On Thu, Jun 21, 2018 at 12:39:47PM -0700, Jae Hyun Yoo wrote:
> This commit adds a document of generic PECI bus, adapter and client
> driver.
>
> Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@xxxxxxxxxxxxxxx>
> Reviewed-by: Haiyue Wang <haiyue.wang@xxxxxxxxxxxxxxx>
> Reviewed-by: James Feist <james.feist@xxxxxxxxxxxxxxx>
> Reviewed-by: Vernon Mauery <vernon.mauery@xxxxxxxxxxxxxxx>
> Cc: Andrew Jeffery <andrew@xxxxxxxx>
> Cc: Joel Stanley <joel@xxxxxxxxx>
> ---
> .../devicetree/bindings/peci/peci.txt | 60 +++++++++++++++++++
> 1 file changed, 60 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/peci/peci.txt
>
> diff --git a/Documentation/devicetree/bindings/peci/peci.txt b/Documentation/devicetree/bindings/peci/peci.txt
> new file mode 100644
> index 000000000000..5583aa80b78a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/peci/peci.txt
> @@ -0,0 +1,60 @@
> +Generic device tree configuration for PECI buses
> +================================================
> +
> +Required properties:
> +- compatible : Should be "simple-bus".
> +- #address-cells : Should be present if the device has sub-nodes.
> +- #size-cells : Should be present if the device has sub-nodes.
> +- ranges : Should contain PECI controller registers ranges.
> +
> +Example:
> + peci: peci@10000000 {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0x0 0x10000000 0x1000>;
> + };
I don't think you need this section. It's just the parent of the
controller, right?
> +
> +Generic device tree configuration for PECI adapters
> +===================================================
> +
> +Required properties:
> +- #address-cells : Should be <1>. Read more about client addresses below.
> +- #size-cells : Should be <0>. Read more about client addresses below.
> +
> +The cells properties above define that an address of CPU clients of a PECI bus
> +are described by a single value.
> +
> +Example:
> + peci0: peci-bus@0 {
> + compatible = "vendor,soc-peci";
> + reg = <0x0 0x1000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> +Generic device tree configuration for PECI clients
> +==================================================
> +
> +Required properties:
> +- compatible : Should contain name of PECI client.
> +- reg : Should contain address of a client CPU. Address range of CPU
> + clients starts from 0x30 based on PECI specification.
> +
> +Example:
> + peci-bus@0 {
> + compatible = "vendor,soc-peci";
> + reg = <0x0 0x1000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + peci-client@30 {
> + compatible = "vendor,peci-client";
> + reg = <0x30>;
> + };
> +
> + peci-client@31 {
> + compatible = "vendor,peci-client";
> + reg = <0x31>;
> + };
> + };
> --
> 2.17.1
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
