Hi Boris:
see my comments, thanks for the quick response
On 07/19/18 17:57, Boris Brezillon wrote:
> On Thu, 19 Jul 2018 17:46:11 +0800
> Yixun Lan <yixun.lan@xxxxxxxxxxx> wrote:
>
>> From: Liang Yang <liang.yang@xxxxxxxxxxx>
>>
>> Add Amlogic NAND controller dt-bindings for Meson SoC,
>> Current this driver support GXBB/GXL/AXG platform.
>>
>> Signed-off-by: Liang Yang <liang.yang@xxxxxxxxxxx>
>> Signed-off-by: Yixun Lan <yixun.lan@xxxxxxxxxxx>
>> ---
>> .../bindings/mtd/amlogic,meson-nand.txt | 95 +++++++++++++++++++
>> 1 file changed, 95 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt
>>
>> diff --git a/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt
>> new file mode 100644
>> index 000000000000..31f910dcd27a
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt
>> @@ -0,0 +1,95 @@
>> +Amlogic NAND Flash Controller (NFC) for GXBB/GXL/AXG family SoCs
>> +
>> +This file documents the properties in addition to those available in
>> +the MTD NAND bindings.
>> +
>> +Required properties:
>> +- compatible : contains one of:
>> + - "amlogic,meson-gxl-nfc"
>> + - "amlogic,meson-axg-nfc"
>> +- clocks :
>> + A list of phandle + clock-specifier pairs for the clocks listed
>> + in clock-names.
>> +
>> +- clock-names: Should contain the following:
>> + "core" - NFC module gate clock
>> + "device" - device clock from eMMC sub clock controller
>> +
>> +- pins : Select pins which NFC need.
>> +- nand_pins: Detail NAND pins information.
>
> You should document pinctrl-0 and pinctrl-names, not pins and nand_pins.
>
Ok, will fix this
>> +- amlogic,mmc-syscon : Required for NAND clocks, it's shared with SD/eMMC
>> + controller port C
>
> Are you sure this is still needed, even after exposing MMC/NAND clks
> through the CCF?
>
yes, the SD_EMMC_CLOCK register from eMMC space explore a few other bit
that not fit well into clock model, thus we still need to access them
from NAND driver, we know it's kind of ugly..
#define SD_EMMC_CLOCK 0x00
#define CLK_ALWAYS_ON BIT(28)
#define CLK_SELECT_NAND BIT(31)
#define CLK_DIV_MASK GENMASK(5, 0)
we probably could get rid of CLK_DIV_MASK, but need to keep other two
> You forgot
> - #address-cells
> - #size-cells
> - reg
> - interrupts
> -
>
will fix these
>> +
>> +Optional children nodes:
>> +Children nodes represent the available nand chips.
>> +
>> +Optional properties:
>> +- amlogic,nand-enable-scrambler: enable the NAND scrambler feature.
>> + - (absent) = scrambler is disabled
>> + - (present) = scrambler is enabled
>
> I keep thinking this is not needed if you have the NAND chip properly
> defined (NAND_NEED_SCRAMBLING flag set in chip->options).
>
Ok, we will try this flag
>> +
>> +
>> +Other properties:
>> +see Documentation/devicetree/bindings/mtd/nand.txt for generic bindings.
>> +
>> +Example demonstrate on AXG SoC:
>> +
>> + sd_emmc_c_clkc: mmc@7000 {
>> + compatible = "amlogic,meson-axg-mmc-clkc", "syscon";
>> + reg = <0x0 0x7000 0x0 0x800>;
>> + status = "okay";
>> + };
>> +
>> + nand: nfc@7800 {
>> + compatible = "amlogic,meson-axg-nfc";
>> + reg = <0x0 0x7800 0x0 0x100>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interrupts = <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>;
>> + status = "disabled";
>> +
>> + clocks = <&clkc CLKID_SD_EMMC_C>,
>> + <&sd_emmc_c_clkc CLKID_MMC_DIV>;
>> + clock-names = "core", "device";
>> + amlogic,mmc-syscon = <&sd_emmc_c_clkc>;
>> +
>> + status = "okay";
>> +
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&nand_pins>;
>> +
>> + nand@0 {
>> + reg = <0>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> +
>> + nand-on-flash-bbt;
>> + nand-ecc-mode = "hw";
>> + nand-ecc-strength = <8>;
>> + nand-ecc-step-size = <1024>;
>
> I'd recommend not forcing a specific ECC config in the example.
>
Ok, will fix
>> +
>> + amlogic,nand-enable-scrambler;
>> +
>> + partition@0 {
>> + label = "boot";
>> + reg = <0x00000000 0x00200000>;
>> + read-only;
>> + };
>
> Blank line here.
will fix
>
>> + partition@200000 {
>> + label = "env";
>> + reg = <0x00200000 0x00400000>;
>> + };
>> + partition@600000 {
>> + label = "system";
>> + reg = <0x00600000 0x00a00000>;
>> + };
>> + partition@1000000 {
>> + label = "rootfs";
>> + reg = <0x01000000 0x03000000>;
>> + };
>> + partition@4000000 {
>> + label = "media";
>> + reg = <0x04000000 0x8000000>;
>> + };
>> + };
>> + };
>
> .
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
