_host->soc_data;
> > - u32 misc_ctrl, clk_ctrl;
> > + u32 misc_ctrl, clk_ctrl, pad_ctrl;
> >
> > sdhci_reset(host, mask);
> >
> > @@ -193,8 +197,14 @@ static void tegra_sdhci_reset(struct sdhci_host *host, u8 mask)
> > sdhci_writel(host, misc_ctrl, SDHCI_TEGRA_VENDOR_MISC_CTRL);
> > sdhci_writel(host, clk_ctrl, SDHCI_TEGRA_VENDOR_CLOCK_CTRL);
> >
> > - if (soc_data->nvquirks & NVQUIRK_HAS_PADCALIB)
> > + if (soc_data->nvquirks & NVQUIRK_HAS_PADCALIB) {
> > + pad_ctrl = sdhci_readl(host, SDHCI_TEGRA_SDMEM_COMP_PADCTRL);
> > + pad_ctrl &= ~SDHCI_TEGRA_SDMEM_COMP_PADCTRL_VREF_SEL_MASK;
> > + pad_ctrl |= SDHCI_TEGRA_SDMEM_COMP_PADCTRL_VREF_SEL_VAL;
> > + sdhci_writel(host, pad_ctrl, SDHCI_TEGRA_SDMEM_COMP_PADCTRL);
> > +
>
> Will this happen to only eMMC controllers or for all controllers? My
> docs are saying this should be set to 0x7 for SDMMC2/4 and 0x1 or 0x2
> for SDMMC1/3 depending on voltage. Not sure how downstream is
> programming it, though.
The Tegra210 TRM specifies that VREF_SEL should be set 0x7 for all of
the controllers, there's no mention of this depending on the mode. The
same value is also programmed by the downstream kernels for Tegra210
and Tegra186.
-Aapo
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
