[PATCH 6/8] ARM: dts: imx6qdl-apalis/-colibri: fix on-module regulators

[Stefan Agner <stefan@xxxxxxxx>]

Remove the 2.5V regulator, it does not exist. There is 3.3V and
3.3V_AUDIO provided to the module through the edge connector,
model those as fixed regulators like we use to do in other
Colibri device trees. The SGTL5000 uses 3.3V_AUDIO as VDDA. Note
that the driver derives the analog ground voltage (VAG) from this
supply. The new value should allow higher output swings before
clipping occurs. Refer to the SGTL5000 datasheet for details.

Signed-off-by: Stefan Agner <stefan@xxxxxxxx>
---
 arch/arm/boot/dts/imx6qdl-apalis.dtsi  | 22 +++++++++++-----------
 arch/arm/boot/dts/imx6qdl-colibri.dtsi | 20 ++++++++++----------
 2 files changed, 21 insertions(+), 21 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-apalis.dtsi b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
index 2f711fffa06e..6813f4326807 100644
--- a/arch/arm/boot/dts/imx6qdl-apalis.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
@@ -61,17 +61,17 @@
 		status = "disabled";
 	};
 
-	reg_2p5v: regulator-2p5v {
+	reg_module_3v3: regulator-module-3v3 {
 		compatible = "regulator-fixed";
-		regulator-name = "2P5V";
-		regulator-min-microvolt = <2500000>;
-		regulator-max-microvolt = <2500000>;
+		regulator-name = "+V3.3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
 		regulator-always-on;
 	};
 
-	reg_3p3v: regulator-3p3v {
+	reg_module_3v3_audio: regulator-module-3v3-audio {
 		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
+		regulator-name = "+V3.3_AUDIO";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		regulator-always-on;
@@ -314,8 +314,8 @@
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
-		VDDA-supply = <&reg_2p5v>;
-		VDDIO-supply = <&reg_3p3v>;
+		VDDA-supply = <&reg_module_3v3_audio>;
+		VDDIO-supply = <&reg_module_3v3>;
 	};
 
 	/* STMPE811 touch screen controller */
@@ -447,7 +447,7 @@
 &usdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_usdhc1_8bit>;
-	vqmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <8>;
 	disable-wp;
 	no-1-8-v;
@@ -458,7 +458,7 @@
 &usdhc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc2>;
-	vqmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <4>;
 	disable-wp;
 	no-1-8-v;
@@ -469,7 +469,7 @@
 &usdhc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
-	vqmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <8>;
 	no-1-8-v;
 	non-removable;
diff --git a/arch/arm/boot/dts/imx6qdl-colibri.dtsi b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
index 1a147cb0bed0..9a3bac5be5e2 100644
--- a/arch/arm/boot/dts/imx6qdl-colibri.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
@@ -56,17 +56,17 @@
 		status = "disabled";
 	};
 
-	reg_2p5v: regulator-2p5v {
+	reg_module_3v3: regulator-module-3v3 {
 		compatible = "regulator-fixed";
-		regulator-name = "2P5V";
-		regulator-min-microvolt = <2500000>;
-		regulator-max-microvolt = <2500000>;
+		regulator-name = "+V3.3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
 		regulator-always-on;
 	};
 
-	reg_3p3v: regulator-3p3v {
+	reg_module_3v3_audio: regulator-module-3v3-audio {
 		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
+		regulator-name = "+V3.3_AUDIO";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		regulator-always-on;
@@ -244,8 +244,8 @@
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
-		VDDA-supply = <&reg_2p5v>;
-		VDDIO-supply = <&reg_3p3v>;
+		VDDA-supply = <&reg_module_3v3_audio>;
+		VDDIO-supply = <&reg_module_3v3>;
 		lrclk-strength = <3>;
 	};
 
@@ -380,7 +380,7 @@
 	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_mmc_cd>;
 	cd-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; /* MMCD */
 	disable-wp;
-	vqmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <4>;
 	no-1-8-v;
 	status = "disabled";
@@ -390,7 +390,7 @@
 &usdhc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
-	vqmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <8>;
 	no-1-8-v;
 	non-removable;
-- 
2.18.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html