From: Jeykumar Sankaran <jsanka@xxxxxxxxxxxxxx>
Adds bindings for Snapdragon 845 display processing unit
Changes in v2:
- Use SoC specific compatibles for mdss and dpu
- Use assigned-clocks to set initial clock frequency
Signed-off-by: Jeykumar Sankaran <jsanka@xxxxxxxxxxxxxx>
Signed-off-by: Rajesh Yadav <ryadav@xxxxxxxxxxxxxx>
Signed-off-by: Sean Paul <seanpaul@xxxxxxxxxxxx>
---
.../devicetree/bindings/display/msm/dpu.txt | 136 ++++++++++++++++++
1 file changed, 136 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/msm/dpu.txt
diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt b/Documentation/devicetree/bindings/display/msm/dpu.txt
new file mode 100644
index 000000000000..a998028896ba
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/msm/dpu.txt
@@ -0,0 +1,136 @@
+Qualcomm Technologies, Inc. DPU KMS
+
+Description:
+
+Device tree bindings for MSM Mobile Display Subsytem(MDSS) that encapsulates
+sub-blocks like DPU display controller, DSI and DP interfaces etc.
+The DPU display controller is found in SDM845 SoC.
+
+MDSS:
+Required properties:
+- compatible: "qcom,sdm845-mdss"
+- reg: physical base address and length of contoller's registers.
+- reg-names: register region names. The following region is required:
+ * "mdss_phys"
+- power-domains: a power domain consumer specifier according to
+ Documentation/devicetree/bindings/power/power_domain.txt
+- clocks: list of phandles for clock device nodes needed by the device.
+- clock-names: device clock names, must be in same order as clocks property.
+ The following clocks are required:
+ * "iface"
+ * "bus"
+ * "core"
+- interrupts: interrupt signal from MDSS.
+- interrupt-controller: identifies the node as an interrupt controller.
+- #interrupt-cells: specifies the number of cells needed to encode an interrupt
+ source, should be 1.
+- iommus: phandle of iommu device node.
+- #address-cells: number of address cells for the MDSS children. Should be 1.
+- #size-cells: Should be 1.
+- ranges: parent bus address space is the same as the child bus address space.
+
+Optional properties:
+- assigned-clocks: list of phandles for clock device nodes needing rate
+ assignment
+- assigned-clock-rates: list of clock frequencies sorted in the same order as
+ the assigned-clocks property.
+
+MDP:
+Required properties:
+- compatible: "qcom,sdm845-dpu"
+- reg: physical base address and length of controller's registers.
+- reg-names : register region names. The following region is required:
+ * "mdp_phys"
+ * "vbif_phys"
+- clocks: list of phandles for clock device nodes needed by the device.
+- clock-names: device clock names, must be in same order as clocks property.
+ The following clocks are required.
+ * "bus"
+ * "iface"
+ * "core"
+ * "vsync"
+- interrupt-parent: phandle to MDSS block.
+- interrupts: interrupt line from DPU to MDSS.
+- ports: contains the list of output ports from DPU device. These ports connect
+ to interfaces that are external to the DPU hardware, such as DSI, DP etc.
+
+ Each output port contains an endpoint that describes how it is connected to an
+ external interface. These are described by the standard properties documented
+ here:
+ Documentation/devicetree/bindings/graph.txt
+ Documentation/devicetree/bindings/media/video-interfaces.txt
+
+ Port 0 -> DPU_INTF1 (DSI1)
+ Port 1 -> DPU_INTF2 (DSI2)
+
+Optional properties:
+- assigned-clocks: list of phandles for clock device nodes needing rate
+ assignment
+- assigned-clock-rates: list of clock frequencies sorted in the same order as
+ the assigned-clocks property.
+
+Example:
+
+ mdss: mdss@ae00000 {
+ compatible = "qcom,sdm845-mdss";
+ reg = <0xae00000 0x1000>;
+ reg-names = "mdss_phys";
+
+ power-domains = <&clock_dispcc 0>;
+
+ clocks = <&gcc GCC_DISP_AHB_CLK>, <&gcc GCC_DISP_AXI_CLK>,
+ <&clock_dispcc DISP_CC_MDSS_MDP_CLK>;
+ clock-names = "iface", "bus", "core";
+
+ assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>;
+ assigned-clock-rates = <300000000>;
+
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ iommus = <&apps_iommu 0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mdss_mdp: mdp@ae01000 {
+ compatible = "qcom,sdm845-dpu";
+ reg = <0x0ae01000 0x8f000>,
+ <0x0aeb0000 0x2008>;
+ reg-names = "mdp_phys", "vbif_phys";
+
+ clocks = <&clock_dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&clock_dispcc DISP_CC_MDSS_AXI_CLK>,
+ <&clock_dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ clock-names = "iface", "bus", "core", "vsync";
+
+ assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ assigned-clock-rates = <0 0 300000000 19200000>;
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dpu_intf1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dpu_intf2_out: endpoint {
+ remote-endpoint = <&dsi1_in>;
+ };
+ };
+ };
+ };
+ };
--
Sean Paul, Software Engineer, Google / Chromium OS
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
