On Wed, Jul 04, 2018 at 06:44:08AM +0200, Daniel Mack wrote:
> This patch adds a generic w1 bindings document that merely describes how
> slave deviceses are grouped under master nodes. It also adds a specific
> binding for the ds2760 battery monitor.
>
> Signed-off-by: Daniel Mack <daniel@xxxxxxxxxx>
> ---
> .../bindings/power/supply/maxim,ds2760.txt | 29 +++++++++++++++++++
This has grown enough now, you should probably make it a separate
patch.
> .../devicetree/bindings/w1/w1-gpio.txt | 11 +++++--
> Documentation/devicetree/bindings/w1/w1.txt | 25 ++++++++++++++++
> 3 files changed, 62 insertions(+), 3 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt
> create mode 100644 Documentation/devicetree/bindings/w1/w1.txt
>
> diff --git a/Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt b/Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt
> new file mode 100644
> index 000000000000..a39d1ada48f2
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt
> @@ -0,0 +1,29 @@
> +Devicetree bindings for Maxim DS2760
> +====================================
> +
> +The ds2760 is a w1 slave device and must hence have its sub-node in DT
> +under a w1 bus master node.
> +
> +The device exposes a power supply, so the details described in
> +Documentation/devicetree/bindings/power/supply/power_supply.txt apply.
> +
> +Required properties:
> +- compatible: must be "maxim,ds2760"
> +
> +Optional properties:
> +- power-supplies: Refers to one or more power supplies connected to
> + this battery.
> +- maxim,pmod-enabled: This boolean property enables the DS2760 to enter
> + sleep mode when the DQ line goes low for greater
> + than 2 seconds and leave sleep Mode when the DQ
> + line goes high.
> +- maxim,cache-time: Time im milliseconds to cache the data for. When
Add unit suffix as defined in property-units.txt.
> + this time expires, the values are read again from
> + the hardware. Defaults to 1000.
> +- maxim,rated-capacity: The rated capacity of the battery, in mAh.
Seems like this should be common.
> + If not specified, the value stored in the
> + non-volatile chip memory is used.
> +- maxim,current-accumulator:
> + The current accumulator value in mAh.
> + If not specified, the value stored in the
> + non-volatile chip memory is used.
This would be updated periodically while running and then restored after
a power cycle or reboot to maintain the battery level across power
cycle? I don't think that belongs in DT as we don't really define
whether a DT can be updated persistently.
> diff --git a/Documentation/devicetree/bindings/w1/w1-gpio.txt b/Documentation/devicetree/bindings/w1/w1-gpio.txt
> index 6e09c35d9f1a..3d6554eac240 100644
> --- a/Documentation/devicetree/bindings/w1/w1-gpio.txt
> +++ b/Documentation/devicetree/bindings/w1/w1-gpio.txt
> @@ -13,10 +13,15 @@ Optional properties:
> - linux,open-drain: if specified, the data pin is considered in
> open-drain mode.
>
> +Also refer to the generic w1.txt document.
> +
> Examples:
>
> - onewire@0 {
> + onewire {
> compatible = "w1-gpio";
> - gpios = <&gpio 126 0>, <&gpio 105 0>;
> - };
> + gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
>
> + battery {
> + // ...
> + };
> + };
> diff --git a/Documentation/devicetree/bindings/w1/w1.txt b/Documentation/devicetree/bindings/w1/w1.txt
> new file mode 100644
> index 000000000000..bee18f7070ec
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/w1/w1.txt
> @@ -0,0 +1,25 @@
> +Generic devicetree bindings for onewire (w1) busses
> +===================================================
> +
> +Onewire busses are described through nodes of their master bus controller.
> +Slave devices are listed as sub-nodes of such master devices. For now, only
> +one slave is allowed per bus master.
> +
> +
> +Example:
> +
> + charger: charger {
> + compatible = "gpio-charger";
> + charger-type = "mains";
> + gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
> + };
> +
> + onewire@0 {
Drop the unit-address.
> + compatible = "w1-gpio";
> + gpios = <&gpio 100 0>, <&gpio 101 0>;
> +
> + battery {
> + compatible = "maxim,ds2760";
> + power-supplies = <&charger>;
> + };
> + };
> --
> 2.17.1
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
