Hi,
On Thu, Jul 5, 2018 at 2:46 PM, Girish Mahadevan <girishm@xxxxxxxxxxxxxx> wrote:
> Signed-off-by: Girish Mahadevan <girishm@xxxxxxxxxxxxxx>
> ---
> .../devicetree/bindings/spi/qcom,spi-qcom-qspi.txt | 36 ++++++++++++++++++++++
> err.txt | 27 ----------------
> 2 files changed, 36 insertions(+), 27 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt
> delete mode 100644 err.txt
>
> diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt
> new file mode 100644
> index 0000000..3baa893
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt
> @@ -0,0 +1,36 @@
> +QTI [Qualcomm Technologies Inc] Quad Serial Peripheral Interface (QSPI)
> +
> +QSPI [Quad Serial Peripheral Interface] allows single dual and quad read/write
> +access to slaves. QTI's QSPI controller implements the QSPI protocol to interface
> +with slaves like NOR Flash devices.
> +
> +Required properties:
> +- compatible: Should contain:
> + "qcom,qspi-v1"
> +- reg: Contains the base register location and length
> +- interrupts: Interrupt number used by the controller.
> +- clocks: Contains the core and AHB clock names.
> +- clock-names: "core" for core clock and "iface" for AHB clock.
> +- spi-max-frequency: Maximum SPI core clock frequency in Hz.
> +
> +SPI slave nodes must be children of the SPI master node and can contain
> +properties described in Documentation/devicetree/bindings/spi/spi-bus.txt
> +
> +Example:
> +
> + qspi: qspi@7418000 {
> + compatible = "qcom,qspi-v1";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x7418000 0x600>;
> + interrupts = <0 459 0>;
Please use a more proper interrupts example, AKA:
interrupts = <GIC_SPI 459 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "iface", "core";
> + clocks = <&clock_gcc clk_gcc_qspi_ahb_clk>,
> + <&clock_gcc clk_gcc_qspi_ser_clk>;
In upstream I believe that the clock #defines are usually in ALL CAPS.
Maybe good to use that in your example. In the clock patches I'm
hoping to send up for SDM845, for instance, this will be:
clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
<&gcc GCC_QSPI_CORE_CLK>;
> +
> + device@0 {
> + compatible = "dummy_device";
> + reg = <x>; /* CS for the device */
> + spi-max-frequency = <f>; /* Max supported frequency of the slave (Hz) */
Since you are a Quad SPI controller, maybe you'd want your example to
include how to enable that? AKA:
spi-tx-bus-width = <4>;
spi-rx-bus-width = <4>;
-Doug
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
