Hi Paul,
On 3 July 2018 at 18:02, Paul Cercueil <paul@xxxxxxxxxxxxxxx> wrote:
> The only information we use in the 8-word version of the hardware DMA
> descriptor that is not present in the 4-word version is the transfer
> type, aka. the ID of the source or recipient device.
>
> Since the transfer type will never change for a DMA channel in use,
> we can just set it once for all in the corresponding DMA register
> before starting any transfer.
>
> This has several benefits:
>
> * the driver will handle twice as many hardware DMA descriptors;
>
> * the driver is closer to support the JZ4740, which only supports 4-word
> hardware DMA descriptors;
>
> * the JZ4770 SoC needs the transfer type to be set in the corresponding
> DMA register anyway, even if 8-word descriptors are in use.
>
> Signed-off-by: Paul Cercueil <paul@xxxxxxxxxxxxxxx>
> ---
> drivers/dma/dma-jz4780.c | 21 +++++++++------------
> 1 file changed, 9 insertions(+), 12 deletions(-)
>
> diff --git a/drivers/dma/dma-jz4780.c b/drivers/dma/dma-jz4780.c
> index 4d234caf5d62..cd2cd70fd843 100644
> --- a/drivers/dma/dma-jz4780.c
> +++ b/drivers/dma/dma-jz4780.c
> @@ -93,17 +93,12 @@
> * @dtc: transfer count (number of blocks of the transfer size specified in DCM
> * to transfer) in the low 24 bits, offset of the next descriptor from the
> * descriptor base address in the upper 8 bits.
> - * @sd: target/source stride difference (in stride transfer mode).
> - * @drt: request type
> */
> struct jz4780_dma_hwdesc {
> uint32_t dcm;
> uint32_t dsa;
> uint32_t dta;
> uint32_t dtc;
> - uint32_t sd;
> - uint32_t drt;
> - uint32_t reserved[2];
> };
>
> /* Size of allocations for hardware descriptor blocks. */
> @@ -280,7 +275,6 @@ static int jz4780_dma_setup_hwdesc(struct jz4780_dma_chan *jzchan,
> desc->dcm = JZ_DMA_DCM_SAI;
> desc->dsa = addr;
> desc->dta = config->dst_addr;
> - desc->drt = jzchan->transfer_type;
>
> width = config->dst_addr_width;
> maxburst = config->dst_maxburst;
> @@ -288,7 +282,6 @@ static int jz4780_dma_setup_hwdesc(struct jz4780_dma_chan *jzchan,
> desc->dcm = JZ_DMA_DCM_DAI;
> desc->dsa = config->src_addr;
> desc->dta = addr;
> - desc->drt = jzchan->transfer_type;
>
> width = config->src_addr_width;
> maxburst = config->src_maxburst;
> @@ -433,9 +426,10 @@ static struct dma_async_tx_descriptor *jz4780_dma_prep_dma_memcpy(
> tsz = jz4780_dma_transfer_size(dest | src | len,
> &jzchan->transfer_shift);
>
> + jzchan->transfer_type = JZ_DMA_DRT_AUTO;
> +
> desc->desc[0].dsa = src;
> desc->desc[0].dta = dest;
> - desc->desc[0].drt = JZ_DMA_DRT_AUTO;
> desc->desc[0].dcm = JZ_DMA_DCM_TIE | JZ_DMA_DCM_SAI | JZ_DMA_DCM_DAI |
> tsz << JZ_DMA_DCM_TSZ_SHIFT |
> JZ_DMA_WIDTH_32_BIT << JZ_DMA_DCM_SP_SHIFT |
> @@ -490,9 +484,12 @@ static void jz4780_dma_begin(struct jz4780_dma_chan *jzchan)
> (jzchan->curr_hwdesc + 1) % jzchan->desc->count;
> }
>
> - /* Use 8-word descriptors. */
> - jz4780_dma_chn_writel(jzdma, jzchan->id,
> - JZ_DMA_REG_DCS, JZ_DMA_DCS_DES8);
> + /* Use 4-word descriptors. */
> + jz4780_dma_chn_writel(jzdma, jzchan->id, JZ_DMA_REG_DCS, 0);
> +
> + /* Set transfer type. */
> + jz4780_dma_chn_writel(jzdma, jzchan->id, JZ_DMA_REG_DRT,
> + jzchan->transfer_type);
>
> /* Write descriptor address and initiate descriptor fetch. */
> desc_phys = jzchan->desc->desc_phys +
> @@ -502,7 +499,7 @@ static void jz4780_dma_begin(struct jz4780_dma_chan *jzchan)
>
> /* Enable the channel. */
> jz4780_dma_chn_writel(jzdma, jzchan->id, JZ_DMA_REG_DCS,
> - JZ_DMA_DCS_DES8 | JZ_DMA_DCS_CTE);
> + JZ_DMA_DCS_CTE);
> }
>
> static void jz4780_dma_issue_pending(struct dma_chan *chan)
> --
> 2.18.0
>
>
Patch looks good to me.
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@xxxxxxxxx>
Regards,
PrasannaKumar
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
