On 21 June 2018 at 21:09, Paweł Chmiel <pawel.mikolaj.chmiel@xxxxxxxxx> wrote:
> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@xxxxxxxxx>
Please add commit message. This can be something as simple as "Add
Samsung Galaxy S DTS which is a commercial phone based on Aries
family." or something more (e.g. describe what is working).
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/s5pv210-galaxys.dts | 72 +++++++++++++++++++++++++++++++++++
> 2 files changed, 73 insertions(+)
> create mode 100644 arch/arm/boot/dts/s5pv210-galaxys.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 7e2424957809..522ebdca1d3d 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -846,6 +846,7 @@ dtb-$(CONFIG_ARCH_S3C64XX) += \
> s3c6410-smdk6410.dtb
> dtb-$(CONFIG_ARCH_S5PV210) += \
> s5pv210-aquila.dtb \
> + s5pv210-galaxys.dtb \
> s5pv210-goni.dtb \
> s5pv210-smdkc110.dtb \
> s5pv210-smdkv210.dtb \
> diff --git a/arch/arm/boot/dts/s5pv210-galaxys.dts b/arch/arm/boot/dts/s5pv210-galaxys.dts
> new file mode 100644
> index 000000000000..d435032541a9
> --- /dev/null
> +++ b/arch/arm/boot/dts/s5pv210-galaxys.dts
> @@ -0,0 +1,72 @@
> +// SPDX-License-Identifier: GPL-2.0
> +
> +/dts-v1/;
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
Duplicated inclusion.
> +#include "s5pv210-aries.dtsi"
> +
> +/ {
> + model = "Samsung Galaxy S1 (GT-I9000) based on S5PV210";
> + compatible = "samsung,galaxys", "samsung,aries", "samsung,s5pv210";
> +
> + chosen {
> + bootargs = "console=ttySAC2,115200n8 root=/dev/mmcblk2p1 rw rootwait ignore_loglevel earlyprintk";
stdout-path = "serial2:115200n8";
Rest of bootargs should not be here (they are not HW dependent) unless
you cannot configure them through bootloader?
> + };
> +
> + nand_pwrseq: nand-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&gpj2 7 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&massmemory_en>;
massmemory_en is used only here, so please move it from aries.dtsi.
The same applies to all other possible properties if they are not used
in other DTSes including aries.
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> +
> + power {
> + label = "power";
> + gpios = <&gph2 6 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_POWER>;
> + wakeup-source;
> + };
> +
> + vol-down {
> + label = "volume_down";
> + gpios = <&gph3 1 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_VOLUMEDOWN>;
> + };
> +
> + vol-up {
> + label = "volume_up";
> + gpios = <&gph3 2 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_VOLUMEUP>;
> + };
> +
> + home {
> + label = "home";
> + gpios = <&gph3 5 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_HOME>;
> + wakeup-source;
> + };
> + };
> +};
> +
> +&pinctrl0 {
> + massmemory_en: massmemory-en {
Oh wait, I see massmemory_en here... so there is no need of such in aries.dtsi.
Best regards,
Krzysztof
> + samsung,pins = "gpj2-7";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> + samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
> + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
> + };
> +};
> +
> +&sdhci0 {
> + bus-width = <4>;
> + non-removable;
> + mmc-pwrseq = <&nand_pwrseq>;
> + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>;
> + pinctrl-names = "default";
> + status = "okay";
> +};
> --
> 2.7.4
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
