Re: [PATCH v0] arm64: dts: rockchip: add support for ROC-RK3399-PC board

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Levin,

Missatge de Heiko Stuebner <heiko@xxxxxxxxx> del dia dt., 24 de jul.
2018 a les 11:29:
>
> Hi Levin,
>
> Am Samstag, 21. Juli 2018, 10:30:26 CEST schrieb djw@xxxxxxxxxxxxx:
> > From: Levin Du <djw@xxxxxxxxxxxxx>
> >
> > ROC-RK3399-PC is the first power efficient 4GB DDR4 single board
>
> maybe "is a power efficient" instead of "the first" ;-)
>
> [...]
>
> > diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts
> > new file mode 100644
> > index 0000000..207f2e3
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts
> > @@ -0,0 +1,717 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +/*
> > + * Copyright (c) 2017 T-Chip Intelligent Technology Co., Ltd
> > + */
> > +
> > +/dts-v1/;
> > +#include <dt-bindings/pwm/pwm.h>
> > +#include "rk3399.dtsi"
> > +#include "rk3399-opp.dtsi"
> > +
> > +/ {
> > +     model = "Firefly ROC-RK3399-PC Board";
> > +     compatible = "firefly,roc-rk3399-pc", "rockchip,rk3399";
> > +
> > +     chosen {
> > +             bootargs = "earlycon=uart8250,mmio32,0xff1a0000 swiotlb=1";
>
> I don't think we want to hard-code linux bootargs in the generic devicetree
>
> > +             stdout-path = "serial2:1500000n8";
> > +     };
> > +
> > +     backlight: backlight {
> > +             compatible = "pwm-backlight";
> > +             enable-gpios = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
> > +             pwms = <&pwm0 0 25000 0>;
> > +             brightness-levels = <
> > +                       0   1   2   3   4   5   6   7
>
> As Rob noted in the px30 evb patch, there is now a property helping
> to drop these long lists of brightness levels, see
> https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=1e5e7cc794b5a332c23216dade0a2e937d694b7f

Adding to the Heiko information. Did you try to just remove brightness-levels?
Without this property, the driver computes a default table with the
brightness levels filled with the numbers provided by the CIE 1931
algorithm. That algorithm is used to dim a led for human perception.

Note that the patches needed did not land yet, are in linux-next, and
you will also be interested in apply this patch [1].

[1] https://lkml.org/lkml/2018/7/24/116

>
>
> > +                       8   9  10  11  12  13  14  15
> > +                      16  17  18  19  20  21  22  23
> > +                      24  25  26  27  28  29  30  31
> > +                      32  33  34  35  36  37  38  39
> > +                      40  41  42  43  44  45  46  47
> > +                      48  49  50  51  52  53  54  55
> > +                      56  57  58  59  60  61  62  63
> > +                      64  65  66  67  68  69  70  71
> > +                      72  73  74  75  76  77  78  79
> > +                      80  81  82  83  84  85  86  87
> > +                      88  89  90  91  92  93  94  95
> > +                      96  97  98  99 100 101 102 103
> > +                     104 105 106 107 108 109 110 111
> > +                     112 113 114 115 116 117 118 119
> > +                     120 121 122 123 124 125 126 127
> > +                     128 129 130 131 132 133 134 135
> > +                     136 137 138 139 140 141 142 143
> > +                     144 145 146 147 148 149 150 151
> > +                     152 153 154 155 156 157 158 159
> > +                     160 161 162 163 164 165 166 167
> > +                     168 169 170 171 172 173 174 175
> > +                     176 177 178 179 180 181 182 183
> > +                     184 185 186 187 188 189 190 191
> > +                     192 193 194 195 196 197 198 199
> > +                     200 201 202 203 204 205 206 207
> > +                     208 209 210 211 212 213 214 215
> > +                     216 217 218 219 220 221 222 223
> > +                     224 225 226 227 228 229 230 231
> > +                     232 233 234 235 236 237 238 239
> > +                     240 241 242 243 244 245 246 247
> > +                     248 249 250 251 252 253 254 255>;
> > +             default-brightness-level = <200>;
> > +     };
>
> [...]
>
> > +     vcc_vbus_typec0: vcc-vbus-typec0 {
> > +             compatible = "regulator-fixed";
> > +             regulator-name = "vcc_vbus_typec0";
> > +             regulator-always-on;
> > +             regulator-boot-on;
> > +             regulator-min-microvolt = <5000000>;
> > +             regulator-max-microvolt = <5000000>;
> > +     };
> > +
> > +     vcc12v_sys: mp8859-dcdc1 {
>
> The mp8859 seems to be an i2c-device, as also shown by the
> nearly empty mp8859 entry below, so shouldn't this regulator
> be defined there?
>
>
> > +             compatible = "regulator-fixed";
> > +             regulator-name = "vcc12v_sys";
> > +             regulator-always-on;
> > +             regulator-boot-on;
> > +             regulator-min-microvolt = <12000000>;
> > +             regulator-max-microvolt = <12000000>;
> > +             vin-supply = <&vcc_vbus_typec0>;
> > +     };
>
> [...]
>
> > +     vcc_hub_en: vcc_hub_en-regulator {
> > +             compatible = "regulator-fixed";
> > +             enable-active-high;
> > +             gpio = <&gpio2 RK_PA4 GPIO_ACTIVE_HIGH>;
> > +             pinctrl-names = "default";
> > +             pinctrl-0 = <&hub_rst>;
> > +             regulator-name = "vcc_hub_en";
> > +             regulator-always-on;
>
> missing vin-supply
>
> > +     };
> > +
>
> [...]
>
> > +     vdd_cpu_b: regulator@40 {
> > +             compatible = "silergy,syr827";
> > +             reg = <0x40>;
> > +             fcs,suspend-voltage-selector = <1>;
> > +             pinctrl-names = "default";
> > +             pinctrl-0 = <&vsel1_gpio>;
> > +             regulator-name = "vdd_cpu_b";
> > +             regulator-min-microvolt = <712500>;
> > +             regulator-max-microvolt = <1500000>;
> > +             regulator-ramp-delay = <1000>;
> > +             regulator-always-on;
> > +             regulator-boot-on;
> > +             vsel-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>;
>
> vsel-gpios is not defined in the mainline dt-binding of the fan5355/syr82*
>
> > +             vin-supply = <&vcc3v3_sys>;
> > +
> > +             regulator-state-mem {
> > +                     regulator-off-in-suspend;
> > +             };
> > +     };
> > +
> > +     vdd_gpu: regulator@41 {
> > +             compatible = "silergy,syr828";
> > +             reg = <0x41>;
> > +             fcs,suspend-voltage-selector = <1>;
> > +             pinctrl-names = "default";
> > +             pinctrl-0 = <&vsel2_gpio>;
> > +             regulator-name = "vdd_gpu";
> > +             regulator-min-microvolt = <712500>;
> > +             regulator-max-microvolt = <1500000>;
> > +             regulator-ramp-delay = <1000>;
> > +             regulator-always-on;
> > +             regulator-boot-on;
> > +             vsel-gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
>
> same as above
>
> > +             vin-supply = <&vcc3v3_sys>;
> > +
> > +             regulator-state-mem {
> > +                     regulator-off-in-suspend;
> > +             };
> > +     };
> > +};
> > +
> > +&i2c1 {
> > +     i2c-scl-rising-time-ns = <300>;
> > +     i2c-scl-falling-time-ns = <15>;
> > +     status = "okay";
> > +};
> > +
> > +&i2c3 {
> > +     i2c-scl-rising-time-ns = <450>;
> > +     i2c-scl-falling-time-ns = <15>;
> > +     status = "okay";
> > +};
> > +
> > +&i2c4 {
> > +     i2c-scl-rising-time-ns = <600>;
> > +     i2c-scl-falling-time-ns = <20>;
> > +     status = "okay";
> > +
> > +     mp8859: mp8859@66 {
> > +             compatible = "mps,mp8859";
>
> missing a dt-binding and also a real regulator implementation?
>
> > +             reg = <0x66>;
> > +     };
> > +
> > +     fusb1: usb-typec@22 {
> > +             compatible = "fcs,fusb302";
> > +             reg = <0x22>;
> > +             pinctrl-names = "default";
> > +             pinctrl-0 = <&fusb1_int>;
> > +             fcs,int-n = <&gpio1 RK_PA1 GPIO_ACTIVE_HIGH>;
>
> mainline binding expects an "interrupts" property not the
> fcs,int-n from above
>
> > +             status = "okay";
> > +     };
> > +
> > +};
> > +
> > +&i2c7 {
> > +     i2c-scl-rising-time-ns = <600>;
> > +     i2c-scl-falling-time-ns = <20>;
> > +     status = "okay";
> > +
> > +     fusb0: usb-typec@22 {
> > +             compatible = "fcs,fusb302";
> > +             reg = <0x22>;
> > +             pinctrl-names = "default";
> > +             pinctrl-0 = <&fusb0_int>;
> > +             fcs,int-n = <&gpio1 RK_PA2 GPIO_ACTIVE_HIGH>;
>
> same as above
>
> > +             status = "okay";
> > +     };
> > +};
> > +
> > +&i2s0 {
> > +     rockchip,playback-channels = <8>;
> > +     rockchip,capture-channels = <8>;
> > +     #sound-dai-cells = <0>;
>
> sound-dai-cells are in rk3399.dtsi now ... see
> https://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc.git/commit/?id=4486baca66e7a96a6ded3957cb522872a49870ce
>
> > +     status = "okay";
> > +};
> > +
> > +&i2s1 {
> > +     rockchip,playback-channels = <2>;
> > +     rockchip,capture-channels = <2>;
> > +     #sound-dai-cells = <0>;
>
> same as above
>
> > +     status = "okay";
> > +};
> > +
> > +&i2s2 {
> > +     #sound-dai-cells = <0>;
>
> same as above
>
> > +     status = "okay";
> > +};
> > +
>
> > +&tcphy0 {
> > +     extcon = <&fusb0>;
>
> the extcon is not described in the mainline fusb302 binding.
>
> > +     status = "okay";
> > +};
> > +
> > +&tcphy1 {
> > +     extcon = <&fusb1>;
>
> same as above
>
> > +     status = "okay";
> > +};
> > +
> > +&tsadc {
> > +     /* tshut mode 0:CRU 1:GPIO */
> > +     rockchip,hw-tshut-mode = <1>;
> > +     /* tshut polarity 0:LOW 1:HIGH */
> > +     rockchip,hw-tshut-polarity = <1>;
> > +     status = "okay";
> > +};
> > +
> > +&u2phy0 {
> > +     status = "okay";
> > +
> > +     u2phy0_otg: otg-port {
> > +             phy-supply = <&vcc5v0_host>;
> > +             //status = "disabled";
>
> don't leave commented stuff in the dt please.
>
> > +             status = "okay";
> > +     };
> > +
> > +     u2phy0_host: host-port {
> > +             phy-supply = <&vcc5v0_host>;
> > +             status = "okay";
> > +     };
> > +};
> > +
> > +&u2phy1 {
> > +     status = "okay";
> > +
> > +     u2phy1_otg: otg-port {
> > +             phy-supply = <&vcc5v0_host>;
> > +             //status = "disabled";
>
> same as above
>
> > +             status = "okay";
> > +     };
> > +
> > +     u2phy1_host: host-port {
> > +             phy-supply = <&vcc5v0_host>;
> > +             status = "okay";
> > +     };
> > +};
>
>
> Thanks
> Heiko
>

Best regards,
 Enric

>
>
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux