On Thu, Jun 28, 2018 at 06:20:52PM +0200, Marco Felsch wrote:
> The TVP5150/1 decoders support different video input sources to their
> AIP1A/B pins.
>
> Possible configurations are as follows:
> - Analog Composite signal connected to AIP1A.
> - Analog Composite signal connected to AIP1B.
> - Analog S-Video Y (luminance) and C (chrominance)
> signals connected to AIP1A and AIP1B respectively.
>
> This patch extends the device tree bindings documentation to describe
> how the input connectors for these devices should be defined in a DT.
>
> Signed-off-by: Marco Felsch <m.felsch@xxxxxxxxxxxxxx>
> ---
> .../devicetree/bindings/media/i2c/tvp5150.txt | 118 +++++++++++++++++-
> 1 file changed, 113 insertions(+), 5 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
> index 8c0fc1a26bf0..feed8c911c5e 100644
> --- a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
> +++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
> @@ -12,11 +12,23 @@ Optional Properties:
> - pdn-gpios: phandle for the GPIO connected to the PDN pin, if any.
> - reset-gpios: phandle for the GPIO connected to the RESETB pin, if any.
>
> -The device node must contain one 'port' child node for its digital output
> -video port, in accordance with the video interface bindings defined in
> -Documentation/devicetree/bindings/media/video-interfaces.txt.
> +The device node must contain one 'port' child node per device input and output
> +port, in accordance with the video interface bindings defined in
> +Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
> +are numbered as follows
>
> -Required Endpoint Properties for parallel synchronization:
> + Name Type Port
> + --------------------------------------
> + AIP1A sink 0
> + AIP1B sink 1
> + S-VIDEO sink 2
> + Y-OUT src 3
> +
> +The device node must contain at least the Y-OUT port. Each input port must be
> +linked to an endpoint defined in
> +Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt.
> +
> +Required Endpoint Properties for parallel synchronization on output port:
>
> - hsync-active: active state of the HSYNC signal. Must be <1> (HIGH).
> - vsync-active: active state of the VSYNC signal. Must be <1> (HIGH).
> @@ -26,7 +38,9 @@ Required Endpoint Properties for parallel synchronization:
> If none of hsync-active, vsync-active and field-even-active is specified,
> the endpoint is assumed to use embedded BT.656 synchronization.
>
> -Example:
> +Examples:
> +
> +Only Output:
>
> &i2c2 {
> ...
> @@ -37,6 +51,100 @@ Example:
> reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
>
> port {
> + reg = <3>;
> + tvp5150_1: endpoint {
> + remote-endpoint = <&ccdc_ep>;
> + };
> + };
> + };
> +};
> +
> +One Input:
> +
> +connector@0 {
Drop the unit-address as there is no reg property.
> + compatible = "composite-video-connector";
> + label = "Composite0";
> +
> + port {
> + comp0_out: endpoint {
> + remote-endpoint = <&tvp5150_comp0_in>;
> + };
> + };
> +};
> +
> +&i2c2 {
> + ...
> + tvp5150@5c {
> + compatible = "ti,tvp5150";
> + reg = <0x5c>;
> + pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>;
> + reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
> +
> + port@0 {
> + reg = <0>;
> + tvp5150_comp0_in: endpoint {
> + remote-endpoint = <&comp0_out>;
> + };
> + };
> +
> + port@3 {
> + reg = <3>;
> + tvp5150_1: endpoint {
> + remote-endpoint = <&ccdc_ep>;
> + };
> + };
> + };
> +};
> +
> +
> +Two Inputs, different connector 12 on input AIP1A:
> +
> +connector@1 {
ditto
> + compatible = "svideo-connector";
> + label = "S-Video";
> +
> + port {
> + svideo_out: endpoint {
> + remote-endpoint = <&tvp5150_svideo_in>;
> + };
> + };
> +};
> +
> +connector@12 {
ditto
> + compatible = "composite-video-connector";
> + label = "Composite12";
> +
> + port {
> + comp12_out: endpoint {
> + remote-endpoint = <&tvp5150_comp12_in>;
> + };
> + };
> +};
> +
> +&i2c2 {
> + ...
> + tvp5150@5c {
> + compatible = "ti,tvp5150";
> + reg = <0x5c>;
> + pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>;
> + reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
> +
> + port@0 {
> + reg = <0>;
> + tvp5150_comp12_in: endpoint {
> + remote-endpoint = <&comp12_out>;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> + tvp5150_svideo_in: endpoint {
> + remote-endpoint = <&svideo_out>;
> + };
> + };
> +
> + port@3 {
> + reg = <3>;
> tvp5150_1: endpoint {
> remote-endpoint = <&ccdc_ep>;
> };
> --
> 2.17.1
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
