Hi Matthias,
On 2018-06-26 05:35, Matthias Kaehlcke wrote:
On Mon, Jun 25, 2018 at 04:43:54PM -0700, Matthias Kaehlcke wrote:
This is a nice improvement, a few remaining questions inline.
On Mon, Jun 25, 2018 at 07:10:10PM +0530, Balakrishna Godavarthi
wrote:
> In function qca_setup, we set initial and operating speeds for Qualcomm
> Bluetooth SoC's. This block of code is common across different
> Qualcomm Bluetooth SoC's. Instead of duplicating the code, created
> a wrapper function to set the speeds. So that future coming SoC's
> can use these wrapper functions to set speeds.
>
> Signed-off-by: Balakrishna Godavarthi <bgodavar@xxxxxxxxxxxxxx>
> ---
> Changes in v8:
> * common function to set INIT and operating speeds.
> * moved hardware flow control to qca_set_speed().
>
> Changes in v7:
> * initial patch
> * created wrapper functions for init and operating speeds.
> ---
> drivers/bluetooth/hci_qca.c | 89 +++++++++++++++++++++++++++----------
> 1 file changed, 65 insertions(+), 24 deletions(-)
>
> diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
> index fe62420ef838..38b7dbe6c897 100644
> --- a/drivers/bluetooth/hci_qca.c
> +++ b/drivers/bluetooth/hci_qca.c
> @@ -119,6 +119,11 @@ struct qca_data {
> u64 votes_off;
> };
>
> +enum qca_speed_type {
> + QCA_INIT_SPEED = 1,
> + QCA_OPER_SPEED
> +};
> +
> struct qca_serdev {
> struct hci_uart serdev_hu;
> struct gpio_desc *bt_en;
> @@ -923,6 +928,60 @@ static inline void host_set_baudrate(struct hci_uart *hu, unsigned int speed)
> hci_uart_set_baudrate(hu, speed);
> }
>
> +static unsigned int qca_get_speed(struct hci_uart *hu,
> + enum qca_speed_type speed_type)
> +{
> + unsigned int speed = 0;
> +
> + if (speed_type == QCA_INIT_SPEED) {
> + if (hu->init_speed)
> + speed = hu->init_speed;
> + else if (hu->proto->init_speed)
> + speed = hu->proto->init_speed;
> + } else {
> + if (hu->oper_speed)
> + speed = hu->oper_speed;
> + else if (hu->proto->oper_speed)
> + speed = hu->proto->oper_speed;
> + }
> +
> + return speed;
> +}
> +
> +static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
> +{
> + unsigned int speed, qca_baudrate;
> + int ret;
> +
> + if (speed_type == QCA_INIT_SPEED) {
> + speed = qca_get_speed(hu, QCA_INIT_SPEED);
> + if (speed)
> + host_set_baudrate(hu, speed);
> + else
> + bt_dev_err(hu->hdev, "Init speed should be non zero");
The check for 'speed == 0' is done in multiple places. From this
code I deduce that it is expected that both INIT and OPER speed are
set to non-zero values. What happens if either of them is zero? Is the
driver still operational?
> + return 0;
> + }
> +
> + speed = qca_get_speed(hu, QCA_OPER_SPEED);
> + if (!speed) {
> + bt_dev_err(hu->hdev, "operating speed should be non zero");
> + return 0;
> + }
> +
> + qca_baudrate = qca_get_baudrate_value(speed);
> + bt_dev_info(hu->hdev, "Set UART speed to %d", speed);
> + ret = qca_set_baudrate(hu->hdev, qca_baudrate);
> + if (ret) {
> + bt_dev_err(hu->hdev, "Failed to change the baudrate (%d)", ret);
> + return ret;
> + }
> +
> + host_set_baudrate(hu, speed);
> +
> + return ret;
> +}
In the discussion on "[v7,8/8] Bluetooth: hci_qca: Add support for
Qualcomm Bluetooth chip wcn3990" you mentioned the possbility to move
the hci_uart_set_flow_control() calls into _set_speed(). This seemed
interesting but finally it isn't done in this series. Did you
encounter that it is not feasible/desirable for some reason?
I got that half wrong. "[v8,7/7] Bluetooth: hci_qca: Add support for
Qualcomm Bluetooth chip wcn3990" adds the flow control calls to
_set_speed() however there are still_set_flow_control() calls in
qca_setup(), which confused/s me.
Could you provide a brief summary on the situations (relevant for this
driver) in which flow controls needs to be enabled/disabled?
you will not find enable or disable of hardware flow control in this
patch.
there is no hardware flow control in ROME chip.
you will find hardware flow control in wcn3990 i.e. patch [v8 7/7]
in wcn3990. we disable hardware flow control, when we sent mandatory
commands to BT chip.
i.e while sending power on pulse i.e 0xFC byte for wcn3990 to boot up
completely and sending change baudrate request to BT chip.
before sending these commands, we disable the chip flow control and
enable flow control once we sent these commands.
so in our current code after integrating wcn3990, we disable flow
control two times.
1. Before sending power on pulse i.e. qca_send_vendor_cmd(hdev,
QCA_WCN3990_POWERON_PULSE); in qca_setup.
so we find disable or enable hardware flow control in qca_setup()
2. Before sending change BT CHIP baudrate request i.e.
qca_set_baudrate(hu->hdev, qca_baudrate); in qca_set_speed().
--
Regards
Balakrishna.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
