The OCC is a device embedded on a POWER processor that collects and
aggregates sensor data from the processor and system. The OCC can
provide the raw sensor data as well as perform thermal and power
management on the system.
This driver provides an atomic communications channel between a service
processor (e.g. a BMC) and the OCC. The driver is dependent on the FSI
SBEFIFO driver to get hardware access through the SBE to the OCC SRAM.
Commands are issued to the SBE to send or fetch data to the SRAM.
Signed-off-by: Eddie James <eajames@xxxxxxxxxxxxxxxxxx>
Signed-off-by: Andrew Jeffery <andrew@xxxxxxxx>
Signed-off-by: Benjamin Herrenschmidt <benh@xxxxxxxxxxxxxxxxxxx>
Signed-off-by: Joel Stanley <joel@xxxxxxxxx>
---
drivers/fsi/Kconfig | 10 +
drivers/fsi/Makefile | 1 +
drivers/fsi/fsi-occ.c | 609 ++++++++++++++++++++++++++++++++++++++++++++++++
include/linux/fsi-occ.h | 34 +++
4 files changed, 654 insertions(+)
create mode 100644 drivers/fsi/fsi-occ.c
create mode 100644 include/linux/fsi-occ.h
diff --git a/drivers/fsi/Kconfig b/drivers/fsi/Kconfig
index 24f84a9..322cec3 100644
--- a/drivers/fsi/Kconfig
+++ b/drivers/fsi/Kconfig
@@ -39,4 +39,14 @@ config FSI_SBEFIFO
a pipe-like FSI device for communicating with the self boot engine
(SBE) on POWER processors.
+config FSI_OCC
+ tristate "OCC SBEFIFO client device driver"
+ depends on FSI_SBEFIFO
+ ---help---
+ This option enables an SBEFIFO based On-Chip Controller (OCC) device
+ driver. The OCC is a device embedded on a POWER processor that collects
+ and aggregates sensor data from the processor and system. The OCC can
+ provide the raw sensor data as well as perform thermal and power
+ management on the system.
+
endif
diff --git a/drivers/fsi/Makefile b/drivers/fsi/Makefile
index 851182e..75fdc6d 100644
--- a/drivers/fsi/Makefile
+++ b/drivers/fsi/Makefile
@@ -4,3 +4,4 @@ obj-$(CONFIG_FSI_MASTER_HUB) += fsi-master-hub.o
obj-$(CONFIG_FSI_MASTER_GPIO) += fsi-master-gpio.o
obj-$(CONFIG_FSI_SCOM) += fsi-scom.o
obj-$(CONFIG_FSI_SBEFIFO) += fsi-sbefifo.o
+obj-$(CONFIG_FSI_OCC) += fsi-occ.o
diff --git a/drivers/fsi/fsi-occ.c b/drivers/fsi/fsi-occ.c
new file mode 100644
index 0000000..bba67a6
--- /dev/null
+++ b/drivers/fsi/fsi-occ.c
@@ -0,0 +1,609 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * On-Chip Controller Driver
+ *
+ * Copyright (C) IBM Corporation 2018
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <asm/unaligned.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/fs.h>
+#include <linux/fsi-sbefifo.h>
+#include <linux/gfp.h>
+#include <linux/idr.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/miscdevice.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/fsi-occ.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/uaccess.h>
+
+#define OCC_SRAM_BYTES 4096
+#define OCC_CMD_DATA_BYTES 4090
+#define OCC_RESP_DATA_BYTES 4089
+
+#define OCC_SRAM_CMD_ADDR 0xFFFBE000
+#define OCC_SRAM_RSP_ADDR 0xFFFBF000
+
+/*
+ * Assume we don't have much FFDC, if we do we'll overflow and
+ * fail the command. This needs to be big enough for simple
+ * commands as well.
+ */
+#define OCC_SBE_STATUS_WORDS 32
+
+#define OCC_TIMEOUT_MS 1000
+#define OCC_CMD_IN_PRG_WAIT_MS 50
+
+struct occ {
+ struct device *dev;
+ struct device *sbefifo;
+ char name[32];
+ int idx;
+ struct miscdevice mdev;
+ struct mutex occ_lock;
+};
+
+#define to_occ(x) container_of((x), struct occ, mdev)
+
+struct occ_response {
+ u8 seq_no;
+ u8 cmd_type;
+ u8 return_status;
+ __be16 data_length;
+ u8 data[OCC_RESP_DATA_BYTES + 2]; /* two bytes checksum */
+} __packed;
+
+struct occ_client {
+ struct occ *occ;
+ struct mutex lock;
+ size_t data_size;
+ size_t read_offset;
+ u8 *buffer;
+};
+
+#define to_client(x) container_of((x), struct occ_client, xfr)
+
+static DEFINE_IDA(occ_ida);
+
+static int occ_open(struct inode *inode, struct file *file)
+{
+ struct occ_client *client = kzalloc(sizeof(*client), GFP_KERNEL);
+ struct miscdevice *mdev = file->private_data;
+ struct occ *occ = to_occ(mdev);
+
+ if (!client)
+ return -ENOMEM;
+
+ client->buffer = (u8 *)__get_free_page(GFP_KERNEL);
+ if (!client->buffer) {
+ kfree(client);
+ return -ENOMEM;
+ }
+
+ client->occ = occ;
+ mutex_init(&client->lock);
+ file->private_data = client;
+
+ /* We allocate a 1-page buffer, make sure it all fits */
+ BUILD_BUG_ON((OCC_CMD_DATA_BYTES + 3) > PAGE_SIZE);
+ BUILD_BUG_ON((OCC_RESP_DATA_BYTES + 7) > PAGE_SIZE);
+
+ return 0;
+}
+
+static ssize_t occ_read(struct file *file, char __user *buf, size_t len,
+ loff_t *offset)
+{
+ struct occ_client *client = file->private_data;
+ ssize_t rc = 0;
+
+ if (!client)
+ return -ENODEV;
+
+ if (len > OCC_SRAM_BYTES)
+ return -EINVAL;
+
+ mutex_lock(&client->lock);
+
+ /* This should not be possible ... */
+ if (WARN_ON_ONCE(client->read_offset > client->data_size)) {
+ rc = -EIO;
+ goto done;
+ }
+
+ /* Grab how much data we have to read */
+ rc = min(len, client->data_size - client->read_offset);
+ if (copy_to_user(buf, client->buffer + client->read_offset, rc))
+ rc = -EFAULT;
+ else
+ client->read_offset += rc;
+
+ done:
+ mutex_unlock(&client->lock);
+
+ return rc;
+}
+
+static ssize_t occ_write(struct file *file, const char __user *buf,
+ size_t len, loff_t *offset)
+{
+ struct occ_client *client = file->private_data;
+ size_t rlen, data_length;
+ u16 checksum = 0;
+ ssize_t rc, i;
+ u8 *cmd;
+
+ if (!client)
+ return -ENODEV;
+
+ if (len > (OCC_CMD_DATA_BYTES + 3) || len < 3)
+ return -EINVAL;
+
+ mutex_lock(&client->lock);
+
+ /* Construct the command */
+ cmd = client->buffer;
+
+ /* Sequence number (we could increment and compare with response) */
+ cmd[0] = 1;
+
+ /*
+ * Copy the user command (assume user data follows the occ command
+ * format)
+ * byte 0: command type
+ * bytes 1-2: data length (msb first)
+ * bytes 3-n: data
+ */
+ if (copy_from_user(&cmd[1], buf, len)) {
+ rc = -EFAULT;
+ goto done;
+ }
+
+ /* Extract data length */
+ data_length = (cmd[2] << 8) + cmd[3];
+ if (data_length > OCC_CMD_DATA_BYTES) {
+ rc = -EINVAL;
+ goto done;
+ }
+
+ /* Calculate checksum */
+ for (i = 0; i < data_length + 4; ++i)
+ checksum += cmd[i];
+
+ cmd[data_length + 4] = checksum >> 8;
+ cmd[data_length + 5] = checksum & 0xFF;
+
+ /* Submit command */
+ rlen = PAGE_SIZE;
+ rc = fsi_occ_submit(client->occ->dev, cmd, data_length + 6, cmd,
+ &rlen);
+ if (rc)
+ goto done;
+
+ /* Set read tracking data */
+ client->data_size = rlen;
+ client->read_offset = 0;
+
+ /* Done */
+ rc = len;
+
+ done:
+ mutex_unlock(&client->lock);
+
+ return rc;
+}
+
+static int occ_release(struct inode *inode, struct file *file)
+{
+ struct occ_client *client = file->private_data;
+
+ free_page((unsigned long)client->buffer);
+ kfree(client);
+
+ return 0;
+}
+
+static const struct file_operations occ_fops = {
+ .owner = THIS_MODULE,
+ .open = occ_open,
+ .read = occ_read,
+ .write = occ_write,
+ .release = occ_release,
+};
+
+static int occ_verify_checksum(struct occ_response *resp, u16 data_length)
+{
+ /* Fetch the two bytes after the data for the checksum. */
+ u16 checksum_resp = get_unaligned_be16(&resp->data[data_length]);
+ u16 checksum;
+ u16 i;
+
+ checksum = resp->seq_no;
+ checksum += resp->cmd_type;
+ checksum += resp->return_status;
+ checksum += (data_length >> 8) + (data_length & 0xFF);
+
+ for (i = 0; i < data_length; ++i)
+ checksum += resp->data[i];
+
+ if (checksum != checksum_resp)
+ return -EBADMSG;
+
+ return 0;
+}
+
+static int occ_getsram(struct occ *occ, u32 address, void *data, ssize_t len)
+{
+ u32 data_len = ((len + 7) / 8) * 8; /* must be multiples of 8 B */
+ size_t resp_len, resp_data_len;
+ __be32 *resp, cmd[5];
+ int rc;
+
+ /*
+ * Magic sequence to do SBE getsram command. SBE will fetch data from
+ * specified SRAM address.
+ */
+ cmd[0] = cpu_to_be32(0x5);
+ cmd[1] = cpu_to_be32(SBEFIFO_CMD_GET_OCC_SRAM);
+ cmd[2] = cpu_to_be32(1);
+ cmd[3] = cpu_to_be32(address);
+ cmd[4] = cpu_to_be32(data_len);
+
+ resp_len = (data_len >> 2) + OCC_SBE_STATUS_WORDS;
+ resp = kzalloc(resp_len << 2, GFP_KERNEL);
+ if (!resp)
+ return -ENOMEM;
+
+ rc = sbefifo_submit(occ->sbefifo, cmd, 5, resp, &resp_len);
+ if (rc)
+ goto free;
+
+ rc = sbefifo_parse_status(occ->sbefifo, SBEFIFO_CMD_GET_OCC_SRAM,
+ resp, resp_len, &resp_len);
+ if (rc)
+ goto free;
+
+ resp_data_len = be32_to_cpu(resp[resp_len - 1]);
+ if (resp_data_len != data_len) {
+ dev_err(occ->dev, "SRAM read expected %d bytes got %zd\n",
+ data_len, resp_data_len);
+ rc = -EBADMSG;
+ } else {
+ memcpy(data, resp, len);
+ }
+
+free:
+ /* Convert positive SBEI status */
+ if (rc > 0) {
+ dev_err(occ->dev, "SRAM read returned failure status: %08x\n",
+ rc);
+ rc = -EBADMSG;
+ }
+
+ kfree(resp);
+ return rc;
+}
+
+static int occ_putsram(struct occ *occ, u32 address, const void *data,
+ ssize_t len)
+{
+ size_t cmd_len, buf_len, resp_len, resp_data_len;
+ u32 data_len = ((len + 7) / 8) * 8; /* must be multiples of 8 B */
+ __be32 *buf;
+ int rc;
+
+ /*
+ * We use the same buffer for command and response, make
+ * sure it's big enough
+ */
+ resp_len = OCC_SBE_STATUS_WORDS;
+ cmd_len = (data_len >> 2) + 5;
+ buf_len = max(cmd_len, resp_len);
+ buf = kzalloc(buf_len << 2, GFP_KERNEL);
+ if (!buf)
+ return -ENOMEM;
+
+ /*
+ * Magic sequence to do SBE putsram command. SBE will transfer
+ * data to specified SRAM address.
+ */
+ buf[0] = cpu_to_be32(cmd_len);
+ buf[1] = cpu_to_be32(SBEFIFO_CMD_PUT_OCC_SRAM);
+ buf[2] = cpu_to_be32(1);
+ buf[3] = cpu_to_be32(address);
+ buf[4] = cpu_to_be32(data_len);
+
+ memcpy(&buf[5], data, len);
+
+ rc = sbefifo_submit(occ->sbefifo, buf, cmd_len, buf, &resp_len);
+ if (rc)
+ goto free;
+
+ rc = sbefifo_parse_status(occ->sbefifo, SBEFIFO_CMD_PUT_OCC_SRAM,
+ buf, resp_len, &resp_len);
+ if (rc)
+ goto free;
+
+ if (resp_len != 1) {
+ dev_err(occ->dev, "SRAM write response length invalid: %zd\n",
+ resp_len);
+ rc = -EBADMSG;
+ } else {
+ resp_data_len = be32_to_cpu(buf[0]);
+ if (resp_data_len != data_len) {
+ dev_err(occ->dev,
+ "SRAM write expected %d bytes got %zd\n",
+ data_len, resp_data_len);
+ rc = -EBADMSG;
+ }
+ }
+
+free:
+ /* Convert positive SBEI status */
+ if (rc > 0) {
+ dev_err(occ->dev, "SRAM write returned failure status: %08x\n",
+ rc);
+ rc = -EBADMSG;
+ }
+
+ kfree(buf);
+ return rc;
+}
+
+static int occ_trigger_attn(struct occ *occ)
+{
+ __be32 buf[OCC_SBE_STATUS_WORDS];
+ size_t resp_len, resp_data_len;
+ int rc;
+
+ BUILD_BUG_ON(OCC_SBE_STATUS_WORDS < 7);
+ resp_len = OCC_SBE_STATUS_WORDS;
+
+ buf[0] = cpu_to_be32(0x5 + 0x2); /* Chip-op length in words */
+ buf[1] = cpu_to_be32(SBEFIFO_CMD_PUT_OCC_SRAM);
+ buf[2] = cpu_to_be32(0x3); /* Mode: Circular */
+ buf[3] = cpu_to_be32(0x0); /* Address: ignore in mode 3 */
+ buf[4] = cpu_to_be32(0x8); /* Data length in bytes */
+ buf[5] = cpu_to_be32(0x20010000); /* Trigger OCC attention */
+ buf[6] = 0;
+
+ rc = sbefifo_submit(occ->sbefifo, buf, 7, buf, &resp_len);
+ if (rc)
+ goto error;
+
+ rc = sbefifo_parse_status(occ->sbefifo, SBEFIFO_CMD_PUT_OCC_SRAM,
+ buf, resp_len, &resp_len);
+ if (rc)
+ goto error;
+
+ if (resp_len != 1) {
+ dev_err(occ->dev, "SRAM attn response length invalid: %zd\n",
+ resp_len);
+ rc = -EBADMSG;
+ } else {
+ resp_data_len = be32_to_cpu(buf[0]);
+ if (resp_data_len != 8) {
+ dev_err(occ->dev,
+ "SRAM attn expected 8 bytes got %zd\n",
+ resp_data_len);
+ rc = -EBADMSG;
+ }
+ }
+
+ error:
+ /* Convert positive SBEI status */
+ if (rc > 0) {
+ dev_err(occ->dev, "SRAM attn returned failure status: %08x\n",
+ rc);
+ rc = -EBADMSG;
+ }
+
+ return rc;
+}
+
+int fsi_occ_submit(struct device *dev, const void *request, size_t req_len,
+ void *response, size_t *resp_len)
+{
+ const unsigned long timeout = msecs_to_jiffies(OCC_TIMEOUT_MS);
+ const unsigned long wait_time =
+ msecs_to_jiffies(OCC_CMD_IN_PRG_WAIT_MS);
+ struct occ *occ = dev_get_drvdata(dev);
+ struct occ_response *resp = response;
+ u16 resp_data_length;
+ unsigned long start;
+ int rc;
+
+ if (!occ)
+ return -ENODEV;
+
+ if (*resp_len < 7) {
+ dev_dbg(dev, "Bad resplen %zd\n", *resp_len);
+ return -EINVAL;
+ }
+
+ mutex_lock(&occ->occ_lock);
+
+ rc = occ_putsram(occ, OCC_SRAM_CMD_ADDR, request, req_len);
+ if (rc)
+ goto done;
+
+ rc = occ_trigger_attn(occ);
+ if (rc)
+ goto done;
+
+ /* Read occ response header */
+ start = jiffies;
+ do {
+ rc = occ_getsram(occ, OCC_SRAM_RSP_ADDR, resp, 8);
+ if (rc)
+ goto done;
+
+ if (resp->return_status == OCC_RESP_CMD_IN_PRG) {
+ rc = -ETIMEDOUT;
+
+ if (time_after(jiffies, start + timeout))
+ break;
+
+ set_current_state(TASK_UNINTERRUPTIBLE);
+ schedule_timeout(wait_time);
+ }
+ } while (rc);
+
+ /* Extract size of response data */
+ resp_data_length = get_unaligned_be16(&resp->data_length);
+
+ /* Message size is data length + 5 bytes header + 2 bytes checksum */
+ if ((resp_data_length + 7) > *resp_len) {
+ rc = -EMSGSIZE;
+ goto done;
+ }
+
+ dev_dbg(dev, "resp_status=%02x resp_data_len=%d\n",
+ resp->return_status, resp_data_length);
+
+ /* Grab the rest */
+ if (resp_data_length > 1) {
+ /* already got 3 bytes resp, also need 2 bytes checksum */
+ rc = occ_getsram(occ, OCC_SRAM_RSP_ADDR + 8,
+ &resp->data[3], resp_data_length - 1);
+ if (rc)
+ goto done;
+ }
+
+ *resp_len = resp_data_length + 7;
+ rc = occ_verify_checksum(resp, resp_data_length);
+
+ done:
+ mutex_unlock(&occ->occ_lock);
+
+ return rc;
+}
+EXPORT_SYMBOL_GPL(fsi_occ_submit);
+
+static int occ_unregister_child(struct device *dev, void *data)
+{
+ struct platform_device *hwmon_dev = to_platform_device(dev);
+
+ platform_device_unregister(hwmon_dev);
+
+ return 0;
+}
+
+static int occ_probe(struct platform_device *pdev)
+{
+ int rc;
+ u32 reg;
+ struct occ *occ;
+ struct platform_device *hwmon_dev;
+ struct device *dev = &pdev->dev;
+ struct platform_device_info hwmon_dev_info = {
+ .parent = dev,
+ .name = "occ-hwmon",
+ };
+
+ occ = devm_kzalloc(dev, sizeof(*occ), GFP_KERNEL);
+ if (!occ)
+ return -ENOMEM;
+
+ occ->dev = dev;
+ occ->sbefifo = dev->parent;
+ mutex_init(&occ->occ_lock);
+
+ if (dev->of_node) {
+ rc = of_property_read_u32(dev->of_node, "reg", ®);
+ if (!rc) {
+ /* make sure we don't have a duplicate from dts */
+ occ->idx = ida_simple_get(&occ_ida, reg, reg + 1,
+ GFP_KERNEL);
+ if (occ->idx < 0)
+ occ->idx = ida_simple_get(&occ_ida, 1, INT_MAX,
+ GFP_KERNEL);
+ } else {
+ occ->idx = ida_simple_get(&occ_ida, 1, INT_MAX,
+ GFP_KERNEL);
+ }
+ } else {
+ occ->idx = ida_simple_get(&occ_ida, 1, INT_MAX, GFP_KERNEL);
+ }
+
+ platform_set_drvdata(pdev, occ);
+
+ snprintf(occ->name, sizeof(occ->name), "occ%d", occ->idx);
+ occ->mdev.fops = &occ_fops;
+ occ->mdev.minor = MISC_DYNAMIC_MINOR;
+ occ->mdev.name = occ->name;
+ occ->mdev.parent = dev;
+
+ rc = misc_register(&occ->mdev);
+ if (rc) {
+ dev_err(dev, "failed to register miscdevice: %d\n", rc);
+ ida_simple_remove(&occ_ida, occ->idx);
+ return rc;
+ }
+
+ hwmon_dev_info.id = occ->idx;
+ hwmon_dev = platform_device_register_full(&hwmon_dev_info);
+ if (!hwmon_dev)
+ dev_warn(dev, "failed to create hwmon device\n");
+
+ return 0;
+}
+
+static int occ_remove(struct platform_device *pdev)
+{
+ struct occ *occ = platform_get_drvdata(pdev);
+
+ misc_deregister(&occ->mdev);
+
+ device_for_each_child(&pdev->dev, NULL, occ_unregister_child);
+
+ ida_simple_remove(&occ_ida, occ->idx);
+
+ return 0;
+}
+
+static const struct of_device_id occ_match[] = {
+ { .compatible = "ibm,p9-occ" },
+ { },
+};
+
+static struct platform_driver occ_driver = {
+ .driver = {
+ .name = "occ",
+ .of_match_table = occ_match,
+ },
+ .probe = occ_probe,
+ .remove = occ_remove,
+};
+
+static int occ_init(void)
+{
+ return platform_driver_register(&occ_driver);
+}
+
+static void occ_exit(void)
+{
+ platform_driver_unregister(&occ_driver);
+
+ ida_destroy(&occ_ida);
+}
+
+module_init(occ_init);
+module_exit(occ_exit);
+
+MODULE_AUTHOR("Eddie James <eajames@xxxxxxxxxxxxxxxxxx>");
+MODULE_DESCRIPTION("BMC P9 OCC driver");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/fsi-occ.h b/include/linux/fsi-occ.h
new file mode 100644
index 0000000..e28cf9a
--- /dev/null
+++ b/include/linux/fsi-occ.h
@@ -0,0 +1,34 @@
+/*
+ * On-Chip Controller Driver definitions and prototypes
+ *
+ * Copyright (C) IBM Corporation 2018
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef LINUX_FSI_OCC_H
+#define LINUX_FSI_OCC_H
+
+struct device;
+
+#define OCC_RESP_CMD_IN_PRG 0xFF
+#define OCC_RESP_SUCCESS 0
+#define OCC_RESP_CMD_INVAL 0x11
+#define OCC_RESP_CMD_LEN_INVAL 0x12
+#define OCC_RESP_DATA_INVAL 0x13
+#define OCC_RESP_CHKSUM_ERR 0x14
+#define OCC_RESP_INT_ERR 0x15
+#define OCC_RESP_BAD_STATE 0x16
+#define OCC_RESP_CRIT_EXCEPT 0xE0
+#define OCC_RESP_CRIT_INIT 0xE1
+#define OCC_RESP_CRIT_WATCHDOG 0xE2
+#define OCC_RESP_CRIT_OCB 0xE3
+#define OCC_RESP_CRIT_HW 0xE4
+
+int fsi_occ_submit(struct device *dev, const void *request, size_t req_len,
+ void *response, size_t *resp_len);
+
+#endif /* LINUX_FSI_OCC_H */
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
